Web Interface | 3Com iCV-01a, iCV-08, iCV-03a specification

Chapter 3: Web Interface

To change Video Codec, click Click Save to confirm changes.

Note: The availability of Codec depends on weather the individual user has it installed on the PC or not. Download and install Windows Media Player 10 to enable MPEG4 codec.

Digital Zoom In, Digital Zoom Out

Rotate Left, Rotate Right

Flip the image vertically.

HotSpot icon. Each item corresponds to HotSpot location set in Basic Setting Patrol Settings Hotspot Setting. Click to jump to the pre-set location.

Click S to recalibrate and center the camera.

Note:

These icons will not show if you do not have either, (1) a CM03a Pan Tilt camera, (2) administrator permission or (3) operator permission.

Directional Tool. Click to move the camera 1 degree in the direction of the arrow.

Directional Tool. Click to move the camera 5 degrees in the direction of the arrow.

Auto Patrol icon. Click to enable auto patrolling.

Note:

If the account permission is Viewer, then the HotSpot icon, Directional Tool and Auto Patrol icon will not be available.

WebCAM - user manual

-9-

Image 12

3Com iCV-01a, iCV-08, iCV-03a user manual Web Interface

Contents

WebCAM ICV-01a / iCV-03a / iCV-08 Contents Page Features Introduction Package Contents WebCAM Front and Back view Hardware Installation Step Web Interface Introduction Using the Web Interface View Video Information Basic Settings Advanced Settings Using ActiveX Controls To View Video Web Interface Web Interface Using Sun Java Controls Web Interface Information System StatusSystem Information Ii. Network Status Current Connections Event Log WebCAM Event Log Operator privilege Basic Settings Camera Settings Patrol Settings HotSpot Settings BoundaryAuto Patrolling Format Network Primary DNS Server IP Secondary DNS Server IPIv. Port Number Http Port Number Use Default Domain Name WebCAM Default Dynamic DNS Registration complete. Account details shown as follows Service Provider Login NameLogin Password Ii. Other Dynamic DNS Account Settings When Connection should be madeUse Public IP to register Iii. PPPoE Password User NamePermission IP Filter Ii. Block IP address Blocked IP List Advanced Settings Event Notification Recipients Events Web Interface Event Notification Camera a Motion Detected Enable Motion DetectionCamera a or Camera B Always On or Detection Sensitivity Send image every … secondsStop sending after … emails or image idle for … seconds Schedule Loop from … to … Digits …Email Server … Recipient Image Recording Begin End hhmmSend image every … minutes Send to FTP Server & Send Email Mail / FTP Email of Image Recorded FTP Settings Ii. Email SettingsEmail Server Requires Authentication FTP Server Iii. Sending Test Mail Sending a test mail System Settings Iv. Email Address Book System Time Updates System TimeTime Server Iii. LED Settings Iv. Snmp SettingsTime Zone Relative to GMT System Time yyyy/mm/dd hhmmss Image Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Language Interface LanguageIi. Email Preference Ii. Save / Restore Settings Save Current ConfigurationRestore Previous Configuration Reset to factory default View Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Using the Utility Installation Setup Wizard Click on Setup WizardBasic Settings Account Settings Obtain an IP address by Dhcp Use the following IP Address Obtain an IP address by Bootp Select Enable PPPoE connection Using the Utility Program Launch WebCAM Using the Utility Program IP Configuration IP Address Advanced for password and Http configuration Device Password when accessing from Utility Click IP Configuration Ii. Management Protocol Upgrade Firmware Refresh User can do a manual search by clicking the Refresh Installing MultiMonitor MultiMonitor MultiMonitor MultiMonitor Device Access by WebCAM Address Host Address Remote Port Access by Image Server Image Server AddressUser Password Image Server Port MultiMonitor Display the current Camera settings Camera Select AccountImage Zoom Camera Rotation Display the Motion Detection Settings Enable Motion When MotionDetect Sensitivity Compression Path Configure Settings for Email Notification Snmp Settings Using Snmp to update network portsProtocol MultiMonitor MultiMonitor MultiMonitor View System Change Password … UserAccount Management… Help Add User…Permission Choose Manager or User Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Appendix a Router Configuration Port Forwarding for WebCAM SMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B Methods to Update WebCAM Firmware Method 2 Using the Utility softwareMethod 1 Through WebCAM Web Appendix C IP Address, Subnet and Gateway Subnetting and Subnet Masks Subnet Mask Routing and Filtering Appendix D Glossary Term Definition