Manuals / APC / Computer Equipment / Power Supply

APC 3000 UPS Family Range and Components, 13.85in/352mm Enclosures, 20.59in/523mm Enclosures

Models: 3000

1 58

Download 58 pages 30.91 Kb

Page 11

UPS Family Range and Components

UPS Family Range and Components

13.85in/352mm Enclosures

Conduit

Box

www.apc.com

Front view	Rear view	Front view without cover
		10-15kVA

20.59in/523mm Enclosures

Blind plate covers any empty Power Module bay

Conduit	Blind plates
	cover

Box	any empty
	battery bays

	www.apc.com		Front view without cover
	Front view	Rear view
			10-15kVA

Front view without cover

20-30kVA

AIS® 3000 10-30kVA, 208V, Site Preparation and Installation Manual – 990-1957

3

Image 11

APC 3000 installation manual UPS Family Range and Components, 13.85in/352mm Enclosures, 20.59in/523mm Enclosures

Contents

10-30kVA 208V Site Preparation and Installation ManualPage AIS 3000 10-30kVA Site Preparation and Installation ManualIMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS followed during installation and maintenance of the UPS and batteriesPage Contents IntroductionSite Preparation UPS and XR Electrical Installation LIMITED FACTORY WARRANTY Communication Wiring to EPO and Optional EquipmentGeneral Charge Setting Wiring Verification Procedure Installation Site ChecklistPage Introduction General Safety Instructions 20.59in/523mm Enclosures UPS Family Range and Components13.85in/352mm Enclosures Introduction - UPS Family Range and Components System sizes, part nos., number of Battery Modules and weightsI S V T 1 0 K F 1 B 2 S Part number codingFront Panel overview Battery ModuleFront Panel attachment procedure described in the Front Panel section Conduit BoxStabilizing Bracket Service port for APC maintenance personnel only XR Enclosure weights OptionsExtended Run Battery Enclosure XR Enclosure and Battery Module Battery Module Part Number for Battery ModuleMaintenance Bypass Panels with Power Distribution Capability Battery Module weight29.53in/ 750mm Floor anchoring and battery securing equipmentBattery Securing Bracket MBP wall-mount 37.36in 949mmSpace requirements Installation Space RequirementsSite Preparation UPS and XR Clearance for 20.59in/523mm EnclosuresA Conduit Box F D G Site Preparation UPS and XR - Installation Space RequirementsB UPS XR C C E Stabilizing Bracket, left and right Site Preparation UPS and XR - Installation Space RequirementsClearance for stand-alone 13.85in/352mm Enclosures Space requirementsA Conduit Box F G Site Preparation UPS and XR - Installation Space RequirementsSpace requirements B UPS XR C2 C1 EFloor Anchoring Preparation Recommended floor bolt size 5/16in/8mm Audible noise Operating EnvironmentOperating conditions Heat dissipationSite Preparation UPS and XR - Operating Environment See also Recommended Wiring for a 86F 30C Temperature EnvironmentRecommended source connections The UPS must be supplied from a 208Y/120V 4W + GND 60Hz sourcecustomer Mains input Minimum setting of breakers for 10kVA UPSMinimum setting of breakers for 15kVA UPS OverloadMains input Minimum setting of breakers for 20kVA UPSMinimum setting of breakers for 30kVA UPS Overloadphase current Maintenance Bypass Panel Optional Equipment Basic Wiring OverviewAC input power DC power Communication Interface AC power outputArrival Preparation. Have you Site Preparation ChecklistSystem components. Have you Site Preparation. Have youFront Panel Electrical InstallationElectrical Installation - Front Panel InstallationUtility/Mains breaker Total-Power-Off ProcedureElectrical Installation - Total-Power-Off Procedure UPS ratings System-Electrical InformationSource connections Electrical Installation - System-Electrical InformationWiring bottom part Input/Output Wiring - Single Mains defaultConduit box Attach the Conduit Box bottom to the Enclosure, using 4 M4x13 screws Input/Output Wiring - Dual Mains Electrical Installation - Input/Output Wiring - Dual Mains Communication Wiring to EPO and Optional Equipment J108 Pin Connections Pin connections J106 XR Enclosure and J108 EPOPin connections J106 UPS to J200 XR Enclosure - option J106 Pin ConnectionsPins 7 and 8 are for external charge control Electrical Installation - Communication Wiring to EPO and Optional Pin connections J108 for EPO wiring optionsSee EPO wiring options for setup General Charge Setting Leveling Feet Floor anchoring of stand-alone systems Floor Anchoring optionElectrical Installation - Floor Anchoring option Battery securingMains Input Wiring Verification ProcedureBypass Input for dual mains installations 5 10. Reinstall all wiring access panels and Front Panels to the UPS Installation Site Checklist period LIMITED FACTORY WARRANTYExclusions Warranty claims procedureElectrical Installation - LIMITED FACTORY WARRANTY Drawings, descriptionsSERVICE IN CONNECTION WITH THE PRODUCTS. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE, CONSTITUTE SOLE LIABILITY OF APC AND YOUR EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. THE WARRANTIES EXTEND ONLY TO YOU AND ARE NOT EXTENDED TO ANY THIRD PARTIES 11/2004 990-1957APC Worldwide Customer Support 990-1957