Asante IntraCore IC36240 | Asante Technologies guide

3. Click Apply	2	3
1

To configure a specific VLAN click on the VLAN ID number access the advanced IGMP configuration screen.

The following example shows the IGMP information for VLAN1.

Multicast switches send IGMP host-query messages to discover which multicast groups are present on attached networks. These messages are sent to the all-systems group address of 224.0.0.1 with a time-to-live (TTL) value of 1.

Multicast switches continue to periodically send host-query messages to refresh their knowledge of memberships present on their networks. If, after some number of queries, the switch software discovers that no local hosts are members of a multicast group, the software stops forwarding onto the local network multicast packets from remote origins for that group and sends a prune message upstream toward the source.

To enable or disable and to set the query intervals follow these steps.

1.Select enable or disable from the drop down menu

2.Enter the desired query interval (10-200)

94

Asante IntraCore IC36240

User’s Manual

Image 94

Asante Technologies user manual Asante IntraCore IC36240

Contents

IntraCore IC36240 Series Layer 2+ Gigabit Ethernet Switch User’s Manual IntraCore IC36240 Table of Contents Password Service Password-Encryption Snmp Configuration Commands Trunk Ieee 802.1q Technical Support and Warranty Features Introduction Package Contents Front and Back Panel Descriptions LEDs LED Management and Configuration Console Interface Installation Overview Hardware Installation and SetupSafety Overview Power Requirements Installing into an Equipment RackRecommended Installation Tools Environmental Requirements SFP Mini Gbic Ports Installing the Optional External Power SupplyEquipment Rack Guidelines Connecting to the Network Connecting Power1 10/100/1000BaseT Ports Cabling Procedures Gigabit Ethernet Ports Cabling Procedures Pin Number Pair Number & Wire Colors Asante IntraCore IC36240 Initial Software Setup Connecting to a Console Connecting to a PC User Access Verification Password Privileges Commands Passwords and Privileges CommandsEnable Password Password Service Password-Encryption Username Command Login SecurityConfiguring an IP Address Password and login Commands Setting a Default IP Gateway Address Restoring Factory DefaultsSystem Boot Parameters Switchconfig# ip default-gateway Access Each Command Mode Understanding the Command Line Interface CLIUser Top User Exec Mode Document Conventions Privileged Top Privileged Exec Mode Command Show ? Purpose Global Configuration Mode Command Exit End Ctrl-Z Purpose Switch# configure Interface Configuration Mode Spanning-Tree Configuration Mode Vlan Configuration Mode Advanced Features Supported within the Command ModeSpanning-tree mst configuration Command Help Purpose Example of Context Sensitive Help Checking Command Syntax Switch# configure ? Using Command-Line Editing Features and Shortcuts Using CLI Command HistoryUsing the No and Default Forms of Commands Keystrokes/Command Purpose Completing a Partial Command Name Moving Around on the Command LineKeystrokes Purpose Editing Command Lines That Wrap Deleting Entries Redisplaying the Current Command LineScrolling Down a Line or a Screen Controlling Capitalization Transposing Mistyped CharactersKeystrokes Switch# clock ? Managing the System and Configuration FilesSetting the System Clock Switch# clock set 092930 28 January Switch# reload cr Specifying the Hostname Changing the PasswordTesting Connections with Ping Tests Enabling the System Log Configuring from the Terminal Managing Configuration FilesDisplaying the Operating Configuration Switch# show running-config Copying Configuration Files to a Network Server Newname# copy running-config startup-config Switch# copy startup-config ? Switch# copy running-config Tftp Switch# copy running-configSwitch# copy running-config tftp//192.168.0.1/my-config Access Control Configuring SnmpAuthentication Switch# copy tftp//192.168.123.59/my-confg running-config Security Levels Create or Modify Access Control for Snmp CommunitySupport Command Purpose Snmp-server community string view Establish the Contact and Location of the Snmp Agent Configuring Spanning Tree Snmp Configuration Commands Spanning Tree Parameters Spanning-tree mst? Port Priority Spanning Tree Port ConfigurationRapid Spanning Tree Protocol Rstp Port Path Cost Rapid Convergence Configuring Switch/Bridge PrioritySwitchconfig# spanning-tree priority priority Enabling Rapid Spanning Tree Configuring Port Path Cost Configuring Link TypeConfiguring an Edge Port Configuring Port Priority Multiple Spanning-Tree MST Configuring Vlan Vlan MAC Address Table Switchconfig# mac-address-table aging-timeShow mac-address-table Assign IP Addresses to Switch Configuring IPClass Address or Range Status Establish Address Resolution Define a Static ARP Cache Igmp Overview Configuring IgmpManaging IP Multicast Traffic Forwarding Unknown Multicast Packets Command Purpose Ip igmp query-max-response-time Using Access ListsSwitchconfig-if-veth1#ip igmp query-interval Host-query messages Using a Classification ACL Asante IntraCore IC36240 Create a Standard Access List Create an Expanded Access List Create a MAC Access ListSwitchconfig# mac access-list standard Access-list 101 deny tcp ? Access-list 101 ?Access-list 101 deny ? Access-list 101 deny tcp 192.168.123.0 0.0.0.255 ? Access-list ? Creating an Access List with a NameApplying an Access List to an Interface Access-list standard ? Configuring Common Access Lists Switchconfig# access-list 110 permit udp any any eq Access-list 101 deny ip any any Vlan Configuration Creating or Modifying a Vlan Switchconfig-vlan#port-member delete eth Switch# show vlanDeleting a Vlan Vlan Port Membership Modes Static AccessTrunk Ieee 802.1q Command Purpose Switchconfig# vlan dot1q tag native Switchconfig# end Monitoring Weighted Fair Queuing Lists Quality of Service ConfigurationConfiguring Weighted Fair Queuing Priority Queuing Defining the Priority List Configuring Traffic Shaping for an InterfaceTraffic Shaping Monitoring Priority Queuing Lists Monitoring the Traffic Shaping Configuration Configuring Rate LimitConfiguring Traffic Shaping for an Access List Generic Traffic Shaping Example Asante IntraCore IC36240 Configuring the Switch Using the GUI Main Configuration Menu Information Screens Front Panel Information Screen Assign IP Addresses to Switch General Information Screen Class Address or Range Status Port Configuration Menu Individual Port Configuration Screen Asante IntraCore IC36240 Press go Spanning Tree Protocol Configuration STP Port Configuration Global STP Bridge Configuration Snmp Configuration Asante IntraCore IC36240 Address Table Screen Asante IntraCore IC36240 Asante IntraCore IC36240 Vlan Configuration Asante IntraCore IC36240 Click Apply Igmp Configuration Asante IntraCore IC36240 Asante IntraCore IC36240 Web CLI Screen System Clock Menu Save Appendix a Basic Troubleshooting Problem Possible Solutions Environmental Range Appendix B SpecificationsPhysical Characteristics Performance Technical Support and Warranty Standards Compliance Appendix C FCC Compliance and Warranty Statements FCC Compliance Statement Important Safety Instructions IntraCare Warranty Statement Appendix D Online Warranty Registration Access List Index Igmp LED Safety Priority Queuing Vlan