Step L | BENDIX BW2849 specification

Fault Isolation Procedures

Power-Up Sequence Test, continued

Step L	Procedure	Condition	Action

1.Key off.

2.Connect spare Driver Display to 4-way connector.

3.Key on.

4. Check error codes.		If no error codes		Replace Driver Display Unit.
				Go to Step V.
				Go to Step V.
		If error codes		Go to Step A.
				Find error in testing.
				Find error in testing.

Power-Up Sequence Test

2-16

Image 27

BENDIX BW2849 manual Step L, If error codes Go to Step a Find error in testing

Contents

Troubleshooting Guide Related Publications Fault Isolation ProceduresGeneral Warnings Suggested Tools Component and System Codes Symptom TestsIntroduction Pretests YES Diagnostic Procedure Service Procedure Fault Code Retrieval and Clearing Fault Hand-Held Codes Fault Code Isolation Procedure Index Driving Techniques Speed Input Signal System Right Turn Signal System Key on. If the fault is present,Heat and vibration Brake Input Signal System On. Apply Service Brake For Minimum Seconds. If Description Type of Code Driving Technique 250 Seconds to set this fault Symptom-Driving Index Fault Isolation Procedures Service Procedure Overview Electrical Pretest Electrical Pretest Step a Key off Disconnect negative battery cable Step BMeasure resistance Step C Driver Power-Up Sequence TestCentral Processing Unit Driver Display Unit Vehicle Harness Central Freightliner IDI Measure voltage If voltage is between Power-Up Sequence TestKey on Observe the Driver If lights turn on the go off If lights turn on and stay on If any of the above conditions are not met Go to Step D Measure resistance between Step D Key off Measure resistance betweenIf any of the above conditions are not met Go to Step E If any of the above conditions are not met Go to Step F Step E If any of the above conditions are not met Go to Step G Step F Step G Antenna 4-way connector Step H Go to Step J StepMeasure resistance between Central Processing Are not met Step J Go to Step L Key on Check error codes If no error codesIf error codes Step K Step L If error codes Go to Step a Find error in testing Clearing on If code appears Key off Reconnect all connectors Key onCompatibility problem Contact your Bendix Representative Check for Codes. See If no codes Test complete This page left blank intentionally Component Code 11 SID 254, FMI 4 Central Processing Unit CPU Basic Hand Tools Troubleshooting Guide Code 11, 12 SID 254, FMI 4, 12, Central Processing Unit CPU Key off Retrieve codes If code 11 is activeIf code 11 is inactive Test complete Component Code 13 SID 9, FMI 2, 4, 5 Driver Display Unit This fault causes a failure of the Bendix Vorad system Driver Display Unit 4-way Code 13, 34 SID 9, FMI 2, 4, 5, 12 Driver Display UnitAvailable, go to Step B Go to Step If voltage is 7.0 to 7.5 volts Step C Key off Measure resistance between Central Processing 5,12 Step E Repair OEM wiring harness Unit. Go to Step If code other than 13 or TestingAppears Procedure Index on Clearing on page 1 If code 13 or 34 appears Component Code 14 SID 1, 2, FMI 2, 12 Antenna Assembly Key off Unplug the Antenna 4-way connector Key on Code 14, 35 SID 1, 2, FMI 2, 12, 14 AntennaPin 3 and pin If voltage is outside of range Step C Step D Step E Step F Go to Step Clearing on page 1 If code 14 appears See Fault Code Isolation Component Code SID 10, FMI Right Side Sensor Right Side Sensor? Key on Measure voltage between Pins a and B Pins a and CIf voltage between pins a Code 15 SID 10, FMI 2 Right Side Sensor If resistance is outside of range Go to Step D If resistance is outside of range Go to Step E Measure resistance between Way pin C13 and 3-way pin B Replace Central processing Unit. Go to Step See Fault Code Isolation Procedure Index on page 1 Component Code SID 11, FMI Left Side Sensor Left Side Sensor? Code 16 SID 11, FMI 2 Left Side Sensor If resistance is out of range Go to Step D If resistance is out of range Go to Step E Measure resistance between Way pin D13 and 3-way pin B If resistance is out of range Index on page 1 Clearing on page 1 If code 16 appears Right Central Processing Unit Turn Signal Component Code SID 7, FMI Right Turn Signal Required. Go to Step Code 21 SID 7, FMI 2 Right Turn SignalRepair OEM wiring harness as If equipped with a Right Side Sensor Key off Turn on right turn signal Volts of battery voltageIf voltage ﬂashes within If code other than 21 appears Left Component Code SID 8, FMI Left Turn Signal Code 22 SID 8, FMI 2 Left Turn Signal If voltage measures within Key off Turn on left turn signal If code other than 22 appears This fault causes a failure of the Vorad system Component Code SID 3, FMI Brake Input Error Proper conﬁguration Code 23 SID 3, FMI 2 Brake Input ErrorGo to Step B If the brake lights are not Working correctly Go to Step Connector If there is not a wire in C9 Check pin C9 on 32-way If there is a wire in C9 Key off Depress brake pedal Clearing on page 1 If code 23 appears Check for Codes. See If no codes appear Test complete This page left blank intentionally Component Code SID 6, FMI Speed Input Error Code 24 SID 6, FMI 2 Speed Input Error Unit 32-way connector Have pins in C10 and C11If vehicle uses J-1939 or 1587 conﬁguration Between speed sensor Pins a and B 10K ohms or open circuitOhms Clearing on page 1 If code 24 appears Component Code 25 SID 231, FMI 2, 12 Cruise Signal Error TerminatingResistor If resistance is outside of range Go to Step B Way pin D7 and ground See Engine OEM for PIN Location See Engine OEM For PIN Location Key off Measure resistance Key on If error codes Problem exists with Engine ECU. Repair Key off Reconnect engine ECU connector If code other than 25 appears This page left blank intentionally Component Code SID 250, FMI Data Link Error Code 31 SID 250, FMI 2 J-1587 Data Link Error If resistance is outside of range Go to Step C If communication errors Key on If no communication errors If code other than 31 appears This page left blank intentionally Component Code SID 248, FMI Vbus Error If any of the above conditions are not met Go to Step B Code 33 SID 248, FMI 12 Vbus Error If any of the above conditions are not met Go to Step C Driver Display Connector pin D5 Step D Clearing on page 1 If code 33 appears On page 1 Antenna Not Detecting Targets Symptom Isolation Procedures Appropriate isolation Properly Go to Step a Procedure Side Sensor Not Detecting Targets Side Sensor Detection Test Between pins 2 Key on Measure voltageGo to Step D If voltage is outside of range Replace Side Sensor Display. Go to Step Go to Step E Measure resistance between Way pin C164-way pin Way pin C16 Ground Key off Measure resistance between Way pin C14 Way pin C14 GroundGo to Step Go to Step F If resistance is outside Key off Measure resistance between Way pin C12Way pin C12 Ground Ground is more than Step Detection Test There is no fallback mode for this symptom Driver Card Not ReadingNew Driver Card Driver Card Detection Test Appendix Bendix Vorad System Wiring Diagram Eatonvorad Wiring Diagram Nvram Fault Code Tree