Status Messages, Network Interface NI | ADTRAN ESU 120e guide

A ppendix C. System Messages

Status Messages

Network Interface (NI)

Payload On	Payload loopback activated

Line On	Loopback off

Loopback Off	All loopbacks deactivated

Factory Restore	Factory setting restored

Power On	Unit powered on

Self-Test	Internal self-test performed

Nx56/ 64 Interface

The following messages indicate the status of the Nx56/64 card:

Loop Up	Data is looped at both the network interface
	and DTE interface of the card

Remote Loop Up	Sending V.54 pattern in an attempt to loop up a
	remote device

511 Pattern On	Sending 511 pattern towards the network
	interface

Loop Down	Data is no longer looped back at the network
	interface or DTE interface

511 Pattern Off	No longer sending 511 pattern towards the
	network interface

D rop (PBX) Interface

The following messages indicate the status of the Drop interface:

Frame Slip	Indicates a Frame Slip has occurred on the Drop
	interface; this is present in Alarm History only

Line Loop Up	Line loopback activated

Port Loop Up	Port loopback activated

Loopdown	Loopback has been deactivated

C-4

ESU 120e User Manual

1200420L1-1

Image 114

ADTRAN ESU 120e user manual Status Messages, Network Interface NI, Nx56/ 64 Interface

Contents

ESU 120e Part Number 1200420L1-1 Trademarks Adtran Web Site Product Matrix Faxback Document Line Y2K Project LineMail Page Canadian Emissions Requirements Canadian Equipment Limitations Vii Important Safety Instructions Warranty and Customer Service Page Table of Contents Chapter Operation SnmpChapter Status Menu Chapter Test Menu Chapter Configuration MenuChapter Utility Menu Local Loopbck Remote Loopbck Test Pattern DIS 511 Reslt Pattern ResultLoopbk Telnet/Terminal Menus Appendix A. Understanding Snmp Index-1 Xvi 61200420L1-1 List of Figures List of Figures List of Tables List of Tables Introduction ESU 120E Overview ESU 120e Features ESU Option Modules ESU 120E Configuration Applications Option Module ArchitectureRouter, PBX Application Introduction AD Tran Shipments Include UNPACK, INSPECT, Power UPReceipt Inspection Customer Provides Power Connection Ground ING Instructions Installation ID Entification of Rear Panel Layout ESU 120e Rear Panel Network Test Interface ESU120E InterfacesNetwork Interfaces Nx56/ 64 Serial Interface POWER-UP Testing Self-Test Unit-level tests InitializationBoard-level tests Set User Passcode Set Control Port Chain In PCChain In/ Chain Out Normal POWER-UP Proced URE Installation Peration Front Panel 11 12 16 17 ESU 120e Front Panel Layout LED D escriptions CSU StatusSU/ D rop Status Operation keys Module Status General Menu Operation Select and Activate a Menu Item NI Perf Rpts NI Errors 4VIEW History END of ListPort Status Remote Port Clear Port ALM Enet Status Ata Port Identification Front Panel Menu StructureExit Any Menu Field Operation Or D isplay Alternate Methods of Control Watch PRO AD Tran PC Program Step Action Terminal Mode Telnet Status Menu Network Interface Performance Reports NI Perf Rpts Network Interface Performance Report Network Interface Errors NI Errors Active Alarms D isplay of Alarm Messages View History TE Status Port StatusNx56/ 64 Menu Items D TE D ata/ CK Port Rate Remote Port Clear Port AlarmRop Menu Items D SX Errors Enet Status Configuration Menu Configuration Menu Tree Menu Item Description Network NINetwork NI Menu Items Intface From the NI. See ESU 120 Clock Sources on page 5-5 for more ESU 120e Clock Sources Network Timed Network Timed Clock Source Base D rop Timed D rop Timed Clock Source Base D TE Timed Internal Timing Internal Clock Source Normal CSU Timing Normal CSU Unit Menu May not be used as a terminal interface Slip Map Exchange Map Xchng Map In Use ABOFF TS0 Map a and TS0 Map B D S0 Map D esignations Copy a Temp Create TempIdle Edit Temp Review MAPReview Temp Apply Temp a Port Configuration Port Config Nx56/ 64 Port Configuration Port Config Menu Items DCD DataCTS DSR Normal Mode of Operation Rop Port Configuration Port Config Menu Items Configuration Menu Utility Menu Set Passcode Factory RestoreTime/ D ate Enter Passcode from Other Menus Special Feature Change/ Set a PasscodeNo Passcode D esired To Set the Unit Identification Unit IDSoftware Revision Software Rev No Unit ID D esired CMD Mode Port UtilityEnet Address Utility Menu Test Menu Network Tests Loopback TestsNetwork Interface Loopbacks All Ones Line On Activates the line loopbackBCK All Zeros Qrss Pattern Qrss always runs at 64K/TS0 BES SESSync Run Self-Test Port Tests Test Name What it does Remote Port Test Menu Items for 0.1 Nx56PRT/LCL Patt Cancel Tests Port Test Menu Items for 0.2 D rop Loopback Test Menu Main Menu Telnet/ Terminal Main Menu Status, Config, Util, and Test Menu Options TS0 Maps Configuration Menu Applying the Temp Map Initializing the Temp MapEditing the Temp Map Reviewing Temp Maps Snmp Read Community Remote Menu AccessManagement Configuration Snmp Read/ Write Community Snmp Trap Community Auth. Fail Traps Sent Telnet/ Terminal TimeoutTelnet/ Terminal Password Poll Link Status Traps Sent Flash D ownload Quit Session Telnet/Terminal Menus Snmp Basic Components Network ManagerAgent GetRequest Command SMIB GetNextRequest GetResponse ESU 120E Snmp AccessMessages Trap Snmp Trap Configuration Snmp MIB Browser Configuration Snmp MIB Files Ppendix a . Understanding Snmp Connector type 15-pin female D connector WiringNetwork interface Connector Table B-1. Network Pinouts Table B-2. Control In/ Chain-in Pinout Connector type RJ-48 Part Number AMP#Control In/ Chain Pin Name Description Table B-3. Chain-Out Connector Pinout Chain OutConnections Table B-4. Nx56/ 64 Pin Assignments for EIA-530 Connector type Pin female D connectorAta Port Interface Pin Table B-5. Nx56/ 64 Pin Assignments for V.35 Mode Ccitt Table B-6. Adapter Cable, D B 25 to V.35, 34-Pin Winchester 1200285L1 DB25P Pin 34 Pin Name Table B-7. Nx56/ 64 Pin Assignments for V.11/ x.21 Mode Pin Name Description Source Base D rop PBX Table B-8. Adapter Cable D B25 to X.21, D B15 ConnectorTable B-9. Pinout Connectors for Terminal Interface Name DB25Pin DA15S Pin Table B-10 BaseT Pinout Connector type Shielded RJ48 USOCPart Number AMP #10BaseT Pin Name To Nic Ppendix B. Connector Pinouts Alarm Messages Network Interface NI Nx56/ 64 Interface Rop Port Interface Status Messages Network Interface NINx56/ 64 Interface CRC-4, FAS,CAS Electrical SpecificationsNetwork Interface HDB3 CTS, DCD, DSR Nx56/ 64 D rop Port InterfaceNx56/ 64 V.35 Interface Rop Port Interface Watch Management InterfacesChain In/ Out Ports Option Slot Interface Chassis Specifications Environmental Specifications Index NI Errors Snmptrap Configuration A-4 Index-4 Presales Inquiries and Applications Support Post-Sale SupportRepair and Return