Husqvarna ProFlex 21 manual Removal of BioClip Plug

Page 60

MAINTENANCE

Removal of BioClip Plug

To change a Combi unit from the BioClip function to a cutting unit with rear ejection, remove the BioClip plug, which is located under the unit, attached with three screws.

1.Put the unit in service position, see “The cutting unit’s service position” on page 51.

2.Remove the three screws holding the BioClip plug, and remove the plug.

Tip: Fit three full-thread screws M8x15 mm in the screw holes to protect the threads.

3.Return the unit to the normal position.

Fit the BioClip plug in the reverse order.

8009-289

Removal of BioClip Plug

English-58

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Rider ProFlex 18 Rider ProFlex Svenska Contents Operator’s Manual for Rider ProFlex 18 and ProFlexImportant Information Introduction IntroductionProper Service Serial NumberExplanation of Symbols Symbols and decalsXxxxxxx xxxx xxxxxxxx xxx xxx xxxx xxxxxx Safety Instructions Safety instructionsGeneral use Keep children away from the work area Driving on slopes Do not drive down slopes with the unit raised Do as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationPlacement of Controls Throttle Control Choke LeverAccelerator Accessories Lights and power outletCutting unit Cutting height adjustment lever Lever for hydraulic lift of attachments, PFLifting the cutting unit transport position Lowering the unit mowing positionMechanical lifting lever for cutting unit Transport positionMowing position Parking brake SeatFuelling Differential lock, PF Clutch controlChronometer Driving Mowing tipsDriving Before StartingStarting the engine Impaired cooling of the engine. Risk of major engine damageDo not run the starter motor for more than Driving the Rider, PF Stopping the engine, PF English-26 English-27 English-28 Maintenance MaintenanceMaintenance schedule = Described in this manual = Not described in this manual English-31 Removing the Rider’s covers Engine coverFront cover Right-hand wing coverLeft-hand wing cover Checking the engine’s cooling air intakeTransmission cover Cleaning the engine and muffler Checking the transmission air intakeChecking and adjusting the steering cables Checking and adjusting the throttle cable Checking and adjusting the choke cableAdjusting the differential lock, PF Adjusting the hydrostatic transmission cable Cable holderAdjusting the parking brake Poorly adjusted brake can result in reduced braking abilityReplacing the air filter Replacing the air filter, PFEnglish-40 English-41 Cleaning the pulse air filter Replacing the fuel filterChecking the fuel pump’s air filter Checking the battery acid level Checking the tyre pressuresIgnition system Wrong spark plug type can damage the engineFuses Replacing the spark plugChecking the safety system Replacing the light bulbs Cutting unit components Attaching the cutting unitExercise caution Risk of crush injuries Watch your fingers. Do not turn the blades or the belt Check that the belt is around the idler Belt Sketch Cutting height ParallelismCutting unit’s service position Placing in the service positionReleasing the service position Ground pressureCutting unit model Checking the bladesRemoving the cutting unit Exercise caution. Risk of crush injuriesPull out the unit so that it catches on the outer hooks Removing the unit frame Removing the beltAttaching the belt Hook the spring to the blade brakeChanging the cutting unit’s belt Removal of BioClip Plug Lubrication LubricationLubrication schedule, PF English-60 General Lubricating the cablesLubricating in accordance with the lubrication schedule Pedal mechanism in frame tunnelChains in the frame tunnel Differential lock cable, PFEngine oil Oil is topped up through the hole the dipstick sitsReplacing the engine oil Gear lever TransmissionDriver’s seat Throttle and choke cables, lever bearings Hydraulic oil filter, change, PF Oil filter, changeParking Brake Cable Transmission oil levelEnglish-70 Trouble Shooting Trouble Shooting GuideProblem Cause English-72 Storage StorageWinter Storage Service Electrical and Hydraulic Systems Electrical systemEnglish-76 Hydraulic system, PF English-78 Technical Data Technical dataData Rider ProFlex Hydraulic System TransmissionCutting unit Combi EU Declaration of Conformity EU Declaration of ConformityEU Declaration of Conformity only applies to Europe ProFlex 18 01/901/009 ProFlex 21 01/901/010English-82 Service Journal Service journalAction After the First 8 HoursAction Date, mileage reading, stamp Signature Hour Service English-85 English-86 English-87 English-88 Action Date, mileage reading, stamp, signature English-90 Svenska ´z+H6T¶68¨ Svenska 114 02
Top Page Image Contents