Manuals / Asante Technologies / Computer Equipment / Power Supply

Asante Technologies IC36240 Installing into an Equipment Rack, Recommended Installation Tools

Models: IC36240

1 108

Download 108 pages 14.72 Kb

Page 13

2.1.2 Recommended Installation Tools

You need the following additional tools and equipment to install the switch into an equipment rack:

•Flat head screwdriver

•Phillips head screwdriver

•Antistatic mat or foam

2.1.3 Power Requirements

The electrical outlet should be properly grounded, located near the switch and be easily accessible. Make sure the power source adheres to the following guidelines:

•Power: Auto Switching AC, 90-240 VAC

•Frequency range: 50/60 Hz

2.1.4 Environmental Requirements

Install the switch in a clean, dry, dust-free area with adequate air circulation to maintain the following environmental limits:

•Operating Temperature: 0° to 40°C (32° to 104°F)

•Relative Humidity: 5% to 95% non-condensing

Avoid direct sunlight, heat sources, or areas with high levels of electromagnetic interference. Failure to observe these limits may cause damage to the switch and void the warranty.

2.1.5 Cooling and Airflow

The IntraCore IC36240 switch uses internal fans for air-cooling. Do not restrict airflow by covering or obstructing air vents on the sides of the switch.

2.2 Installing into an Equipment Rack

Important: Before continuing, disconnect all cables from the switch.

To mount the switch into an equipment rack:

1.Place the switch on a flat, stable surface.

2.Locate a rack-mounting bracket (supplied) and place it over the mounting holes on one side of the switch.

3.Use the screws (supplied) to secure the bracket (with a Phillips screwdriver).

4.Repeat the two previous steps on the other side of the switch.

13

Asante IntraCore IC36240

User’s Manual

Image 13

Asante Technologies IC36240 Installing into an Equipment Rack, Recommended Installation Tools, Power Requirements

Contents

IntraCore IC36240 Series IntraCore IC36240 Layer 2+ Gigabit Ethernet Switch User’s ManualTable of Contents Password Service Password-Encryption Snmp Configuration Commands Trunk Ieee 802.1q Technical Support and Warranty Introduction FeaturesFront and Back Panel Descriptions Package ContentsLED LEDsConsole Interface Management and ConfigurationInstallation Overview Hardware Installation and SetupSafety Overview Recommended Installation Tools Installing into an Equipment RackPower Requirements Environmental RequirementsSFP Mini Gbic Ports Installing the Optional External Power SupplyEquipment Rack Guidelines Connecting to the Network Connecting Power1 10/100/1000BaseT Ports Cabling Procedures Pin Number Pair Number & Wire Colors Gigabit Ethernet Ports Cabling ProceduresAsante IntraCore IC36240 Connecting to a Console Initial Software SetupUser Access Verification Password Connecting to a PCPrivileges Commands Passwords and Privileges CommandsEnable Password Service Password-Encryption PasswordConfiguring an IP Address Login SecurityUsername Command Password and login CommandsSystem Boot Parameters Restoring Factory DefaultsSetting a Default IP Gateway Address Switchconfig# ip default-gatewayUser Top User Exec Mode Understanding the Command Line Interface CLIAccess Each Command Mode Document ConventionsCommand Show ? Purpose Privileged Top Privileged Exec ModeGlobal Configuration Mode Switch# configure Command Exit End Ctrl-Z PurposeSpanning-Tree Configuration Mode Interface Configuration ModeVlan Configuration Mode Advanced Features Supported within the Command ModeSpanning-tree mst configuration Example of Context Sensitive Help Command Help PurposeSwitch# configure ? Checking Command SyntaxUsing the No and Default Forms of Commands Using CLI Command HistoryUsing Command-Line Editing Features and Shortcuts Keystrokes/Command PurposeCompleting a Partial Command Name Moving Around on the Command LineKeystrokes Purpose Editing Command Lines That Wrap Deleting Entries Redisplaying the Current Command LineScrolling Down a Line or a Screen Controlling Capitalization Transposing Mistyped CharactersKeystrokes Setting the System Clock Managing the System and Configuration FilesSwitch# clock ? Switch# clock set 092930 28 January Switch# reload crTesting Connections with Ping Tests Changing the PasswordSpecifying the Hostname Enabling the System LogDisplaying the Operating Configuration Managing Configuration FilesConfiguring from the Terminal Switch# show running-configNewname# copy running-config startup-config Copying Configuration Files to a Network ServerSwitch# copy startup-config ? Switch# copy running-config Tftp Switch# copy running-configSwitch# copy running-config tftp//192.168.0.1/my-config Authentication Configuring SnmpAccess Control Switch# copy tftp//192.168.123.59/my-confg running-configSecurity Levels Create or Modify Access Control for Snmp CommunitySupport Establish the Contact and Location of the Snmp Agent Command Purpose Snmp-server community string viewSnmp Configuration Commands Configuring Spanning TreeSpanning-tree mst? Spanning Tree ParametersRapid Spanning Tree Protocol Rstp Spanning Tree Port ConfigurationPort Priority Port Path CostSwitchconfig# spanning-tree priority priority Configuring Switch/Bridge PriorityRapid Convergence Enabling Rapid Spanning TreeConfiguring an Edge Port Configuring Link TypeConfiguring Port Path Cost Configuring Port PriorityMultiple Spanning-Tree MST Vlan Configuring VlanMAC Address Table Switchconfig# mac-address-table aging-timeShow mac-address-table Assign IP Addresses to Switch Configuring IPClass Address or Range Status Define a Static ARP Cache Establish Address ResolutionManaging IP Multicast Traffic Configuring IgmpIgmp Overview Forwarding Unknown Multicast PacketsSwitchconfig-if-veth1#ip igmp query-interval Using Access ListsCommand Purpose Ip igmp query-max-response-time Host-query messagesUsing a Classification ACL Asante IntraCore IC36240 Create a Standard Access List Create an Expanded Access List Create a MAC Access ListSwitchconfig# mac access-list standard Access-list 101 deny ? Access-list 101 ?Access-list 101 deny tcp ? Access-list 101 deny tcp 192.168.123.0 0.0.0.255 ?Applying an Access List to an Interface Creating an Access List with a NameAccess-list ? Access-list standard ?Switchconfig# access-list 110 permit udp any any eq Configuring Common Access ListsAccess-list 101 deny ip any any Creating or Modifying a Vlan Vlan ConfigurationSwitchconfig-vlan#port-member delete eth Switch# show vlanDeleting a Vlan Vlan Port Membership Modes Static AccessTrunk Ieee 802.1q Switchconfig# end Command Purpose Switchconfig# vlan dot1q tag nativeConfiguring Weighted Fair Queuing Quality of Service ConfigurationMonitoring Weighted Fair Queuing Lists Priority QueuingTraffic Shaping Configuring Traffic Shaping for an InterfaceDefining the Priority List Monitoring Priority Queuing ListsConfiguring Traffic Shaping for an Access List Configuring Rate LimitMonitoring the Traffic Shaping Configuration Generic Traffic Shaping ExampleAsante IntraCore IC36240 Main Configuration Menu Configuring the Switch Using the GUIFront Panel Information Screen Information ScreensGeneral Information Screen Assign IP Addresses to SwitchClass Address or Range Status Individual Port Configuration Screen Port Configuration MenuAsante IntraCore IC36240 Press go Spanning Tree Protocol Configuration STP Port Configuration Global STP Bridge Configuration Snmp Configuration Asante IntraCore IC36240 Address Table Screen Asante IntraCore IC36240 Asante IntraCore IC36240 Vlan Configuration Asante IntraCore IC36240 Click Apply Igmp Configuration Asante IntraCore IC36240 Asante IntraCore IC36240 Web CLI Screen System Clock Menu Save Problem Possible Solutions Appendix a Basic TroubleshootingPhysical Characteristics Appendix B SpecificationsEnvironmental Range PerformanceStandards Compliance Technical Support and WarrantyFCC Compliance Statement Important Safety Instructions Appendix C FCC Compliance and Warranty StatementsIntraCare Warranty Statement Appendix D Online Warranty Registration Index Access ListIgmp LED Safety Priority Queuing Vlan