Unit ID, Software Revision Software Rev | ADTRAN ESU 120e guide

Chapter 6. Utility Menu

Unit ID

This menu is used to access the current Unit ID setting. Viewing is available in limited access mode. Editing or changing the Unit ID requires the use of a password as in editing mode. Unit Identifica- tion numbers must be between 2 and 250. If an out-of-range num- ber is entered, the unit assumes the upper limit number of 250.

To Set the Unit Identification

In the Unit ID menu (item 4) under the UTIL menu, enter any value between 2 and 250. The number 1 is reserved for the PC.

Pressing Enter records the Unit ID number and establishes its avail- ability for operation by remote control. The unit proceeds to the Set Control Port prompt.

No Unit ID D esired

Without entering any numbers at the Unit ID prompt, press Enter. Pressing Enter with no Unit ID recorded establishes the unit as not able to be operated by remote control.

Software Revision (Software Rev)

This menu provides access to the display of the current software revision level loaded into the base unit controller. This information is required when requesting assistance from ADTRAN Customer Service or when updates are needed.

Use Cancel to exit.

6-4

ESU 120e User Manual

61200420L1-1

Image 74

ADTRAN ESU 120e user manual Software Revision Software Rev, To Set the Unit Identification, No Unit ID D esired

Contents

ESU 120e Part Number 1200420L1-1 Trademarks Mail Adtran Web Site Product Matrix Faxback Document LineY2K Project Line Page Canadian Emissions Requirements Canadian Equipment Limitations Vii Important Safety Instructions Warranty and Customer Service Page Table of Contents Chapter Status Menu Chapter OperationSnmp Chapter Test Menu Chapter Configuration MenuChapter Utility Menu Local Loopbck Remote Loopbck Test Pattern DIS 511 Reslt Pattern ResultLoopbk Telnet/Terminal Menus Appendix A. Understanding Snmp Index-1 Xvi 61200420L1-1 List of Figures List of Figures List of Tables List of Tables Introduction ESU 120E Overview ESU 120e Features ESU Option Modules Router, PBX Application ESU 120E Configuration ApplicationsOption Module Architecture Introduction AD Tran Shipments Include UNPACK, INSPECT, Power UPReceipt Inspection Customer Provides Power Connection Ground ING Instructions Installation ID Entification of Rear Panel Layout ESU 120e Rear Panel Network Test Interface ESU120E InterfacesNetwork Interfaces Nx56/ 64 Serial Interface POWER-UP Testing Self-Test Unit-level tests InitializationBoard-level tests Set User Passcode Chain In/ Chain Out Set Control PortChain In PC Normal POWER-UP Proced URE Installation Peration Front Panel 11 12 16 17 ESU 120e Front Panel Layout SU/ D rop Status LED D escriptionsCSU Status Operation keys Module Status General Menu Operation Select and Activate a Menu Item Port Status Remote Port Clear Port ALM Enet Status NI Perf Rpts NI Errors4VIEW History END of List Exit Any Menu Field Operation Or D isplay Ata Port IdentificationFront Panel Menu Structure Alternate Methods of Control Watch PRO AD Tran PC Program Step Action Terminal Mode Telnet Status Menu Network Interface Performance Reports NI Perf Rpts Network Interface Performance Report Network Interface Errors NI Errors Active Alarms D isplay of Alarm Messages View History TE Status Port StatusNx56/ 64 Menu Items D TE D ata/ CK Port Rate Remote Port Clear Port AlarmRop Menu Items D SX Errors Enet Status Configuration Menu Configuration Menu Tree Menu Item Description Network NINetwork NI Menu Items Intface From the NI. See ESU 120 Clock Sources on page 5-5 for more ESU 120e Clock Sources Network Timed Network Timed Clock Source Base D rop Timed D rop Timed Clock Source Base D TE Timed Internal Timing Internal Clock Source Normal CSU Timing Normal CSU Unit Menu May not be used as a terminal interface Slip OFF Map Exchange Map XchngMap In Use AB TS0 Map a and TS0 Map B D S0 Map D esignations Idle Copy a TempCreate Temp Edit Temp Review MAPReview Temp Apply Temp a Port Configuration Port Config Nx56/ 64 Port Configuration Port Config Menu Items DCD DataCTS DSR Normal Mode of Operation Rop Port Configuration Port Config Menu Items Configuration Menu Utility Menu Set Passcode Factory RestoreTime/ D ate Enter Passcode from Other Menus No Passcode D esired Special FeatureChange/ Set a Passcode To Set the Unit Identification Unit IDSoftware Revision Software Rev No Unit ID D esired Enet Address CMD ModePort Utility Utility Menu Test Menu Network Interface Loopbacks Network TestsLoopback Tests All Ones Line On Activates the line loopbackBCK All Zeros Qrss Pattern Qrss always runs at 64K/TS0 Sync BESSES Run Self-Test Port Tests Test Name What it does Remote Port Test Menu Items for 0.1 Nx56PRT/LCL Patt Cancel Tests Port Test Menu Items for 0.2 D rop Loopback Test Menu Main Menu Telnet/ Terminal Main Menu Status, Config, Util, and Test Menu Options TS0 Maps Configuration Menu Applying the Temp Map Initializing the Temp MapEditing the Temp Map Reviewing Temp Maps Snmp Read Community Remote Menu AccessManagement Configuration Snmp Read/ Write Community Snmp Trap Community Auth. Fail Traps Sent Telnet/ Terminal TimeoutTelnet/ Terminal Password Poll Link Status Traps Sent Flash D ownload Quit Session Telnet/Terminal Menus Agent Snmp Basic ComponentsNetwork Manager GetRequest Command SMIB GetNextRequest GetResponse ESU 120E Snmp AccessMessages Trap Snmp Trap Configuration Snmp MIB Browser Configuration Snmp MIB Files Ppendix a . Understanding Snmp Connector type 15-pin female D connector WiringNetwork interface Connector Table B-1. Network Pinouts Table B-2. Control In/ Chain-in Pinout Connector type RJ-48 Part Number AMP#Control In/ Chain Pin Name Description Connections Table B-3. Chain-Out Connector PinoutChain Out Table B-4. Nx56/ 64 Pin Assignments for EIA-530 Connector type Pin female D connectorAta Port Interface Pin Table B-5. Nx56/ 64 Pin Assignments for V.35 Mode Ccitt Table B-6. Adapter Cable, D B 25 to V.35, 34-Pin Winchester 1200285L1 DB25P Pin 34 Pin Name Table B-7. Nx56/ 64 Pin Assignments for V.11/ x.21 Mode Pin Name Description Source Base D rop PBX Table B-8. Adapter Cable D B25 to X.21, D B15 ConnectorTable B-9. Pinout Connectors for Terminal Interface Name DB25Pin DA15S Pin Table B-10 BaseT Pinout Connector type Shielded RJ48 USOCPart Number AMP #10BaseT Pin Name To Nic Ppendix B. Connector Pinouts Alarm Messages Network Interface NI Nx56/ 64 Interface Rop Port Interface Nx56/ 64 Interface Status MessagesNetwork Interface NI CRC-4, FAS,CAS Electrical SpecificationsNetwork Interface HDB3 CTS, DCD, DSR Nx56/ 64 D rop Port InterfaceNx56/ 64 V.35 Interface Rop Port Interface Watch Management InterfacesChain In/ Out Ports Option Slot Interface Chassis Specifications Environmental Specifications Index NI Errors Snmptrap Configuration A-4 Index-4 Repair and Return Presales Inquiries and Applications SupportPost-Sale Support