Turning Off the Power | Boss Audio Systems GT-6B manual

Chapter 1 Playing Sounds

Turning Each of the Effects in a Patch On and Off

You can use pedals 1–4 to switch on and off the individual effects that are used in a patch. Each pedal shows the names of two effects; the effect that you are currently able to switch on and off is indicated in the lower row of the right display. You can also change these with [PEDAL ASSIGN] (p. 45).

Switching Patches by Specifying the Bank and Number

The GT-6B has been set at the factory so that you can switch patches using the PATCH/VALUE dial or the

PATCH and PATCH pedals, but you can change the settings by switching patches directly with the bank and number. For more detailed information, refer to p. 60.

About the Information Appearing in the Display

The following information is shown in the display.

Number Patch Name

Bank

Effects

If the Patch Does Not Switch

On the GT-6B, you cannot switch patches in any screen other than the Play screen. If you are having this problem, press [EXIT] to return to the Play screen.

Turning Off the Power

1.Before turning off the power, confirm the following.

•Is the volume on the GT-6B, your amp, and all other connected devices turned down to the minimum level?

2.Turn off the power to the bass amp (power amp) and other devices.

3.Turn the GT-6B’s power off.

Chapter 1

15

Image 15

Boss Audio Systems GT-6B owner manual Turning Off the Power, Turning Each of the Effects in a Patch On and Off

Contents

Copyright 2002 Boss Corporation Printing Conventions in This ManualPage Page Memory Backup Power SupplyPlacement Maintenance Contents Contents Main Features Panel Descriptions Front PanelCOMP/LIMITER p Compressor/Limiter Chorus p REV/DLY p Reverb/DelayPanel Descriptions OVERDRIVE/DISTORTION p Panel Descriptions WAH p FX-1 pFX-2 p Rear Panel Making Connections Playing Sounds Next, turn on the power to the bass amp power amp Turning On the PowerAdjusting the Output Level Switch on the Power switch on the GT-6B’s rear panel What is a Patch? How to Switch PatchesSelecting Patches Turning Each of the Effects in a Patch On and Off Turning Off the PowerIf the Patch Does Not Switch Switching Patches by Specifying the Bank and Number Limiter THR Limiter threshold Adjusting the Tones with the KnobsGetting the Tones You Want- Fast EZ Tone Comp ATK Compressor attack Creating You Own Favorite Tones Patches Repeat Steps 1 To select another effect to be switched on and offSwitch on and off Adding and Omitting Effects Rotate the Value dial to change the settings value Parameter whose settings are to be changedQuick Setting Rotate the Value dial to select the effect setting you Using the Pedal Effects Wah, Pedal Bend, Ring Modulator Pedal BendPress FX-2 Turn on the FX-2 effect Adding Effects p Press NAME/NS/MASTER until Name appears in the display Naming TonesRing Modulator Press FX-1 Turn on the FX-1 effect Adding Effects p Appears in the display Changing the Order of the Effects Effect Chain Saving the Tones You Have Created WriteCopying Patches Saving the Tones You Have Created Exchanging Patches Compressor/Limiter Effects Explained FUZ Fuzz OD/DIST Overdrive/DistortionOD Overdrive DST Distortion REV/DLY Reverb/Delay/ SOS Sound On Sound REV Reverb DLY Delay Reverb & Delay SOS Sound On SoundPreamp Speaker FX Select Effect Select WH Pedal WahEffects Explained Direct Level Freq Frequency AW Auto Wah TW Touch Wah Effects Explained Rate FX-1OCT Octave ENH Enhancer Mix Level SG Slow GearDEF Defretter Effects Explained Sens FX-2 PH Phaser HRM Harmonist FL Flanger Pitch Shifter 2CE 2x2 Chorus PB Pedal Bend ASL Auto Slap SDD Short Delay LengthSound Vowel VIB VibratoHMN Humanizer Trigger SYN Bass Synth Noise Level Octave ShiftPWM Rate Pulse Width Modulation Rate PWM Depth Pulse Width Modulation Depth NS Noise Suppressor FV Foot VolumeQuick Settings p Manual Settings p Setting the Range of the Volume Change Settings for Using Expression Pedal Pedal Settings for the CTL Pedal Making Settings Instantly Quick SettingsSetting the Pedal Functions Pedal Assign Pedal Settings for the Expression Pedal Switch Target Variation Range Editing Quick SettingsSource Mode Target Press Pedal Assign Making the Assign On/Off Setting Target Making the Parameter SettingsWhen using the foot switch When using the expression pedal Source Source Mode For Pitch Shifter Setting the Pedal Functions Pedal Assign Active RangeFor Foot Volume Example Act. Range Lo 40, Act. Range Hi Making Custom Overdrive/Distortion Settings Using the Customize Function Using the Customize Function Making Custom Pedal Wah Settings Using Sound On Sound ProcedureNumber 4 pedal Stop, Erase Switching the XLR Output Connector Signals Convenient Features of the GT-6BUsing the Expression Pedal Even When Bypass Is in Effect Switching Bypass On and Off Convenient Features of the GT-6B Quick Patch Volume Adjustment Effect Level KnobTuning the Bass About the Display During Tuning How to Tune Changing the Tuner SettingsStandard Pitch 435-445 Hz Revrb Level Reverb Level 0%-200% Using the Digital OutAdjusting the Output Level from Digital OUT NS Thrshold Noise Suppressor Threshold -20 dB-+20 dB Press Utility a number of times until Meter is displayed Checking the Effect Output Level with the Level Meter Other Functions Adjusting the Display Contrast LCD ContrastLimiting the Banks That Can Be Switched Bank Extent Switching Only the Number Immediate Other Functions Switching the Bank and NumberPress the Bank or Bank pedal to select the desired bank Press a number pedal to select the patch you want to use Patch No.& Value Setting Expression Pedal HoldSelecting the PATCH/VALUE Dial Function Dial Function Other Functions Setting the Knob Functions Knob Mode Controlling the GT-6B Remotely From an External Midi Device Using MidiWhat Can You Do with MIDI? Operating From the GT-6B Using Midi Making the Settings for Midi Functions Midi CTL OUT Midi Control Pedal Out Off, 1-31 Midi Expression Pedal Switch Out Off, 1-31Midi PC OUT Midi Program Change Out Off, On Midi EXP OUT Midi Expression Pedal Out Off, 1-31 Transmitting Transmitting and Receiving Midi DataTransmitting Data to an External Midi Device Bulk Dump Making the Connections Press Exit to quit Bulk Load When Receiving Data Saved on a Midi SequencerReceiving Data from an External Midi Device Bulk Load Receiving Initial Program Change Map Settings Setting the Program Change Map Using Midi Main types of Midi message used by the GT-6B AppendicesAbout Midi How Midi messages are transmitted and received About the Midi implementation Factory Settings System Restoring the Factory Settings Factory ResetAdjusting the Expression Pedal Appendices Can’t Change Patches TroubleshootingNo sound / Volume is weak Volume level does not change with Foot Volume Error Messages Appendices Midi messages are not transmittedReceived Midi Implementation Chart GT-6B Bass Effects Processor Main Specifications Numerics Index LPF Index THR Memo Memo Avis G601744601