Husqvarna ProFlex 21 manual Transport

Page 14

SAFETY INSTRUCTIONS

Never use the machine indoors or in spaces lacking proper ventilation. Exhaust fumes contain carbon monoxide, an odourless, poisonous and highly dangerous gas.

Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting.

Never make adjustments with the engine running.

The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer.

The blades are sharp and can cause cuts and gashes. Wrap the blades or wear protective gloves when handling them.

Check the parking brake’s functionality regularly. Adjust and maintain as required.

The mulching unit should only be used where better quality mowing is required and in known areas.

Reduce the risk of fire by removing grass, leaves and other debris that may have fastened in the machine. Allow the machine to cool before putting it in storage.

Transport

IMPORTANT INFORMATION

The parking brake is not sufficient to lock the machine during transport. Ensure you secure the machine firmly to the transporting vehicle.

The machine is heavy and can cause serious crush injuries. Be especially careful when it is loaded in or out of a car or on and off of a trailer.

Use an approved trailer to transport the machine. Activate the parking brake and secure the machine using approved fasteners, such as straps, chains or ropes when transporting.

Check and abide by local traffic regulations before transporting or driving the machine on any road.

English-12

8009-467

Never drive the machine in an enclosed space

8010-061

Regularly clean grass, leaves and other debris from the machine

Image 14
Contents Rider ProFlex 18 Rider ProFlex Svenska Contents Operator’s Manual for Rider ProFlex 18 and ProFlexImportant Information Introduction IntroductionProper Service Serial NumberExplanation of Symbols Symbols and decalsXxxxxxx xxxx xxxxxxxx xxx xxx xxxx xxxxxx General use Safety InstructionsSafety instructions Keep children away from the work area Driving on slopes Do not drive down slopes with the unit raised Do as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationPlacement of Controls Accelerator Throttle ControlChoke Lever Cutting unit AccessoriesLights and power outlet Lifting the cutting unit transport position Cutting height adjustment leverLever for hydraulic lift of attachments, PF Lowering the unit mowing positionMowing position Mechanical lifting lever for cutting unitTransport position Fuelling Parking brakeSeat Chronometer Differential lock, PFClutch control Driving Mowing tipsStarting the engine DrivingBefore Starting Impaired cooling of the engine. Risk of major engine damageDo not run the starter motor for more than Driving the Rider, PF Stopping the engine, PF English-26 English-27 English-28 Maintenance schedule MaintenanceMaintenance = Described in this manual = Not described in this manual English-31 Front cover Removing the Rider’s coversEngine cover Right-hand wing coverTransmission cover Left-hand wing coverChecking the engine’s cooling air intake Cleaning the engine and muffler Checking the transmission air intakeChecking and adjusting the steering cables Adjusting the differential lock, PF Checking and adjusting the throttle cableChecking and adjusting the choke cable Adjusting the hydrostatic transmission cable Cable holderAdjusting the parking brake Poorly adjusted brake can result in reduced braking abilityReplacing the air filter Replacing the air filter, PFEnglish-40 English-41 Checking the fuel pump’s air filter Cleaning the pulse air filterReplacing the fuel filter Ignition system Checking the battery acid levelChecking the tyre pressures Wrong spark plug type can damage the engineFuses Replacing the spark plugChecking the safety system Replacing the light bulbs Exercise caution Risk of crush injuries Cutting unit componentsAttaching the cutting unit Watch your fingers. Do not turn the blades or the belt Check that the belt is around the idler Belt Sketch Cutting height ParallelismReleasing the service position Cutting unit’s service positionPlacing in the service position Ground pressureCutting unit model Checking the bladesRemoving the cutting unit Exercise caution. Risk of crush injuriesPull out the unit so that it catches on the outer hooks Removing the unit frame Removing the beltAttaching the belt Hook the spring to the blade brakeChanging the cutting unit’s belt Removal of BioClip Plug Lubrication schedule, PF LubricationLubrication English-60 General Lubricating the cablesLubricating in accordance with the lubrication schedule Pedal mechanism in frame tunnelChains in the frame tunnel Differential lock cable, PFEngine oil Oil is topped up through the hole the dipstick sitsReplacing the engine oil Driver’s seat Gear leverTransmission Throttle and choke cables, lever bearings Hydraulic oil filter, change, PF Oil filter, changeParking Brake Cable Transmission oil levelEnglish-70 Problem Cause Trouble ShootingTrouble Shooting Guide English-72 Winter Storage StorageStorage Service Electrical and Hydraulic Systems Electrical systemEnglish-76 Hydraulic system, PF English-78 Technical Data Technical dataCutting unit Combi Data Rider ProFlex Hydraulic SystemTransmission EU Declaration of Conformity only applies to Europe EU Declaration of ConformityEU Declaration of Conformity ProFlex 18 01/901/009 ProFlex 21 01/901/010English-82 Action Service JournalService journal After the First 8 HoursAction Date, mileage reading, stamp Signature Hour Service English-85 English-86 English-87 English-88 Action Date, mileage reading, stamp, signature English-90 Svenska ´z+H6T¶68¨ Svenska 114 02