Manuals / Brands / Computer Equipment / Printer / Brady / Computer Equipment / Printer

Brady 200M, 260M Peel-off, Print Speeds, Media Handling, Printer Specifications, Printing Considerations, ∙Tear-offmode: Produced in strips

1 104

Download 104 pages, 1.8 Mb

IntroductionM-Series User ’s Guide

Printer SpecificationsPrinting Considerations

	Specification		200M		260M
	Resolution (thermal transfer or direct		203 dots per inch	Optional 152 dots	203 dots per inch
	thermal)		(8 dots per mm)	per inch (6 dots	(8 dots per mm)
				per mm)

	Dot size		0.00492"	0.00656"	0.00492"
			(0.125 mm)	(0.167 mm)	(0.125 mm)
	Maximum print width		4.09" (104 mm)		6.30" (160 mm)
	Maximum	Standard memory	15" (381 mm)	26" (660 mm)	9.5" (241 mm)
	print length
	print length	With 512 KB additional	39" (991 mm)	39" (991 mm)	25" (635 mm)
		With 512 KB additional	39" (991 mm)	39" (991 mm)	25" (635 mm)
		memory
	Bar code modulus (“ X” ) dimension		5 mil to 55 mil	6.6 mil to 72 mil	5 mil to 55 mil

	Thin film printhead with Energy Control

Print SpeedsProgrammable constant printing speeds of 2″ (51 mm),3″ (76 mm), 4″ (104 mm), 5“ (127 mm), and 6″ (152 mm) per second.Media Handling∙Tear-off mode: Produced in strips.

∙Peel-off mode: Requires Peel-Off option or Media Rewind option. Labels are dispensed and peeled from the liner, and the liner is rewound internally.

∙Rewind mode: Requires Media Rewind Option. A full roll of printed labels are rewound internally.

1-6

Contents

Page BradyprinterTM THT Model 200M and 260M Thermal Transfer Printer USER'S GUIDE Proprietary Statement Product Improvements FCC Compliance Statement Canadian DOC Compliance Statement Liability Disclaimer Bradyprinter™ THT Models 200M and 260M WARRANTY INFORMATION 1. Printer Warranty 2. Supplies Warranty 3. Warranty Exclusions and Conditions Table of Contents Introduction Installation Operation Configuration and Calibration Interconnections Preventive Maintenance Troubleshooting Options Appendix A - 240 VAC Power Cord Appendix B - ASCII Code Chart Appendix C - Adjusting Bar Code Darkness Introduction Page Additional System Requirements Media and Ribbon Requirements run tests for your applications Warnings and Precautions CAUTION: CAUTION: Refer to the Interconnections Section Page Printer Specifications Printing Considerations Print Speeds Programmable constant printing speeds of 2″ (51 mm) 3″ (76 mm), 4″ (104 mm), 5“ (127 mm), and 6″ (152 mm) per second Media Ribbon Zebra Programming Language II (ZPL II®) Bar Codes Options Section Page Page Page Installation remove any ribbon and paper roll Power Connection Make sure the fuse you use is correct for the voltage source Appendix A Site Requirements Ribbon Loading Do not 2.Place the Ribbon Roll on the Ribbon Supply Spindle 3.Open the printhead by moving the handle to the OPEN posi- tion Important one: 6.Remove the Hook from the Ribbon Take-UpSpindle Page Media Loading Page Page Page Removing Used Ribbon Initial Printer Power Up Page Operation Page Page Page CANCEL Notes: Page Page Page Whenever the printer is reset to factory defaults, a Media Calibration procedure must be performedimmediately Label Format Qty Speed Page Configuration and Calibration Interconnections Page Configuration Mode IMPORTANT: Page Page Interconnections RS-232Serial Data Port Hardware Control Signal Descriptions RS-232Cabling Requirements To minimize electrical noise pickup in the cable: 1.Keep data cables as short as possible 2.Do not bundle the data cables tightly with power cords Page Data Signal Voltage Level Signal Descriptions Preventive Maintenance Page Page Page Toggle Positioning Printhead Pressure Adjustment Black-MarkMedia Sensor Position Adjustment Transmissive Media Sensor Position Adjustment Page Page 260M only: Page Media and Ribbon Sensor Sensitivity Adjustment Page Troubleshooting Page Page Page ^CC, ^CT, and ^CD Page Options Examples of these Optional Fonts can be found in Appendix D 220-240VAC Factory Setup Memory Options 6-Dot/mmPrinthead (200M Only) Page Page Appendix B - ASCII Code Chart Page Appendix C - Adjusting Bar Code Darkness Too Dark Slightly Dark Slightly Light Too Light In-Spec” Page Page Appendix D - Optional Printer Fonts Page Page Page Appendix E - Support Services Before you call Be prepared W.H. BRADY CO Customer Service Form Complete this form before requesting technical assistance Model # (Be specific: include ALL letters and numbers)