Network | 3Com iCV-01a, iCV-08, iCV-03a instruction

Chapter 3: Web Interface

b.Square – The camera will patrol along the user defined boundary in a clock wise manner.

c.Pan only – The camera will perform Pan function only.

d.Tilt only – The camera will perform tilt function only.

e.In sequence (1-5) – The camera will jump to each Hotspot location in sequence and wait for 10 seconds in each spot.

Pan speed / Tilt Speed

Use this to define the Pan and Tilt speed. By default this is set to 10, the fastest setting. The administrator can further customize by choosing different Pan / Tilt speed.

2.3.3 Network

This option determines WebCAM Network settings.

ii.IP Address

By default, the IP address acquisition is set to using DHCP.

Fig.16 WebCAM IP Address Settings

IP Address

This determines WebCAM LAN IP address.

Subnet Mask

Enter WebCAM Subnet Mask. The value is normally 255.255.255.0

Gateway

This item is to set WebCAM Gateway.

To learn more about the above, see Appendix C: IP address, Subnet and

Gateway

Obtain an IP address

This allows the user to choose either to set WebCAM LAN IP address; manually, using DHCP (default) or using Bootp protocol.

Note:

Click Apply to confirm. WebCAM will reboot. You MUST manually enter the NEW IP address in your Browser in order to open the Web Interface.

iii.DNS Server IP

WebCAM - user manual

-18-

Image 21

3Com iCV-01a, iCV-08, iCV-03a user manual Network

Contents

ICV-01a / iCV-03a / iCV-08 WebCAM Contents Page Introduction Features Package Contents WebCAM Front and Back view Step Hardware Installation Introduction Web Interface View Video Information Basic Settings Advanced Settings Using the Web Interface To View Video Using ActiveX Controls Web Interface Web Interface Using Sun Java Controls Web Interface System Status InformationSystem Information Ii. Network Status Event Log Current Connections WebCAM Event Log Operator privilege Camera Settings Basic Settings Patrol Settings Boundary HotSpot SettingsAuto Patrolling Format Network Secondary DNS Server IP Primary DNS Server IPIv. Port Number Http Port Number WebCAM Default Dynamic DNS Use Default Domain Name Registration complete. Account details shown as follows Login Name Service ProviderLogin Password Ii. Other Dynamic DNS When Connection should be made Account SettingsUse Public IP to register Iii. PPPoE User Name PasswordPermission IP Filter Blocked IP List Ii. Block IP address Event Notification Advanced Settings Events Recipients Web Interface Event Notification Camera a Motion Detected Motion Detection EnableCamera a or Camera B Always On or Send image every … seconds Detection SensitivityStop sending after … emails or image idle for … seconds Schedule Digits … Loop from … to …Email Server … Recipient Begin End hhmm Image RecordingSend image every … minutes Send to FTP Server & Send Email Email of Image Recorded Mail / FTP Ii. Email Settings FTP SettingsEmail Server Requires Authentication FTP Server Sending a test mail Iii. Sending Test Mail Iv. Email Address Book System Settings System Time Updates System TimeTime Server Iv. Snmp Settings Iii. LED SettingsTime Zone Relative to GMT System Time yyyy/mm/dd hhmmss Image Server Choose Yes to enable this feature or No to disable Community. Click Add to add WebCAM to My List Unit added to My List Language Interface LanguageIi. Email Preference Save Current Configuration Ii. Save / Restore SettingsRestore Previous Configuration Reset to factory default View Images Using PDA / PPC / mobile View Images Using PDA / PPC / mobile Installation Using the Utility Setup Wizard Click on Setup WizardBasic Settings Account Settings Use the following IP Address Obtain an IP address by Dhcp Select Enable PPPoE connection Obtain an IP address by Bootp Using the Utility Program Launch WebCAM Using the Utility Program IP Address IP Configuration Device Password when accessing from Utility Advanced for password and Http configuration Ii. Management Protocol Click IP Configuration Refresh Upgrade Firmware User can do a manual search by clicking the Refresh MultiMonitor Installing MultiMonitor MultiMonitor MultiMonitor Device Access by Image Server Image Server Address Access by WebCAM Address Host Address Remote PortUser Password Image Server Port MultiMonitor Account Display the current Camera settings Camera SelectImage Zoom Camera Rotation When Motion Display the Motion Detection Settings Enable MotionDetect Sensitivity Path Compression Configure Settings for Email Notification Snmp Settings Using Snmp to update network portsProtocol MultiMonitor MultiMonitor MultiMonitor System View Change Password … UserAccount Management… Help Add User…Permission Choose Manager or User Drag-and-Drop Feature Double click on the icon on the desktop, to view the images Port Forwarding for WebCAM Appendix a Router Configuration SMC SMC2404WBR Appendix a Router Configuration TCP UDP TCP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP TCP Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B Methods to Update WebCAM Firmware Method 2 Using the Utility softwareMethod 1 Through WebCAM Web Appendix C IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet Masks Term Definition Appendix D Glossary