Manuals / APC / Computer Equipment / Power Supply

APC 3000 Recommended source connections, Site Preparation UPS and XR - Operating Environment

Models: 3000

1 58

Download 58 pages 30.91 Kb

Page 26

Site Preparation (UPS and XR) – Operating Environment

Recommended source connections

The UPS must be supplied from a 208Y/120V 4W + GND 60Hz source.

CAUTION!

Verify clockwise phase-rotation (L1, L2, L3) and make sure a neutral connection is present.

See also Recommended Wiring for a 86°F (30°C) Temperature Environment.

18	AIS® 3000 10-30kVA, 208V, Site Preparation and Installation Manual – 990-1957

Image 26

APC 3000 installation manual Recommended source connections, The UPS must be supplied from a 208Y/120V 4W + GND 60Hz source

Contents

Site Preparation and Installation Manual 10-30kVA 208VPage followed during installation and maintenance of the UPS and batteries Site Preparation and Installation ManualIMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS AIS 3000 10-30kVAPage Contents IntroductionSite Preparation UPS and XR Electrical Installation Wiring Verification Procedure Installation Site Checklist Communication Wiring to EPO and Optional EquipmentGeneral Charge Setting LIMITED FACTORY WARRANTYPage Introduction General Safety Instructions 20.59in/523mm Enclosures UPS Family Range and Components13.85in/352mm Enclosures Part number coding System sizes, part nos., number of Battery Modules and weightsI S V T 1 0 K F 1 B 2 S Introduction - UPS Family Range and ComponentsConduit Box Battery ModuleFront Panel attachment procedure described in the Front Panel section Front Panel overviewStabilizing Bracket Service port for APC maintenance personnel only XR Enclosure weights OptionsExtended Run Battery Enclosure XR Enclosure and Battery Module Battery Module weight Part Number for Battery ModuleMaintenance Bypass Panels with Power Distribution Capability Battery ModuleMBP wall-mount 37.36in 949mm Floor anchoring and battery securing equipmentBattery Securing Bracket 29.53in/ 750mmClearance for 20.59in/523mm Enclosures Installation Space RequirementsSite Preparation UPS and XR Space requirementsA Conduit Box F D G Site Preparation UPS and XR - Installation Space RequirementsB UPS XR C C E Space requirements Site Preparation UPS and XR - Installation Space RequirementsClearance for stand-alone 13.85in/352mm Enclosures Stabilizing Bracket, left and rightB UPS XR C2 C1 E Site Preparation UPS and XR - Installation Space RequirementsSpace requirements A Conduit Box F GFloor Anchoring Preparation Recommended floor bolt size 5/16in/8mm Heat dissipation Operating EnvironmentOperating conditions Audible noiseThe UPS must be supplied from a 208Y/120V 4W + GND 60Hz source See also Recommended Wiring for a 86F 30C Temperature EnvironmentRecommended source connections Site Preparation UPS and XR - Operating Environmentcustomer Overload Minimum setting of breakers for 10kVA UPSMinimum setting of breakers for 15kVA UPS Mains inputOverload Minimum setting of breakers for 20kVA UPSMinimum setting of breakers for 30kVA UPS Mains inputphase current AC power output Basic Wiring OverviewAC input power DC power Communication Interface Maintenance Bypass Panel Optional EquipmentSite Preparation. Have you Site Preparation ChecklistSystem components. Have you Arrival Preparation. Have youElectrical Installation Front PanelInstallation Electrical Installation - Front PanelTotal-Power-Off Procedure Utility/Mains breakerElectrical Installation - Total-Power-Off Procedure System-Electrical Information UPS ratingsElectrical Installation - System-Electrical Information Source connectionsWiring bottom part Input/Output Wiring - Single Mains defaultConduit box Attach the Conduit Box bottom to the Enclosure, using 4 M4x13 screws Input/Output Wiring - Dual Mains Electrical Installation - Input/Output Wiring - Dual Mains Communication Wiring to EPO and Optional Equipment J106 Pin Connections Pin connections J106 XR Enclosure and J108 EPOPin connections J106 UPS to J200 XR Enclosure - option J108 Pin ConnectionsPins 7 and 8 are for external charge control Electrical Installation - Communication Wiring to EPO and Optional Pin connections J108 for EPO wiring optionsSee EPO wiring options for setup General Charge Setting Leveling Feet Floor Anchoring option Floor anchoring of stand-alone systemsBattery securing Electrical Installation - Floor Anchoring optionMains Input Wiring Verification ProcedureBypass Input for dual mains installations 5 10. Reinstall all wiring access panels and Front Panels to the UPS Installation Site Checklist LIMITED FACTORY WARRANTY periodDrawings, descriptions Warranty claims procedureElectrical Installation - LIMITED FACTORY WARRANTY ExclusionsSERVICE IN CONNECTION WITH THE PRODUCTS. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE, CONSTITUTE SOLE LIABILITY OF APC AND YOUR EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. THE WARRANTIES EXTEND ONLY TO YOU AND ARE NOT EXTENDED TO ANY THIRD PARTIES 990-1957 990-1957APC Worldwide Customer Support 11/2004