Husqvarna ProFlex 21 manual Adjusting the hydrostatic transmission cable, Cable holder

Page 39

MAINTENANCE

Adjusting the hydrostatic transmission cable

The hydrostatic transmission cable (on the left side) is adjusted in the following manner:

1.Remove the transmission cover. Loosen both screws (one on each side) and lift off the transmission cover.

2.Take apart the lower ball joint, which is locked with a locking spring.

3.Ensure that the forward drive pedal is pressed down completely.

4.Switch the vertical arm to the maximum position and check that the ball and socket in the lower ball joint are aligned.

5.Adjust the socket on the cable if needed.

6.Assemble the lower ball joint.

7.Put the ball joint’s locking spring in place.

6008-209

6020-002

Cable holder

The cable seat in the middle protects the cables and the hydraulic tubes so that they do not get pinched during turns. It is situated close to the ground and can be damaged by objects or careless driving, especially when reversing.

Check to ensure that it is undamaged and that the belt guide is properly centred on the rear side of the pulley.

8009-364

English-37

Image 39

Contents Rider ProFlex 18 Rider ProFlex Svenska Operator’s Manual for Rider ProFlex 18 and ProFlex ContentsImportant Information Introduction IntroductionSerial Number Proper ServiceSymbols and decals Explanation of SymbolsXxxxxxx xxxx xxxxxxxx xxx xxx xxxx xxxxxx Safety Instructions Safety instructionsGeneral use Keep children away from the work area Do not drive down slopes with the unit raised Do as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Presentation PresentationPlacement of Controls Throttle Control Choke LeverAccelerator Accessories Lights and power outletCutting unit Lowering the unit mowing position Cutting height adjustment leverLever for hydraulic lift of attachments, PF Lifting the cutting unit transport positionMechanical lifting lever for cutting unit Transport positionMowing position Parking brake SeatFuelling Differential lock, PF Clutch controlChronometer Mowing tips DrivingImpaired cooling of the engine. Risk of major engine damage DrivingBefore Starting Starting the engineDo not run the starter motor for more than Driving the Rider, PF Stopping the engine, PF English-26 English-27 English-28 Maintenance MaintenanceMaintenance schedule = Described in this manual = Not described in this manual English-31 Right-hand wing cover Removing the Rider’s coversEngine cover Front coverLeft-hand wing cover Checking the engine’s cooling air intakeTransmission cover Checking the transmission air intake Cleaning the engine and mufﬂerChecking and adjusting the steering cables Checking and adjusting the throttle cable Checking and adjusting the choke cableAdjusting the differential lock, PF Cable holder Adjusting the hydrostatic transmission cablePoorly adjusted brake can result in reduced braking ability Adjusting the parking brakeReplacing the air ﬁlter, PF Replacing the air ﬁlterEnglish-40 English-41 Cleaning the pulse air ﬁlter Replacing the fuel ﬁlterChecking the fuel pump’s air ﬁlter Wrong spark plug type can damage the engine Checking the battery acid levelChecking the tyre pressures Ignition systemReplacing the spark plug FusesChecking the safety system Replacing the light bulbs Cutting unit components Attaching the cutting unitExercise caution Risk of crush injuries Watch your ﬁngers. Do not turn the blades or the belt Check that the belt is around the idler Belt Sketch Parallelism Cutting heightGround pressure Cutting unit’s service positionPlacing in the service position Releasing the service positionChecking the blades Cutting unit modelExercise caution. Risk of crush injuries Removing the cutting unitPull out the unit so that it catches on the outer hooks Removing the belt Removing the unit frameHook the spring to the blade brake Attaching the beltChanging the cutting unit’s belt Removal of BioClip Plug Lubrication LubricationLubrication schedule, PF English-60 Lubricating the cables GeneralPedal mechanism in frame tunnel Lubricating in accordance with the lubrication scheduleDifferential lock cable, PF Chains in the frame tunnelOil is topped up through the hole the dipstick sits Engine oilReplacing the engine oil Gear lever TransmissionDriver’s seat Throttle and choke cables, lever bearings Oil ﬁlter, change Hydraulic oil ﬁlter, change, PFTransmission oil level Parking Brake CableEnglish-70 Trouble Shooting Trouble Shooting GuideProblem Cause English-72 Storage StorageWinter Storage Service Electrical system Electrical and Hydraulic SystemsEnglish-76 Hydraulic system, PF English-78 Technical data Technical DataData Rider ProFlex Hydraulic System TransmissionCutting unit Combi ProFlex 18 01/901/009 ProFlex 21 01/901/010 EU Declaration of ConformityEU Declaration of Conformity EU Declaration of Conformity only applies to EuropeEnglish-82 After the First 8 Hours Service JournalService journal ActionAction Date, mileage reading, stamp Signature Hour Service English-85 English-86 English-87 English-88 Action Date, mileage reading, stamp, signature English-90 Svenska ´z+H6T¶68¨ Svenska 114 02