Projector warm up, G2 Adjustment CRT RUN in Cycle | Barco R9000740

SERVICE MODE

Projector warm up

SERVICE MODE

Highlight 'Projector warm up' by push- ing the control disk up or down and press ENTER to select the projector warm up menu.

The ON/OFF option can be toggled with the ENTER key.

When in the ON position (and the CRT run in cycle is OFF), the projec- tor can start up with a warm up periode of 20 minutes. During the start up a warm up menu will be displayed. This menu offers the possibility to skip the warm up periode anyway by pressing the EXIT key and offers the possibility to adjust the horizontal and vertical amplitude of this white image with the control disk. During this warm up period, a full white image is shifted on the CRT faceplate to avoid a burn in.

Every 30 seconds a text box will be displayed on another place on the screen with the remaining time to go. When EXIT is pressed during this warm up periode, the warm up menu will be redisplayed with the remain- ing time indication. Press another time EXIT to interrupt the warm up cycle.

When the warm up option is OFF, when switching on the projector, it starts immediately with the projec- tion of the selected source

COMMON SETTINGS

G2 ADJUSTMENT

CRT RUN IN CYCLE

PROJECTOR WARM UP

Select with or

then <ENTER>

<EXIT> to return.

PROJECTOR WARM UP

OPTION : ON

A FULL WHITE PATTERN WILL BE GENERATED FOR 20 MINUTES AT POWER UP AFTER THIS PROCEDURE THE PROJECTOR IS READY TO PERFORM IN OPTIMUM CONDITION

TOGGLE OPTION ON OR OFF

with <ENTER> <EXIT> to return

9-20		R5975228 BARCOVISION 701 MULTIMEDIA 070597
9-20		R5975228 BARCOVISION 701 MULTIMEDIA 070597

Image 122

Barco R9000740 owner manual Projector warm up, G2 Adjustment CRT RUN in Cycle, Toggle Option on or OFF

Contents

R9000740 Page Table of Contents Guided Adjustment Mode MESSAGES, Warnings and Failures Orbiting Kit Safety Instructions Safety Instructions Part Number SER. Number Dealer Installation InstructionsOWNER’S Record Safety Instructions On safety Mains lead Power cord with CEE 7 plug Power cord with Ansi 73.11 plug On servicing On repacking Safety Instructions Location and Function of Controls Location and Function of Controls Rear Panel Terminology RS232OUT Front Panel Terminology RCU control panel terminology Getting accessControl panel terminology a. The local keypad Location ControlsFunction ADJ. adjust key, to enter or exit the adjustment mode Power Mains Connection Power Connection Power mains cord connection Switching on/off Connections Source ConnectionsPeripheral Equipment Connection Signal input connection to the projector Source No Projector input Press digit button Connecting a Composite Video source Video input selection EN ER AL a CC ES S Connecting a RGB Analog source with composite sync GE NER AL a CCE SS Rgbs or RGsB input selection Connecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selection Connecting a Component source YYB-YS orR-YYsB-Y input selection Connecting a Component source with Tri-level sync N E R a L a C C E S S YYB-Y3S or R-YY3sB-Y input selection Remote control Data communications Connecting an IR Remote Receiver to the projector Connecting a Rcvds 05 switcher to the projectorConnecting a VS05 switcher to the projector Peripheral Equipment Controlling Battery installation in the RCU Controlling RCU used in a hardwired configuration How to control the projector How to display a projector address?Hardware set up of the projector address Using the RCU How to program an address into the RCU? Input selection Source No Projector input Press digit button Our c e = 15 k Hz = 50 Hz R N I N G Brightness Control I G H T N E S S N T R a S T L O R Contrast ControlColor Saturation Control A RP N E S S Tint ControlSharpness Control Controlling Start UP of the Adjustment Mode Start UP of the Adjustment Mode Random Access Service Adjustment Guided Entering the adjustment modeInstallation Only for qualified Technician Adjustment mode Access menu DJ U S TM E NT M OD E Adjustment ModeStart UP O N G S S W O R D M P O S E S S W O R D Guided Adjustment Mode Guided Adjustment Mode Start up of the guided adjustment mode Overview flowchart Guided Adjustment procedure I D E D a D J U S T M E N T M O D E Selecting Setup Pattern Internal # Pattern Internal Cross Hatch PatternGuided GU IDE D a DJU STM ENT MO DE Line Doubler option Picture tuningSync Fast/Slow toggle PIC Ture TUN ING Enhanced blue ON/OFF C T U R E T U N I N G Raster Centering on Green CRT Faceplate V Shift Correct raster position Wrong raster position EFT-RIGHT E/W Left-Right East-West AdjustmentsShifting Red and Blue on Green Vertical Centerline Bow Adjustment Vertical Centerline Skew Adjustment Right Bow Adjustment Right Keystone AdjustmentLeft Keystone Adjustment Left Bow Adjustment Horizontal Size Adjustment Top-Bottom North-South Adjustments To P -BO TTO M Top Keystone Adjustment Horizontal Centerline Skew AdjustmentHorizontal Centerline Bow Adjustment Bottom Bow Adjustment Top Bow AdjustmentBottom Keystone Adjustment Z E-L I N E AR I T Y Size-linearity AdjustmentVertical Linearity Adjustment Vertical Size Adjustment Horizontal Phase Adjustment Convergence Adjustment N V E R G E N C E Blanking Adjustment A N K I N G Top blanking adjustment Bottom blanking adjustment Right blanking adjustment Guided Adjustment Mode Custom Black Balance Color BalanceCustom White Balance Random Access Adjustment Mode Random Access Adjustment Mode Starting up the random access adjustment mode DJ U S TM E NT M OD E Overview flowchart Random Access Adjustment mode N D O M a C C E S S J U S T ME N T MO D E A N K I N G T E R N a L # P a TT E R N Random access adjustment mode selection menu AN D OM AC C ES S DJ US TM E NT M OD E Random Access Adjustment Mode Sync Fast/Slow Adjustment Custom Color Balance Ture Enhanced Blue On/Off AdjustmentLine Doubler TUN DJ US TM E NT M OD E CO L or SEL E CTAN D OM AC C ES S O M E T R Y Horizontal Phase Adjustment Enter Correct by pushing Control disk to the right Raster Shift Adjustment A R S E S H I F T Press Exit to return to the Geometry menu F T -R I G H T Access Adjustment Mode F T -R I G H T TOP BOT TOM All adjustment are indicatedBetween 0 and 100. See next Example H Certerline Bow Control disk down Control disk up Horizontal Size Adjustment Vertical Linearity Adjustment Vertical Size Adjustment Left blanking Right blanking Correct by pushing the control disk up or down E E N O N L Y Re e n ima g e Service Mode Service Mode Starting up the Service mode J U S T M E N T M O D E Overview flowchart Service mode Identification Memory Management Common Settings I2C DiagnosticsProjector Set-up Identification Total RUN Time Service Total Run Time Change password Change Projector Address Change Baudrate English Españ OL Francais Deutsch Identification Total RUN Time Change PasswordChangeLanguage A N G E P a S S W O R D Change Projector Address Changebaudrate Power up mode Identification Mode on Size Small Background on Orbitting on BARCOlogo Projector SET-UP Common Settings I2C DiagnosticsCopy a block Copy a Block Delete a Block Delete ALL Blocks P Y B L O C K Deletion of blocksP Y M O D E EL E T E B L OC K Deleting block by blockLE T E M O D E Copy a Block Delete a Block All settings to midpositionDeletion of all blocks EL ET E a L L BL O C K S Convergence MID GR Convergence MID Undo all settings to midposConvergence mid ALL Settin GS to M ID Posi Tion Green convergence mid ALL Settings to Midpos R & B Convergence MIDUndo R & B convergence mid C O N VER G EN C E M ID Projector SET-UP Memory Management G2 Adjustment CRT RUN in Cycle Projector Warm UPUndo green convergence mid F E T Y T I C E SK O F E LE C T R I C AL S H O C K G2 AdjustmentCRT RUN in Cycle Projector Warm UP T R U N in C YC LE CRT run in cycle Option on G2 Adjustment CRT RUN in CycleProjector warm up Toggle Option on or OFF Projector SET-UP Memory Management Common Settings Decoder Service Mode MESSAGES, Warnings and Failures MESSAGES, Warnings and Failures Projector Address MESSAGES, Warnings and Failures InputSource Input se- lector not available Invalid Key entryInput no Longer Available Iris FailureWait Options IR receiver Hardwired RCU Projector Control softwareOptions IR Receiver Shield Conductor VS05 D9-D9 communication cable Contrast modulation kit Orbiting KitSoft edge matching kit Battery replacement in the RCU Appendix a Battery Replacement in the RCU Appendix a Battery Replacement in the RCU Appendix B Orbiting Orbiting mode toggle switchesOrbiting option Orbiting Master/slave toggleOrbiting ON/OFF toggle only in Master Orbiting S T E R O R B I T I N G Orbiting alignment Adjustment procedure stand alone projectorOrbiting speed toggle only in Master Orbiting Appendix B R I Z O N T a L BI T AM P L Adjustment procedure multiple projector installations J US T D E V I ATI O N Appendix B Orbiting Soft edge matching option Appendix C Soft Edge Matching Basic concept S S Highlight H Test Mode and press Soft Edge Matching Start positionAppendix C Appendix C Soft Edge Left image areaMatching Stop position Right image area Vertical test mode Top soft edge area adjustment F T E D G E R R E C T I O N Bottom soft edge area adjustment Edge Matching Contrast modulation option Appendix D Contrast Modulation Modulation Enter selects the Contrast Modulation menu Appendix D Contrast equalisation Color ShiftContrast Modulation Contrast edge correction hot spot R TI C a L N T R a S T G E C or R E C T I O N Appendix D Contrast Modulation Appendix E Adjustment Blocks Adjustment Blocks memory blocks32 adjustment blocks are in use. What to do? Projector equipped with Rcvds or VS05 T E N T I O N Appendix F Source numbers 90Source Numbers 90 Appendix F Source Numbers 90 V D S