Setting the T1/E1Parameters | Black Box LR1530A-R3, LR1530A-EU-R3

Installation

Setting the T1/E1Parameters

(T1/E1 WAN only)

The parameters requred for a T1 or E1 connection may be obtained from your service provider. These may then be entered via the T1/E1 set-up menu to configure the router for that service.

7T1/E1 Selection: Location: Main

ÄConfiguration

ÄWAN Set Up

ÄLink Set Up

ÄT1/E1 Set Up

ÄLink mode T1 or E1

Set the service mode to which this router will be connected.

7Service parameters: Location: Main

ÄConfiguration

ÄWAN Set Up

ÄLink Set Up

ÄT1/E1 Set Up

ÄSpeed/Channel rate 56/64 kbps

ÄT1/E1framing

framed/unframed/SF/ESF

ÄLine encoding AMI/INV_AMI/ B8ZS/HDB3

Select the service channel speed, framing format, and encoding as designated by the service provider.

T1 service requires the specification of a Line Build Out factor. This parameter modifies the transmitted signal to compensate for degradation due to line losses between the transmitter and receiver. A number of different options are available to meet standards for T1 long haul (direct connection to service providers central office facility), T1 short haul (connection through a local PBX), AT&T TR64211 specification long haul and AT&T TR64211 short haul. Your service provider will tell you which specification their service requires. Short

12

Image 18

Black Box LR1530A-R3 manual Setting the T1/E1Parameters, T1/E1 Selection Location Main, Service parameters Location Main

Contents

Frame Relay/Leased Line Bridge/Router Specifications Normas Oficiales Mexicanas Electrical Safety Statement Page Page Page Contents Introduction to Filtering Appendix D Software Upgrades Page Unpack the unit Select a Site Identify the Connectors Rear View of the CSU-DSU router Connect to the Console Make the LAN ConnectionsMake the WAN Link Connection Installation Power Up the router Login and Enter the Required Configuration Mandatory Configuration Mandatory Configuration Setting the Link Interface Type Set Link Interface Type Location MainLink Interface Type T1/E1 Selection Location Main Setting the T1/E1ParametersService parameters Location Main Framed/unframed/SF/ESF As specifed First channel Number number of channels Set Link Interface Type Location Main Identify the Status LEDs Green Front View of the router Typical Applications & HOW to Configure Them Managing the router Using Menus Configuration Option Name Location Main ConventionsOption Name Basic Frame Relay Configuration Frame Relay configuration Frame Relay enable Location Main Link Speed Location MainLink Speed Auto Learning the Frame Relay Configuration Manual Configuration LMI Type Auto-Learning Location MainLMI Type Quick Start Frame Relay IP AddressIP Address / Subnet mask size PPP Encapsulation Location Main Disabled Basic Leased Line ConfigurationFrame Relay disable Location Main Quick Start PPP Leased Line Connections Basic PPP Leased Line Configuration Local IP Address Location Main Bridge Connection Should You Bridge or Route? Configure as an Ethernet Bridge Bridged Local Area Networks IP Address Applications Configure as an Ethernet IP router IP Routed Local Area Networks IP Address Define an IP Default Gateway Default Gateway Location MainDefault Gateway Define an IP Static Route Edit Static Route Location MainRemote Site Next Hop Cost Add Define an IP Subnet Mask IP Address & Subnet Size Location Main IP Address / mask size Applications Configure as an Ethernet IPX router Novell Servers in Both Locations Applications Novell Servers in One Location Only IPX Routed Local Area Networks Servers on one side IPX Frame Types Location Main PPP Link Configuration Overview Numbered Links Unnumbered Links Server Configure Dynamic Host Configuration ProtocolDhcp Services Location Main IP Address Pool Location Main Local + External DNS Server Configuration DNS Set-Up Location Main Enabled Configure Network Address Translation NATNAT Enabled Location Main NAT Exports Translation type Location Main Configure PPP Security Security Level Location MainSecurity Level Incoming PAP Password Incoming Chap Secret Outgoing PAP Password Outgoing Chap SecretSecurity Database Entry Location Main Configure Firewall 10 Sample Firewall Application Firewall WAN Remote Site Filter direction Location Main FTP & WWW Designated Servers Location Main Firewall LAN Filter Direction Location Main Firewall Table Entry Location Main Firewall Location Main Applications MAC Address Filtering Introduction to Filtering Pattern Filtering Not Introduction to Filtering Bridge NetBIOS &NetBEUI Microsoft WindowsPopular Filters IP & Related Traffic IP Router NetBIOS over TCPBanyan Other interesting TCP Ports Appendix a Menu Trees Menu Tree From previous Page Appendix B Octet Locations on Ethernet Frames Octet Locations on Ethernet Frames Ethernet Type Codes ARP Octet Locations on Ethernet Frames Octet Locations on a Bridged XNS Frame Octet Locations on Ethernet Frames Opening the case Appendix C Servicing Information Identifying the Internal Components CPU J11 Sanity Timer To Clear a Lost PasswordForce Zmodem Software Load Connecting to the Console Connector Figure C-3 Rear View of the Console and LAN Connectors Module WAN Interface ConnectionPinout Information CSU/DSU Module T1/E1 Module T1/E1 Universal WAN Module Connecting cable must be a shielded cable Link Pinouts Servicing Information RS232C / V.24 Link Pinouts DCE RS530 / RS422 Link Pinouts Figure C-8 RS530 / RS422 Link Pinouts 11 / X.21 Link Pinouts Figure C-9 V.11 / X.21 Link Pinouts 11 / X.21 DB25 to DB15 Connector Cable Figure C-10 V.11 / X.21 DB25 to DB15 Connector Cable Null-Modem Cable Configuration Figure C 11 V.35 Null-Modem Cable RS232 / V.24 Null-Modem Cable Figure C-12 RS232 / V.24 Null-Modem Cable Signal Ground DTE Ready a RS530 / RS422 Null-Modem Cable Servicing Information Appendix D Software Upgrades Considerations Servicing Information Page PC used for Tftp transfers Link