Base D rop Timed, D rop Timed Clock Source | ADTRAN ESU 120e

Chapter 5. Configuration Menu

Base D rop Timed

The PBX is the source of timing. The ESU 120e uses the clock derived by the Base Drop interface for transmission timing (see Fig- ure 5-3).

E1 XMIT

E1 Receive

			OSC

Network
Interface				( O P T I O N )
			Nx56/64	Drop Port
			Nx56/64	Drop Port
		DTE CLOCK

DTEPBX

Figure 5-3. D rop Timed Clock Source

61200420L1-1

ESU 120e User Manual

5-7

Image 57

ADTRAN ESU 120e user manual Base D rop Timed, D rop Timed Clock Source

Contents

Part Number 1200420L1-1 ESU 120e Trademarks Adtran Web Site Product Matrix Faxback Document Line Y2K Project LineMail Page Canadian Emissions Requirements Canadian Equipment Limitations Vii Important Safety Instructions Warranty and Customer Service Page Table of Contents Chapter Operation SnmpChapter Status Menu Chapter Utility Menu Chapter Configuration MenuChapter Test Menu Local Loopbck Remote Loopbck Test Pattern Loopbk Pattern ResultDIS 511 Reslt Telnet/Terminal Menus Index-1 Appendix A. Understanding Snmp Xvi 61200420L1-1 List of Figures List of Figures List of Tables List of Tables ESU 120E Overview Introduction ESU Option Modules ESU 120e Features ESU 120E Configuration Applications Option Module ArchitectureRouter, PBX Application Introduction Receipt Inspection UNPACK, INSPECT, Power UPAD Tran Shipments Include Customer Provides Ground ING Instructions Power Connection Installation ESU 120e Rear Panel ID Entification of Rear Panel Layout Network Interfaces ESU120E InterfacesNetwork Test Interface Nx56/ 64 Serial Interface Self-Test POWER-UP Testing Board-level tests InitializationUnit-level tests Set User Passcode Set Control Port Chain In PCChain In/ Chain Out Normal POWER-UP Proced URE Installation Front Panel Peration ESU 120e Front Panel Layout 11 12 16 17 LED D escriptions CSU StatusSU/ D rop Status Module Status Operation keys Select and Activate a Menu Item General Menu Operation NI Perf Rpts NI Errors 4VIEW History END of ListPort Status Remote Port Clear Port ALM Enet Status Ata Port Identification Front Panel Menu StructureExit Any Menu Field Operation Or D isplay Watch PRO AD Tran PC Program Alternate Methods of Control Step Action Telnet Terminal Mode Status Menu Network Interface Performance Report Network Interface Performance Reports NI Perf Rpts Active Alarms Network Interface Errors NI Errors View History D isplay of Alarm Messages Nx56/ 64 Menu Items D TE D ata/ CK Port StatusTE Status Port Rate Rop Menu Items D SX Errors Clear Port AlarmRemote Port Enet Status Configuration Menu Configuration Menu Tree Network NI Menu Items Network NIMenu Item Description Intface From the NI. See ESU 120 Clock Sources on page 5-5 for more ESU 120e Clock Sources Network Timed Clock Source Network Timed D rop Timed Clock Source Base D rop Timed Base D TE Timed Internal Clock Source Internal Timing Normal CSU Normal CSU Timing May not be used as a terminal interface Unit Menu Slip Map Exchange Map Xchng Map In Use ABOFF D S0 Map D esignations TS0 Map a and TS0 Map B Copy a Temp Create TempIdle Review Temp Review MAPEdit Temp Apply Temp a Nx56/ 64 Port Configuration Port Config Menu Items Port Configuration Port Config CTS DataDCD DSR Rop Port Configuration Port Config Menu Items Normal Mode of Operation Configuration Menu Utility Menu Time/ D ate Factory RestoreSet Passcode Enter Passcode from Other Menus Special Feature Change/ Set a PasscodeNo Passcode D esired Software Revision Software Rev Unit IDTo Set the Unit Identification No Unit ID D esired CMD Mode Port UtilityEnet Address Utility Menu Test Menu Network Tests Loopback TestsNetwork Interface Loopbacks BCK Line On Activates the line loopbackAll Ones All Zeros Qrss always runs at 64K/TS0 Qrss Pattern BES SESSync Run Self-Test Test Name What it does Port Tests PRT/LCL Port Test Menu Items for 0.1 Nx56Remote Patt Port Test Menu Items for 0.2 D rop Loopback Cancel Tests Test Menu Telnet/ Terminal Main Menu Main Menu TS0 Maps Configuration Menu Status, Config, Util, and Test Menu Options Editing the Temp Map Initializing the Temp MapApplying the Temp Map Reviewing Temp Maps Management Configuration Remote Menu AccessSnmp Read Community Snmp Read/ Write Community Snmp Trap Community Telnet/ Terminal Password Telnet/ Terminal TimeoutAuth. Fail Traps Sent Poll Link Status Traps Sent Quit Session Flash D ownload Telnet/Terminal Menus Snmp Basic Components Network ManagerAgent MIB Command SGetRequest GetNextRequest Messages ESU 120E Snmp AccessGetResponse Trap Snmp Trap Configuration Snmp MIB Files Snmp MIB Browser Configuration Ppendix a . Understanding Snmp Network interface Connector WiringConnector type 15-pin female D connector Table B-1. Network Pinouts Control In/ Chain Connector type RJ-48 Part Number AMP#Table B-2. Control In/ Chain-in Pinout Pin Name Description Table B-3. Chain-Out Connector Pinout Chain OutConnections Ata Port Interface Connector type Pin female D connectorTable B-4. Nx56/ 64 Pin Assignments for EIA-530 Pin Ccitt Table B-5. Nx56/ 64 Pin Assignments for V.35 Mode 1200285L1 DB25P Pin 34 Pin Name Table B-6. Adapter Cable, D B 25 to V.35, 34-Pin Winchester Pin Name Description Source Table B-7. Nx56/ 64 Pin Assignments for V.11/ x.21 Mode Table B-9. Pinout Connectors for Terminal Interface Table B-8. Adapter Cable D B25 to X.21, D B15 ConnectorBase D rop PBX Name DB25Pin DA15S Pin 10BaseT Connector type Shielded RJ48 USOCPart Number AMP #Table B-10 BaseT Pinout Pin Name To Nic Ppendix B. Connector Pinouts Network Interface NI Alarm Messages Nx56/ 64 Interface Rop Port Interface Status Messages Network Interface NINx56/ 64 Interface Network Interface Electrical SpecificationsCRC-4, FAS,CAS HDB3 Nx56/ 64 V.35 Interface Nx56/ 64 D rop Port InterfaceCTS, DCD, DSR Rop Port Interface Chain In/ Out Ports Management InterfacesWatch Option Slot Interface Environmental Specifications Chassis Specifications Index NI Errors Snmptrap Configuration A-4 Index-4 Presales Inquiries and Applications Support Post-Sale SupportRepair and Return