Connecting Scsi devices to the Scsi port | ATTO Technology 1500D/E

1.5	Connecting SCSI devices to the SCSI port	11
	Cabling
	Cable types
	Examples
1.6	Configuring the iPBridge	13
	Connect using the GbE port
	Using ATTO ExpressNAV
	Connecting using the serial port
	Use Telnet

2 Managing the iPBridge

17

Change default username, password SCSI configuration

Ethernet port configuration iSCSI configuration Mapping

OEM configuration services

2.1 ExpressNAV provides web-based interface

19

Status

Serial Port Configuration

Ethernet Port Configuration

SCSI Configuration

iSCSI Configuration

Bridge Configuration

Mapping

Advanced CLI Configuration

Restart Firmware

Help

2.2 CLI provides ASCII-based interface	21
2.2.1 CLI commands summary	23
2.2.2 General use commands	25

Help

Password

ReadOnlyPassword

ReadOnlyUsername

RestoreConfiguration

SaveConfiguration

Username

VerboseMode

2.2.3 Diagnostic commands

27

BridgeModel

BridgeName

Help

IdentifyBridge

Info

IsReserved

Image 5

ATTO Technology 1500D/E, 1550D/E operation manual Connecting Scsi devices to the Scsi port

Contents

IPBridgeTM 1500D/E IPBridgeTM 1550D/E Page Page Contents Connecting Scsi devices to the Scsi port Serial port configuration commands Mapping commands Term Definition GlossaryIntelligent Bridging Architecture, the engine Introduction IPBridge 1550 features Setting up the iPBridgeIPBridge1500 features Scsi Possible SAN/NAS Configuration Atto iPBridge 1500E Pin outs of the RJ11 connector, part number CBL-0911-001 Exhibit 1.1-1 iPBridge 1500E board layout Installation instructions Atto iPBridge 1500D Exhibit 1.2-1 iPBridge 1500D back panel Atto iPBridge 1550E Exhibit 1.3-1 iPBridge 1550E board layout Atto iPBridge 1550D Exhibit 1.4-1 iPBridge 1550D back panel To set Scsi port bus speed and transfer rates Connecting Scsi devices to the Scsi portTo connect Scsi devices to the Atto iPBridge Examples CablingCable types To find the iPBridge Configuring the iPBridgeConnecting using the GbE port Connecting using the serial port Using Atto ExpressNAVTo optimize ExpressNAV in Internet Explorer Select Internet Options Enter Using TelnetTo connect using Telnet Installation Configuration Scsi configuration Change default username, passwordTo change the default administrator password Managing the iPBridge ISCSI configuration Ethernet port configurationOEM configuration services Mapping ExpressNAV provides web-based interface Serial Port ConfigurationStatus To open an ExpressNAV session Advanced CLI Configuration Bridge ConfigurationTo use the Advanced Configuration Restart Firmware CLI provides ASCII-based interface Get Set Command Parameter 1 ParameterCommand conventions Configuration & Management CLI Command Defaults Example CLI commands summary OEM configuration file Defaults Limits General use commands VerboseMode From information commands. Choices are enabled or disabled Diagnostic commands RouteDisplay CLI Error MessagesSCSIPortList SCSITargets Maintenance commands Configuration CLI Scsi configuration commands SpeedWrite SerialPortEcho Serial port configuration commandsSerialPortBaudRate Configuration CLI Ethernet commands ReadOnlyUsername ReadOnlyPassword ISCSI commands MultiTargetMode ISNSServer Route Mapping commandsAutoMap Configuration CLI Privileged OEM configuration services ModelNumber OEM Config file supported commandsProductID VendorID Use Command Line Interface Single target modeMapping devices Node names Mapping single vs. multiple target mode Use the ExpressNAV interface Multiple target mode To remove an iSCSITarget Example \bridgefirmware\I1500110.ima Updating firmwareTo use FTP over GbE to flash new firmware into the iPBridge Configuration & Management firmware update Appendix a Safety standards and compliances European Standards PWRA-0000-FRUPower Module for Atto FC Rack System FC Rack Enclosures with Power SuppliesAtto iPBridge 2500C Atto iPBridge 1500E Cables/SCSI Accessories Appendix C Contact Atto Technology, Inc