Set Control Port, Chain In PC | ADTRAN ESU 120e specification

Chapter 2. Installation

Set Control Port

The ESU 120e can be configured from the control port when T- Watch PRO, SNMP, or the terminal interface are being used.

If the control port is to be used, the control port baud rate must also be selected.

Chain In (PC)

The unit can be controlled from an external PC connected directly or via modem to the chain-in port. when using chain-in, the selec- tion of the control port baud rate from 9600 (factory default), 1200, 2400, or 4800, or 38400 must be made using the Unit Configuration menu. See Unit Menu on page 5-11 for details.

Unless locked out externally, the front panel can also control the unit.

Chain In/ Chain Out

ESU 120e units and other ESUs can be linked together to form a chain. Figure 2-4 shows an example of a chain-in arrangement with a PC or a modem. The first ESU 120e in the chain receives control- ling input from the PC or modem.

PC or Modem

Control Chain

Input Out

ESU 120e

Chain Chain

In Out

ESU 120e

Chain Chain

In Out

ESU 120e

Figure 2-3. Example of Chain In

2-8

ESU 120e User Manual

61200420L1-1

Image 32

ADTRAN ESU 120e user manual Set Control Port, Chain In PC, Chain In/ Chain Out

Contents

ESU 120e Part Number 1200420L1-1 Trademarks Mail Adtran Web Site Product Matrix Faxback Document LineY2K Project Line Page Canadian Emissions Requirements Canadian Equipment Limitations Vii Important Safety Instructions Warranty and Customer Service Page Table of Contents Chapter Status Menu Chapter OperationSnmp Chapter Configuration Menu Chapter Utility MenuChapter Test Menu Local Loopbck Remote Loopbck Test Pattern Pattern Result LoopbkDIS 511 Reslt Telnet/Terminal Menus Appendix A. Understanding Snmp Index-1 Xvi 61200420L1-1 List of Figures List of Figures List of Tables List of Tables Introduction ESU 120E Overview ESU 120e Features ESU Option Modules Router, PBX Application ESU 120E Configuration ApplicationsOption Module Architecture Introduction UNPACK, INSPECT, Power UP Receipt InspectionAD Tran Shipments Include Customer Provides Power Connection Ground ING Instructions Installation ID Entification of Rear Panel Layout ESU 120e Rear Panel ESU120E Interfaces Network InterfacesNetwork Test Interface Nx56/ 64 Serial Interface POWER-UP Testing Self-Test Initialization Board-level testsUnit-level tests Set User Passcode Chain In/ Chain Out Set Control PortChain In PC Normal POWER-UP Proced URE Installation Peration Front Panel 11 12 16 17 ESU 120e Front Panel Layout SU/ D rop Status LED D escriptionsCSU Status Operation keys Module Status General Menu Operation Select and Activate a Menu Item Port Status Remote Port Clear Port ALM Enet Status NI Perf Rpts NI Errors4VIEW History END of List Exit Any Menu Field Operation Or D isplay Ata Port IdentificationFront Panel Menu Structure Alternate Methods of Control Watch PRO AD Tran PC Program Step Action Terminal Mode Telnet Status Menu Network Interface Performance Reports NI Perf Rpts Network Interface Performance Report Network Interface Errors NI Errors Active Alarms D isplay of Alarm Messages View History Port Status Nx56/ 64 Menu Items D TE D ata/ CKTE Status Port Rate Clear Port Alarm Rop Menu Items D SX ErrorsRemote Port Enet Status Configuration Menu Configuration Menu Tree Network NI Network NI Menu ItemsMenu Item Description Intface From the NI. See ESU 120 Clock Sources on page 5-5 for more ESU 120e Clock Sources Network Timed Network Timed Clock Source Base D rop Timed D rop Timed Clock Source Base D TE Timed Internal Timing Internal Clock Source Normal CSU Timing Normal CSU Unit Menu May not be used as a terminal interface Slip OFF Map Exchange Map XchngMap In Use AB TS0 Map a and TS0 Map B D S0 Map D esignations Idle Copy a TempCreate Temp Review MAP Review TempEdit Temp Apply Temp a Port Configuration Port Config Nx56/ 64 Port Configuration Port Config Menu Items Data CTSDCD DSR Normal Mode of Operation Rop Port Configuration Port Config Menu Items Configuration Menu Utility Menu Factory Restore Time/ D ateSet Passcode Enter Passcode from Other Menus No Passcode D esired Special FeatureChange/ Set a Passcode Unit ID Software Revision Software RevTo Set the Unit Identification No Unit ID D esired Enet Address CMD ModePort Utility Utility Menu Test Menu Network Interface Loopbacks Network TestsLoopback Tests Line On Activates the line loopback BCKAll Ones All Zeros Qrss Pattern Qrss always runs at 64K/TS0 Sync BESSES Run Self-Test Port Tests Test Name What it does Port Test Menu Items for 0.1 Nx56 PRT/LCLRemote Patt Cancel Tests Port Test Menu Items for 0.2 D rop Loopback Test Menu Main Menu Telnet/ Terminal Main Menu Status, Config, Util, and Test Menu Options TS0 Maps Configuration Menu Initializing the Temp Map Editing the Temp MapApplying the Temp Map Reviewing Temp Maps Remote Menu Access Management ConfigurationSnmp Read Community Snmp Read/ Write Community Snmp Trap Community Telnet/ Terminal Timeout Telnet/ Terminal PasswordAuth. Fail Traps Sent Poll Link Status Traps Sent Flash D ownload Quit Session Telnet/Terminal Menus Agent Snmp Basic ComponentsNetwork Manager Command S MIBGetRequest GetNextRequest ESU 120E Snmp Access MessagesGetResponse Trap Snmp Trap Configuration Snmp MIB Browser Configuration Snmp MIB Files Ppendix a . Understanding Snmp Wiring Network interface ConnectorConnector type 15-pin female D connector Table B-1. Network Pinouts Connector type RJ-48 Part Number AMP# Control In/ ChainTable B-2. Control In/ Chain-in Pinout Pin Name Description Connections Table B-3. Chain-Out Connector PinoutChain Out Connector type Pin female D connector Ata Port InterfaceTable B-4. Nx56/ 64 Pin Assignments for EIA-530 Pin Table B-5. Nx56/ 64 Pin Assignments for V.35 Mode Ccitt Table B-6. Adapter Cable, D B 25 to V.35, 34-Pin Winchester 1200285L1 DB25P Pin 34 Pin Name Table B-7. Nx56/ 64 Pin Assignments for V.11/ x.21 Mode Pin Name Description Source Table B-8. Adapter Cable D B25 to X.21, D B15 Connector Table B-9. Pinout Connectors for Terminal InterfaceBase D rop PBX Name DB25Pin DA15S Pin Connector type Shielded RJ48 USOCPart Number AMP # 10BaseTTable B-10 BaseT Pinout Pin Name To Nic Ppendix B. Connector Pinouts Alarm Messages Network Interface NI Nx56/ 64 Interface Rop Port Interface Nx56/ 64 Interface Status MessagesNetwork Interface NI Electrical Specifications Network InterfaceCRC-4, FAS,CAS HDB3 Nx56/ 64 D rop Port Interface Nx56/ 64 V.35 InterfaceCTS, DCD, DSR Rop Port Interface Management Interfaces Chain In/ Out PortsWatch Option Slot Interface Chassis Specifications Environmental Specifications Index NI Errors Snmptrap Configuration A-4 Index-4 Repair and Return Presales Inquiries and Applications SupportPost-Sale Support