Auth. Fail Traps Sent, Ping IP Host, Exit | ADTRAN ESU 120e specification

Chapter 8. Telnet/Terminal Menus

Auth. Fail Traps Sent

(DISABLED, ENABLED: defaults to DISABLED)

When enabled, the ESU 120e issues an SNMP trap when any SNMP request is received with an invalid community name. Can be used for security purposes.

Poll Link Status Traps Sent

(DISABLED, ENABLED, defaults to DISABLED)

When enabled, the ESU 120e sends an SNMP trap whenever a device configured to be polled fails to respond. When the device begins responding to polls, a poll link-up trap is sent. The format of the traps are defined in the agent MIB.

Ping IP Host

Allows the user to Ping a specific IP address.

Telnet/ Terminal Timeout

The ESU 120e terminates a telnet or terminal session if no activity is detected for this length of time. Only one telnet or terminal session may be active at one time. This timeout prevents an unattended session from blocking interactive access to the agent. The default value is five minutes.

Telnet/ Terminal Password

This option allows modification of the password required for entry into a telnet or terminal session. The default value is ADTRAN.

Exit

Returns to the ESU 120e Main menu.

8-6

ESU 120e User Manual

61200420L1-1

Image 92

ADTRAN ESU 120e Auth. Fail Traps Sent, Poll Link Status Traps Sent, Ping IP Host, Telnet/ Terminal Timeout, Exit

Contents

ESU 120e Part Number 1200420L1-1 Trademarks Mail Adtran Web Site Product Matrix Faxback Document LineY2K Project Line Page Canadian Emissions Requirements Canadian Equipment Limitations Vii Important Safety Instructions Warranty and Customer Service Page Table of Contents Chapter Status Menu Chapter OperationSnmp Chapter Configuration Menu Chapter Utility MenuChapter Test Menu Local Loopbck Remote Loopbck Test Pattern Pattern Result LoopbkDIS 511 Reslt Telnet/Terminal Menus Appendix A. Understanding Snmp Index-1 Xvi 61200420L1-1 List of Figures List of Figures List of Tables List of Tables Introduction ESU 120E Overview ESU 120e Features ESU Option Modules Router, PBX Application ESU 120E Configuration ApplicationsOption Module Architecture Introduction UNPACK, INSPECT, Power UP Receipt InspectionAD Tran Shipments Include Customer Provides Power Connection Ground ING Instructions Installation ID Entification of Rear Panel Layout ESU 120e Rear Panel ESU120E Interfaces Network InterfacesNetwork Test Interface Nx56/ 64 Serial Interface POWER-UP Testing Self-Test Initialization Board-level testsUnit-level tests Set User Passcode Chain In/ Chain Out Set Control PortChain In PC Normal POWER-UP Proced URE Installation Peration Front Panel 11 12 16 17 ESU 120e Front Panel Layout SU/ D rop Status LED D escriptionsCSU Status Operation keys Module Status General Menu Operation Select and Activate a Menu Item Port Status Remote Port Clear Port ALM Enet Status NI Perf Rpts NI Errors4VIEW History END of List Exit Any Menu Field Operation Or D isplay Ata Port IdentificationFront Panel Menu Structure Alternate Methods of Control Watch PRO AD Tran PC Program Step Action Terminal Mode Telnet Status Menu Network Interface Performance Reports NI Perf Rpts Network Interface Performance Report Network Interface Errors NI Errors Active Alarms D isplay of Alarm Messages View History Port Status Nx56/ 64 Menu Items D TE D ata/ CKTE Status Port Rate Clear Port Alarm Rop Menu Items D SX ErrorsRemote Port Enet Status Configuration Menu Configuration Menu Tree Network NI Network NI Menu ItemsMenu Item Description Intface From the NI. See ESU 120 Clock Sources on page 5-5 for more ESU 120e Clock Sources Network Timed Network Timed Clock Source Base D rop Timed D rop Timed Clock Source Base D TE Timed Internal Timing Internal Clock Source Normal CSU Timing Normal CSU Unit Menu May not be used as a terminal interface Slip OFF Map Exchange Map XchngMap In Use AB TS0 Map a and TS0 Map B D S0 Map D esignations Idle Copy a TempCreate Temp Review MAP Review TempEdit Temp Apply Temp a Port Configuration Port Config Nx56/ 64 Port Configuration Port Config Menu Items Data CTSDCD DSR Normal Mode of Operation Rop Port Configuration Port Config Menu Items Configuration Menu Utility Menu Factory Restore Time/ D ateSet Passcode Enter Passcode from Other Menus No Passcode D esired Special FeatureChange/ Set a Passcode Unit ID Software Revision Software RevTo Set the Unit Identification No Unit ID D esired Enet Address CMD ModePort Utility Utility Menu Test Menu Network Interface Loopbacks Network TestsLoopback Tests Line On Activates the line loopback BCKAll Ones All Zeros Qrss Pattern Qrss always runs at 64K/TS0 Sync BESSES Run Self-Test Port Tests Test Name What it does Port Test Menu Items for 0.1 Nx56 PRT/LCLRemote Patt Cancel Tests Port Test Menu Items for 0.2 D rop Loopback Test Menu Main Menu Telnet/ Terminal Main Menu Status, Config, Util, and Test Menu Options TS0 Maps Configuration Menu Initializing the Temp Map Editing the Temp MapApplying the Temp Map Reviewing Temp Maps Remote Menu Access Management ConfigurationSnmp Read Community Snmp Read/ Write Community Snmp Trap Community Telnet/ Terminal Timeout Telnet/ Terminal PasswordAuth. Fail Traps Sent Poll Link Status Traps Sent Flash D ownload Quit Session Telnet/Terminal Menus Agent Snmp Basic ComponentsNetwork Manager Command S MIBGetRequest GetNextRequest ESU 120E Snmp Access MessagesGetResponse Trap Snmp Trap Configuration Snmp MIB Browser Configuration Snmp MIB Files Ppendix a . Understanding Snmp Wiring Network interface ConnectorConnector type 15-pin female D connector Table B-1. Network Pinouts Connector type RJ-48 Part Number AMP# Control In/ ChainTable B-2. Control In/ Chain-in Pinout Pin Name Description Connections Table B-3. Chain-Out Connector PinoutChain Out Connector type Pin female D connector Ata Port InterfaceTable B-4. Nx56/ 64 Pin Assignments for EIA-530 Pin Table B-5. Nx56/ 64 Pin Assignments for V.35 Mode Ccitt Table B-6. Adapter Cable, D B 25 to V.35, 34-Pin Winchester 1200285L1 DB25P Pin 34 Pin Name Table B-7. Nx56/ 64 Pin Assignments for V.11/ x.21 Mode Pin Name Description Source Table B-8. Adapter Cable D B25 to X.21, D B15 Connector Table B-9. Pinout Connectors for Terminal InterfaceBase D rop PBX Name DB25Pin DA15S Pin Connector type Shielded RJ48 USOCPart Number AMP # 10BaseTTable B-10 BaseT Pinout Pin Name To Nic Ppendix B. Connector Pinouts Alarm Messages Network Interface NI Nx56/ 64 Interface Rop Port Interface Nx56/ 64 Interface Status MessagesNetwork Interface NI Electrical Specifications Network InterfaceCRC-4, FAS,CAS HDB3 Nx56/ 64 D rop Port Interface Nx56/ 64 V.35 InterfaceCTS, DCD, DSR Rop Port Interface Management Interfaces Chain In/ Out PortsWatch Option Slot Interface Chassis Specifications Environmental Specifications Index NI Errors Snmptrap Configuration A-4 Index-4 Repair and Return Presales Inquiries and Applications SupportPost-Sale Support