LED D escriptions, CSU Status, SU/ D rop Status | ADTRAN ESU 120e

Chapter 3. O peration

LED D escriptions

CSU Status

The CSU status LEDs display the operational condition of the network interface located on the controller board in the unit.

Name	Description

OK (green)	Indicates the operation is in the normal mode and no
	errors have been detected.

Test (yellow)	Indicates that the network interface is operating in a test
	mode. This includes a self-test or a test loopback.
	When lighted, this LED also indicates that normal data
	flow is not occurring on the network interface.

Error (red)	Indicates an error such as a BPV, OOF, or CRC.

Alarm (red)	Indicates an alarm condition has been detected. When
	the alarm condition is no longer valid, the OK LED
	activates (turns on). To view an alarm condition, select
	the active alarm menu item or select Alarm by pressing
	Shift 8. If the alarm conditions have been corrected, the
	alarm which caused the activation of the Alarm LED
	can be viewed under the Unit History menu.

D SU/ D rop Status

Name	Description

OK (green)	Indicates the operation is in the normal mode and no
	errors have been detected.

Test (yellow)	Indicates that the interface is operating in a test mode.
	This includes a self-test or a test loopback. When
	lighted, this LED also indicates that normal data flow is
	not occurring in at least one of the module ports.

Alarm (red)	Indicates an alarm condition has been detected. When
	the alarm condition is no longer valid, the OK LED
	activates (turns on). To view an alarm condition, select
	the active alarm menu item or select Alarm by pressing
	Shift 8. If the alarm conditions have been corrected, the
	alarm which caused the activation of the Alarm LED
	can be viewed under the Unit History menu.

61200420L1-1

ESU 120e User Manual

3-3

Image 37

ADTRAN ESU 120e user manual LED D escriptions, CSU Status, SU/ D rop Status

Contents

Part Number 1200420L1-1 ESU 120e Trademarks Y2K Project Line Adtran Web Site Product Matrix Faxback Document LineMail Page Canadian Emissions Requirements Canadian Equipment Limitations Vii Important Safety Instructions Warranty and Customer Service Page Table of Contents Snmp Chapter OperationChapter Status Menu Chapter Utility Menu Chapter Configuration MenuChapter Test Menu Local Loopbck Remote Loopbck Test Pattern Loopbk Pattern ResultDIS 511 Reslt Telnet/Terminal Menus Index-1 Appendix A. Understanding Snmp Xvi 61200420L1-1 List of Figures List of Figures List of Tables List of Tables ESU 120E Overview Introduction ESU Option Modules ESU 120e Features Option Module Architecture ESU 120E Configuration ApplicationsRouter, PBX Application Introduction Receipt Inspection UNPACK, INSPECT, Power UPAD Tran Shipments Include Customer Provides Ground ING Instructions Power Connection Installation ESU 120e Rear Panel ID Entification of Rear Panel Layout Network Interfaces ESU120E InterfacesNetwork Test Interface Nx56/ 64 Serial Interface Self-Test POWER-UP Testing Board-level tests InitializationUnit-level tests Set User Passcode Chain In PC Set Control PortChain In/ Chain Out Normal POWER-UP Proced URE Installation Front Panel Peration ESU 120e Front Panel Layout 11 12 16 17 CSU Status LED D escriptionsSU/ D rop Status Module Status Operation keys Select and Activate a Menu Item General Menu Operation 4VIEW History END of List NI Perf Rpts NI ErrorsPort Status Remote Port Clear Port ALM Enet Status Front Panel Menu Structure Ata Port IdentificationExit Any Menu Field Operation Or D isplay Watch PRO AD Tran PC Program Alternate Methods of Control Step Action Telnet Terminal Mode Status Menu Network Interface Performance Report Network Interface Performance Reports NI Perf Rpts Active Alarms Network Interface Errors NI Errors View History D isplay of Alarm Messages Nx56/ 64 Menu Items D TE D ata/ CK Port StatusTE Status Port Rate Rop Menu Items D SX Errors Clear Port AlarmRemote Port Enet Status Configuration Menu Configuration Menu Tree Network NI Menu Items Network NIMenu Item Description Intface From the NI. See ESU 120 Clock Sources on page 5-5 for more ESU 120e Clock Sources Network Timed Clock Source Network Timed D rop Timed Clock Source Base D rop Timed Base D TE Timed Internal Clock Source Internal Timing Normal CSU Normal CSU Timing May not be used as a terminal interface Unit Menu Slip Map In Use AB Map Exchange Map XchngOFF D S0 Map D esignations TS0 Map a and TS0 Map B Create Temp Copy a TempIdle Review Temp Review MAPEdit Temp Apply Temp a Nx56/ 64 Port Configuration Port Config Menu Items Port Configuration Port Config CTS DataDCD DSR Rop Port Configuration Port Config Menu Items Normal Mode of Operation Configuration Menu Utility Menu Time/ D ate Factory RestoreSet Passcode Enter Passcode from Other Menus Change/ Set a Passcode Special FeatureNo Passcode D esired Software Revision Software Rev Unit IDTo Set the Unit Identification No Unit ID D esired Port Utility CMD ModeEnet Address Utility Menu Test Menu Loopback Tests Network TestsNetwork Interface Loopbacks BCK Line On Activates the line loopbackAll Ones All Zeros Qrss always runs at 64K/TS0 Qrss Pattern SES BESSync Run Self-Test Test Name What it does Port Tests PRT/LCL Port Test Menu Items for 0.1 Nx56Remote Patt Port Test Menu Items for 0.2 D rop Loopback Cancel Tests Test Menu Telnet/ Terminal Main Menu Main Menu TS0 Maps Configuration Menu Status, Config, Util, and Test Menu Options Editing the Temp Map Initializing the Temp MapApplying the Temp Map Reviewing Temp Maps Management Configuration Remote Menu AccessSnmp Read Community Snmp Read/ Write Community Snmp Trap Community Telnet/ Terminal Password Telnet/ Terminal TimeoutAuth. Fail Traps Sent Poll Link Status Traps Sent Quit Session Flash D ownload Telnet/Terminal Menus Network Manager Snmp Basic ComponentsAgent MIB Command SGetRequest GetNextRequest Messages ESU 120E Snmp AccessGetResponse Trap Snmp Trap Configuration Snmp MIB Files Snmp MIB Browser Configuration Ppendix a . Understanding Snmp Network interface Connector WiringConnector type 15-pin female D connector Table B-1. Network Pinouts Control In/ Chain Connector type RJ-48 Part Number AMP#Table B-2. Control In/ Chain-in Pinout Pin Name Description Chain Out Table B-3. Chain-Out Connector PinoutConnections Ata Port Interface Connector type Pin female D connectorTable B-4. Nx56/ 64 Pin Assignments for EIA-530 Pin Ccitt Table B-5. Nx56/ 64 Pin Assignments for V.35 Mode 1200285L1 DB25P Pin 34 Pin Name Table B-6. Adapter Cable, D B 25 to V.35, 34-Pin Winchester Pin Name Description Source Table B-7. Nx56/ 64 Pin Assignments for V.11/ x.21 Mode Table B-9. Pinout Connectors for Terminal Interface Table B-8. Adapter Cable D B25 to X.21, D B15 ConnectorBase D rop PBX Name DB25Pin DA15S Pin 10BaseT Connector type Shielded RJ48 USOCPart Number AMP #Table B-10 BaseT Pinout Pin Name To Nic Ppendix B. Connector Pinouts Network Interface NI Alarm Messages Nx56/ 64 Interface Rop Port Interface Network Interface NI Status MessagesNx56/ 64 Interface Network Interface Electrical SpecificationsCRC-4, FAS,CAS HDB3 Nx56/ 64 V.35 Interface Nx56/ 64 D rop Port InterfaceCTS, DCD, DSR Rop Port Interface Chain In/ Out Ports Management InterfacesWatch Option Slot Interface Environmental Specifications Chassis Specifications Index NI Errors Snmptrap Configuration A-4 Index-4 Post-Sale Support Presales Inquiries and Applications SupportRepair and Return