Atto iPBridge 1550E | ATTO Technology 1550D/E, 1500D/E instruction

1.3 ATTO iPBridge 1550E

The iPBridge 1550E includes a single Ethernet port which may be used for either data transfer or configuration, a serial management port and a SCSI port.

Dimensions Length: 6.4 inches Width: 4.4 inches

Height of the tallest component: .536 inches

Environment

Operating Temperature: 5-40° C external Ambient air should not exceed 40°C. Humidity: 10-90% non-condensing Recommended airflow: 11 cubic feet per minute

Power

The iP1500E board may be powered from a 4-pin connector.

Input voltage: 12V DC ±10% derived from a 4- pin connection.

Power draw: 12V, 1.7 amps

4- pin power connector pin outs

Pin Description

112 volt input

2Ground

3Ground

4No connect

Reset switch

A manual reset switch is mounted on the board near the serial port.

SCSI port

The SCSI port on the iPBridge 1550E connects storage devices into the Storage Area Network (SAN). The port is an Ultra 3 LVD/SE SCSI bus with 68-pin “P” interface: 160 MB/sec. maximum throughput, downward compatible with all forms of single-ended SCSI.

The iPBridge supports SCSI devices including hard disk drives, tape drives RAID controllers, DVD, MO and CD libraries.

Ethernet port

The 10/100/1000 GbE RJ45 Ethernet port uses the Intel 8254x family gigabit Ethernet to support Telnet-based data transfer and management through a an ASCII-based command line interface or ATTO ExpressNAV, a browser-based interface.

GbE cables must be at least CAT-5E certified for 1000 Mb/sec. use.

Serial port

The RS-232 serial port provides support for remote monitoring and management through a command line interface. It is set at the factory at 115,200 bps.

Pin outs of the RJ11 connector, part number CBL-0911-001

Pin Description

2TXD

3Ground

4RXD

5Ground

LED indicators

Activity: A green LED in the middle of the iPBridge blinks to show the unit is ready and to identify the iPBridge when the CLI command IdentifyBridge is enabled. It goes dark when there is SCSI activity.

SCSI Activity: the SCSI bus has an LED which is lit when the iPBridge is ready and goes dark when there is SCSI activity.

7

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 16

ATTO Technology 1550D/E, 1500D/E Atto iPBridge 1550E, Pin outs of the RJ11 connector, part number CBL-0911-001

Contents

IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Intelligent Bridging Architecture, the engine GlossaryTerm Definition Introduction IPBridge1500 features Setting up the iPBridgeIPBridge 1550 features Possible SAN/NAS Configuration Scsi Pin outs of the RJ11 connector, part number CBL-0911-001 Atto iPBridge 1500E Installation instructions Exhibit 1.1-1 iPBridge 1500E board layout Atto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To connect Scsi devices to the Atto iPBridge Connecting Scsi devices to the Scsi portTo set Scsi port bus speed and transfer rates Cable types CablingExamples Connecting using the GbE port Configuring the iPBridgeTo find the iPBridge Using Atto ExpressNAV Connecting using the serial portTo optimize ExpressNAV in Internet Explorer Select Internet Options To connect using Telnet Using TelnetEnter Installation Configuration Change default username, password Scsi configurationTo change the default administrator password Managing the iPBridge Ethernet port configuration ISCSI configurationOEM configuration services Mapping Serial Port Configuration ExpressNAV provides web-based interfaceStatus To open an ExpressNAV session Bridge Configuration Advanced CLI ConfigurationTo use the Advanced Configuration Restart Firmware Command conventions Get Set Command Parameter 1 ParameterCLI provides ASCII-based interface Configuration & Management CLI CLI commands summary Command Defaults Example OEM configuration file Defaults Limits General use commands From information commands. Choices are enabled or disabled VerboseMode Diagnostic commands CLI Error Messages RouteDisplaySCSIPortList SCSITargets Maintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortBaudRate Serial port configuration commandsSerialPortEcho Configuration CLI Ethernet commands ReadOnlyPassword ReadOnlyUsername ISCSI commands ISNSServer MultiTargetMode AutoMap Mapping commandsRoute Configuration CLI Privileged OEM configuration services OEM Config file supported commands ModelNumberProductID VendorID Single target mode Use Command Line InterfaceMapping devices Node names Mapping single vs. multiple target mode Multiple target mode Use the ExpressNAV interface Example To remove an iSCSITarget To use FTP over GbE to flash new firmware into the iPBridge Updating firmware\bridgefirmware\I1500110.ima Configuration & Management firmware update Appendix a Safety standards and compliances European Standards FC Rack Enclosures with Power Supplies PWRA-0000-FRUPower Module for Atto FC Rack SystemAtto iPBridge 2500C Atto iPBridge 1500E Accessories Cables/SCSI Appendix C Contact Atto Technology, Inc