Husqvarna PT26 D manual Electrical system

Page 68

Electrical system

Chapter 10: Electrical system

1. Headlight

2. Indicator panel

3. Control panel

4. Circuit board

5. Circuit fuses

6. Starter

7. Generator

8. Sensor engine temperature (2)

9. Oil pressure sensor (concealed)

10. Fuses and main relay

11. Main fuse

12. Battery

13. Magnetic coupling for power take-off

Electrical system, component locations

67

Image 68

Contents PT26 D Contents Page Introduction CongratulationsDriving and Transport on Public Roads TowingProper Service Serial NumberSymbols and Decals Important Information Safety Instructions General UseWhen driving Driving on slopes Do as followsMaintenance ChildrenAvoid sparking and its consequences by Other protective devices are not ﬁtted or are defective Transport Environment protectionUser responsibility Presentation Placement of controls Speed control Parking brakeControl panel SeatAdjusting the cutting height Steering wheel and steering wheel consoleDifferential Lock FuellingControls on the control panel Control lever hydraulicsWinter fuel and parafﬁn precipitation Lifting the cutting unit transport positionSwitch for operation of cutting unit Switch for extra hydraulic function hydraulic kit optionIndicators trafﬁc kit option Push button for horn trafﬁc kit optionStarter switch HeadlightThrottle control High speedWeight transfer Spare Power outletRotating warning light trafﬁc kit option Parking lights trafﬁc kit optionLever for steering wheel console angle Adjusting the steering wheel settingChronometer Rops Cooling system Cutting unit AntifreezeAccessories Driving Mowing TipsBefore Starting Start gas or ether must not be used for this engineStarting the engine Starting with a weak battery Starting in cold conditionsDriving the machine Braking Cutting the engineBleeding in the event of fuel stoppage Engine stop250 500 1000 2000 MaintenanceMaintenance Schedule 250 500 1000 2000 Cleaning Cleaning the radiators heat exchanger Adjusting the pump and generator drive beltsRemoving the machine’s covers Checking radiatorgrillesChecking and adjusting the throttle control Adjusting the parking brakeReplacing the pump and generator drive belts Checking the exhaust systemCleaning the cyclone ﬁlter Servicing the air ﬁlterReplacing the air ﬁlter Emptying the particle trapChecking the Tyre Pressures Bleeding the fuel systemServicing the fuel ﬁlter Servicing the battery FusesChecking the Safety System FU2 FU9Replacing the bulb in the headlight Light setting Cutting Unit ComponentsAttaching and removing the cutting unit Side shifting the cutting unitImportant Information Setting the cutting height and tilt angle Cutting heightCutting Unit’s Service Position Placing in the Service PositionTilt angle Ground pressureReleasing the Service Position Cutting Unit ModelAlways replace the belts in pairs Replacing the power take-off beltsChecking the Blades Replacing the belt on the Combi unit Adjusting the power take-off beltsReplacing the cutting unit belt Removal of BioClip Plug Lubrication Lubrication ScheduleGeneral Lubricating the cablesHandle for cutting height setting Lubricating in Accordance with Lubrication SchedulePivot wheel bearings Cutting unit’s bevel gearPower take-off shaft’s front support bearing Lift cylinderEngine Oil Viscosity and qualityFilling engine oil Changing the Engine OilReplacing the engine’s oil ﬁlter Hydraulic oilInspection off the oil level Filling hydraulic oilHydraulic oil ﬁlter, change Cutting unit mountingLifting arm’s rear bearings Driver’s SeatParking brake cables Control cylinderLubrication Trouble Shooting Guide Problem CauseProblem Cause Problem Cause Trouble Shooting Guide Storage Winter StorageService Electrical system Hydraulic System Hydraulic System Fuel system Technical Data Data PT 26DTransmission Vibration levels4 Technical Data Diverse design standards Design standardsEU Declaration of Conformity only applies to Europe Design standards Page Page 1153893-26 ´z+Uy@¶6u¨ ´z+Uy@¶6u¨ Original instructions