Manuals / ADTRAN / Computer Equipment / Network Card

ADTRAN ESU 120e user manual Installation

Models: ESU 120e

1 124

Download 124 pages 62.06 Kb

Page 27

Chapter 2. Installation

Code, ANSI/NFPA 70. Termination of the supplementary equip- ment grounding conductor is permitted to be made to building steel, to a metal electrical raceway system, or to any grounded item that is permanently and reliably connected to the electrical service equipment ground.

Bare, covered, or insulated grounding conductors are acceptable. A covered or insulated grounding conductor shall have a continuous outer finish that is either green, or green with one or more yellow stripes.

The supplemental grounding conductor shall be connected to he equipment using a number 8 ring terminal. The terminal should be fastened to the grounding lug provided on the rear panel of the equipment. The ring terminal should be installed using the appro- priate crimping tool (AMP P/N 59250 T-EAD Crimping Tool or equivalent).

61200420L1-1

ESU 120e User Manual

2-3

Image 27

ADTRAN ESU 120e user manual Installation

Contents

Part Number 1200420L1-1 ESU 120eTrademarks Adtran Web Site Product Matrix Faxback Document Line Y2K Project LineMail Page Canadian Emissions Requirements Canadian Equipment Limitations Vii Important Safety Instructions Warranty and Customer Service Page Table of Contents Chapter Operation SnmpChapter Status Menu Local Loopbck Remote Loopbck Test Pattern Chapter Configuration MenuChapter Utility Menu Chapter Test MenuTelnet/Terminal Menus Pattern ResultLoopbk DIS 511 ResltIndex-1 Appendix A. Understanding SnmpXvi 61200420L1-1 List of Figures List of Figures List of Tables List of Tables ESU 120E Overview IntroductionESU Option Modules ESU 120e FeaturesESU 120E Configuration Applications Option Module ArchitectureRouter, PBX Application Introduction Customer Provides UNPACK, INSPECT, Power UPReceipt Inspection AD Tran Shipments IncludeGround ING Instructions Power ConnectionInstallation ESU 120e Rear Panel ID Entification of Rear Panel LayoutNx56/ 64 Serial Interface ESU120E InterfacesNetwork Interfaces Network Test InterfaceSelf-Test POWER-UP TestingSet User Passcode InitializationBoard-level tests Unit-level testsSet Control Port Chain In PCChain In/ Chain Out Normal POWER-UP Proced URE Installation Front Panel PerationESU 120e Front Panel Layout 11 12 16 17LED D escriptions CSU StatusSU/ D rop Status Module Status Operation keysSelect and Activate a Menu Item General Menu OperationNI Perf Rpts NI Errors 4VIEW History END of ListPort Status Remote Port Clear Port ALM Enet Status Ata Port Identification Front Panel Menu StructureExit Any Menu Field Operation Or D isplay Watch PRO AD Tran PC Program Alternate Methods of ControlStep Action Telnet Terminal ModeStatus Menu Network Interface Performance Report Network Interface Performance Reports NI Perf RptsActive Alarms Network Interface Errors NI ErrorsView History D isplay of Alarm MessagesPort Rate Port StatusNx56/ 64 Menu Items D TE D ata/ CK TE StatusEnet Status Clear Port AlarmRop Menu Items D SX Errors Remote PortConfiguration Menu Configuration Menu Tree Intface Network NINetwork NI Menu Items Menu Item DescriptionFrom the NI. See ESU 120 Clock Sources on page 5-5 for more ESU 120e Clock Sources Network Timed Clock Source Network TimedD rop Timed Clock Source Base D rop TimedBase D TE Timed Internal Clock Source Internal TimingNormal CSU Normal CSU TimingMay not be used as a terminal interface Unit MenuSlip Map Exchange Map Xchng Map In Use ABOFF D S0 Map D esignations TS0 Map a and TS0 Map BCopy a Temp Create TempIdle Apply Temp a Review MAPReview Temp Edit TempNx56/ 64 Port Configuration Port Config Menu Items Port Configuration Port ConfigDSR DataCTS DCDRop Port Configuration Port Config Menu Items Normal Mode of OperationConfiguration Menu Utility Menu Enter Passcode from Other Menus Factory RestoreTime/ D ate Set PasscodeSpecial Feature Change/ Set a PasscodeNo Passcode D esired No Unit ID D esired Unit IDSoftware Revision Software Rev To Set the Unit IdentificationCMD Mode Port UtilityEnet Address Utility Menu Test Menu Network Tests Loopback TestsNetwork Interface Loopbacks All Zeros Line On Activates the line loopbackBCK All OnesQrss always runs at 64K/TS0 Qrss PatternBES SESSync Run Self-Test Test Name What it does Port TestsPatt Port Test Menu Items for 0.1 Nx56PRT/LCL RemotePort Test Menu Items for 0.2 D rop Loopback Cancel TestsTest Menu Telnet/ Terminal Main Menu Main MenuTS0 Maps Configuration Menu Status, Config, Util, and Test Menu OptionsReviewing Temp Maps Initializing the Temp MapEditing the Temp Map Applying the Temp MapSnmp Read/ Write Community Remote Menu AccessManagement Configuration Snmp Read CommunitySnmp Trap Community Poll Link Status Traps Sent Telnet/ Terminal TimeoutTelnet/ Terminal Password Auth. Fail Traps SentQuit Session Flash D ownloadTelnet/Terminal Menus Snmp Basic Components Network ManagerAgent GetNextRequest Command SMIB GetRequestTrap ESU 120E Snmp AccessMessages GetResponseSnmp Trap Configuration Snmp MIB Files Snmp MIB Browser ConfigurationPpendix a . Understanding Snmp Table B-1. Network Pinouts WiringNetwork interface Connector Connector type 15-pin female D connectorPin Name Description Connector type RJ-48 Part Number AMP#Control In/ Chain Table B-2. Control In/ Chain-in PinoutTable B-3. Chain-Out Connector Pinout Chain OutConnections Pin Connector type Pin female D connectorAta Port Interface Table B-4. Nx56/ 64 Pin Assignments for EIA-530Ccitt Table B-5. Nx56/ 64 Pin Assignments for V.35 Mode1200285L1 DB25P Pin 34 Pin Name Table B-6. Adapter Cable, D B 25 to V.35, 34-Pin WinchesterPin Name Description Source Table B-7. Nx56/ 64 Pin Assignments for V.11/ x.21 ModeName DB25Pin DA15S Pin Table B-8. Adapter Cable D B25 to X.21, D B15 ConnectorTable B-9. Pinout Connectors for Terminal Interface Base D rop PBXPin Name To Nic Connector type Shielded RJ48 USOCPart Number AMP #10BaseT Table B-10 BaseT PinoutPpendix B. Connector Pinouts Network Interface NI Alarm MessagesNx56/ 64 Interface Rop Port Interface Status Messages Network Interface NINx56/ 64 Interface HDB3 Electrical SpecificationsNetwork Interface CRC-4, FAS,CASRop Port Interface Nx56/ 64 D rop Port InterfaceNx56/ 64 V.35 Interface CTS, DCD, DSROption Slot Interface Management InterfacesChain In/ Out Ports WatchEnvironmental Specifications Chassis SpecificationsIndex NI Errors Snmptrap Configuration A-4 Index-4 Presales Inquiries and Applications Support Post-Sale SupportRepair and Return