Alarm Messages, Network Interface NI | ADTRAN ESU 120e instruction

A ppendix C

System Messages

ALARM MESSAGES

This appendix lists and defines the alarm and status messages that appear on the ESU 120e screen.

Network Interface (NI)

Loss of Frame	NI unable to frame align with incoming FAS /NFAS framing
	pattern. Remote Alarm (Bit 3 of NFAS word) is transmitted out
	the network interface. AIS (unframed ones) is transmitted out
	the drop port.

Loss of TS16MF	NI unable to sync on TS16 multiframe signal. Valid only when
	CAS/TS16 framing enabled. Remote multiframe Alarm is
	transmitted out the network interface. ASI is transmitted out
	the drop port in TS16 only.

Remote Alarm	Remote alarm signal (Bit 3 of NFAS word) being received at
	network interface.

Remote MF	Remote multiframe alarm signal (Bit 6 of TS16 for three
Alarm	consecutive multiframes) being received at network interface.

AIS Received	Unframed ones being received at network interface. AIS
	transmitted out drop port interface.

TS16 AIS RCVD	Unframed ones being received in TS16 on network interface.
	Remote multiframe alarm transmitted out network interface.
	AIS in TS16 is transmitted out drop port.

Loss of CRC-4	NI unable to sync on CRC-4 multiframe signal. Valid only
	when CRC-4 framing is enabled. Remote Alarm is transmitted
	out the network interface. AIS is transmitted out the drop port.

Loss of Signal	No signal detected at NI

1200420L1-1

ESU 120e User Manual

C-1

Image 111

ADTRAN ESU 120e user manual Alarm Messages, Network Interface NI

Contents

Part Number 1200420L1-1 ESU 120e Trademarks Adtran Web Site Product Matrix Faxback Document Line Y2K Project LineMail Page Canadian Emissions Requirements Canadian Equipment Limitations Vii Important Safety Instructions Warranty and Customer Service Page Table of Contents Chapter Operation SnmpChapter Status Menu Local Loopbck Remote Loopbck Test Pattern Chapter Configuration MenuChapter Utility Menu Chapter Test Menu Telnet/Terminal Menus Pattern ResultLoopbk DIS 511 Reslt Index-1 Appendix A. Understanding Snmp Xvi 61200420L1-1 List of Figures List of Figures List of Tables List of Tables ESU 120E Overview Introduction ESU Option Modules ESU 120e Features ESU 120E Configuration Applications Option Module ArchitectureRouter, PBX Application Introduction Customer Provides UNPACK, INSPECT, Power UPReceipt Inspection AD Tran Shipments Include Ground ING Instructions Power Connection Installation ESU 120e Rear Panel ID Entification of Rear Panel Layout Nx56/ 64 Serial Interface ESU120E InterfacesNetwork Interfaces Network Test Interface Self-Test POWER-UP Testing Set User Passcode InitializationBoard-level tests Unit-level tests Set Control Port Chain In PCChain In/ Chain Out Normal POWER-UP Proced URE Installation Front Panel Peration ESU 120e Front Panel Layout 11 12 16 17 LED D escriptions CSU StatusSU/ D rop Status Module Status Operation keys Select and Activate a Menu Item General Menu Operation NI Perf Rpts NI Errors 4VIEW History END of ListPort Status Remote Port Clear Port ALM Enet Status Ata Port Identification Front Panel Menu StructureExit Any Menu Field Operation Or D isplay Watch PRO AD Tran PC Program Alternate Methods of Control Step Action Telnet Terminal Mode Status Menu Network Interface Performance Report Network Interface Performance Reports NI Perf Rpts Active Alarms Network Interface Errors NI Errors View History D isplay of Alarm Messages Port Rate Port StatusNx56/ 64 Menu Items D TE D ata/ CK TE Status Enet Status Clear Port AlarmRop Menu Items D SX Errors Remote Port Configuration Menu Configuration Menu Tree Intface Network NINetwork NI Menu Items Menu Item Description From the NI. See ESU 120 Clock Sources on page 5-5 for more ESU 120e Clock Sources Network Timed Clock Source Network Timed D rop Timed Clock Source Base D rop Timed Base D TE Timed Internal Clock Source Internal Timing Normal CSU Normal CSU Timing May not be used as a terminal interface Unit Menu Slip Map Exchange Map Xchng Map In Use ABOFF D S0 Map D esignations TS0 Map a and TS0 Map B Copy a Temp Create TempIdle Apply Temp a Review MAPReview Temp Edit Temp Nx56/ 64 Port Configuration Port Config Menu Items Port Configuration Port Config DSR DataCTS DCD Rop Port Configuration Port Config Menu Items Normal Mode of Operation Configuration Menu Utility Menu Enter Passcode from Other Menus Factory RestoreTime/ D ate Set Passcode Special Feature Change/ Set a PasscodeNo Passcode D esired No Unit ID D esired Unit IDSoftware Revision Software Rev To Set the Unit Identification CMD Mode Port UtilityEnet Address Utility Menu Test Menu Network Tests Loopback TestsNetwork Interface Loopbacks All Zeros Line On Activates the line loopbackBCK All Ones Qrss always runs at 64K/TS0 Qrss Pattern BES SESSync Run Self-Test Test Name What it does Port Tests Patt Port Test Menu Items for 0.1 Nx56PRT/LCL Remote Port Test Menu Items for 0.2 D rop Loopback Cancel Tests Test Menu Telnet/ Terminal Main Menu Main Menu TS0 Maps Configuration Menu Status, Config, Util, and Test Menu Options Reviewing Temp Maps Initializing the Temp MapEditing the Temp Map Applying the Temp Map Snmp Read/ Write Community Remote Menu AccessManagement Configuration Snmp Read Community Snmp Trap Community Poll Link Status Traps Sent Telnet/ Terminal TimeoutTelnet/ Terminal Password Auth. Fail Traps Sent Quit Session Flash D ownload Telnet/Terminal Menus Snmp Basic Components Network ManagerAgent GetNextRequest Command SMIB GetRequest Trap ESU 120E Snmp AccessMessages GetResponse Snmp Trap Configuration Snmp MIB Files Snmp MIB Browser Configuration Ppendix a . Understanding Snmp Table B-1. Network Pinouts WiringNetwork interface Connector Connector type 15-pin female D connector Pin Name Description Connector type RJ-48 Part Number AMP#Control In/ Chain Table B-2. Control In/ Chain-in Pinout Table B-3. Chain-Out Connector Pinout Chain OutConnections Pin Connector type Pin female D connectorAta Port Interface Table B-4. Nx56/ 64 Pin Assignments for EIA-530 Ccitt Table B-5. Nx56/ 64 Pin Assignments for V.35 Mode 1200285L1 DB25P Pin 34 Pin Name Table B-6. Adapter Cable, D B 25 to V.35, 34-Pin Winchester Pin Name Description Source Table B-7. Nx56/ 64 Pin Assignments for V.11/ x.21 Mode Name DB25Pin DA15S Pin Table B-8. Adapter Cable D B25 to X.21, D B15 ConnectorTable B-9. Pinout Connectors for Terminal Interface Base D rop PBX Pin Name To Nic Connector type Shielded RJ48 USOCPart Number AMP #10BaseT Table B-10 BaseT Pinout Ppendix B. Connector Pinouts Network Interface NI Alarm Messages Nx56/ 64 Interface Rop Port Interface Status Messages Network Interface NINx56/ 64 Interface HDB3 Electrical SpecificationsNetwork Interface CRC-4, FAS,CAS Rop Port Interface Nx56/ 64 D rop Port InterfaceNx56/ 64 V.35 Interface CTS, DCD, DSR Option Slot Interface Management InterfacesChain In/ Out Ports Watch Environmental Specifications Chassis Specifications Index NI Errors Snmptrap Configuration A-4 Index-4 Presales Inquiries and Applications Support Post-Sale SupportRepair and Return