Manuals / Brands / Computer Equipment / Printer / Brady / Computer Equipment / Printer

Brady 200M, 260M Appendix A, Make sure the fuse you use is correct for the voltage source

1 104

Download 104 pages, 1.8 Mb

M-Series User ’s Guide	Installation

AC Power Fuse Replacement

A user-replaceable AC Power Fuse is located just above the Power ON/OFF Switch. (See Figure 2.1.) For a 100-120 VAC installation, the replacement fuse is a 3AG Fast Blow style rated at 5 Amp/250VAC. For a 220-240 VAC installation, the fuse is the same style but rated at 3 Amp/250VAC. Make sure the fuse you use is correct for the voltage source.

Before replacing the fuse, turn the AC Power Switch OFF and unplug the AC Power Cable.

To replace the fuse, insert the tip of a flat blade screwdriver into the slot in the end of the Fuse Holder End Cap. Press in slightly on the End Cap and turn the screwdriver slightly counter-clockwise. This will disengage the End Cap from the Fuse Holder and allow you to remove the fuse. To install a new fuse, reverse the procedure.

100-120 VAC Operation

1.Confirm that the voltage selector switch is set to 120 V.

2.Attach the supplied power cord to the AC power receptacle lo- cated on the rear of the printer.

3.Connect the opposite end of the power cord to a properly grounded source of 100-120 VAC (50 or 60 Hz) power rated for at least 5 Amps.

220-240 VAC Operation

1.Confirm that the voltage selector switch is set to 240 V.

2.Depending on how the printer was ordered, a power cord may or may not be provided for 220-240 VAC operation. If not pro- vided, obtain a cord set with the proper AC Power plug. The cord may then be connected to the standard (international)

IEC-type 3-prong AC connector provided on the M-Series Printer. Refer to Appendix A for more information.

2-3

Contents

Page BradyprinterTM THT Model 200M and 260M Thermal Transfer Printer USER'S GUIDE Proprietary Statement Product Improvements FCC Compliance Statement Canadian DOC Compliance Statement Liability Disclaimer Bradyprinter™ THT Models 200M and 260M WARRANTY INFORMATION 1. Printer Warranty 2. Supplies Warranty 3. Warranty Exclusions and Conditions Table of Contents Introduction Installation Operation Configuration and Calibration Interconnections Preventive Maintenance Troubleshooting Options Appendix A - 240 VAC Power Cord Appendix B - ASCII Code Chart Appendix C - Adjusting Bar Code Darkness Introduction Page Additional System Requirements Media and Ribbon Requirements run tests for your applications Warnings and Precautions CAUTION: CAUTION: Refer to the Interconnections Section Page Printer Specifications Printing Considerations Print Speeds Programmable constant printing speeds of 2″ (51 mm) 3″ (76 mm), 4″ (104 mm), 5“ (127 mm), and 6″ (152 mm) per second Media Ribbon Zebra Programming Language II (ZPL II®) Bar Codes Options Section Page Page Page Installation remove any ribbon and paper roll Power Connection Make sure the fuse you use is correct for the voltage source Appendix A Site Requirements Ribbon Loading Do not 2.Place the Ribbon Roll on the Ribbon Supply Spindle 3.Open the printhead by moving the handle to the OPEN posi- tion Important one: 6.Remove the Hook from the Ribbon Take-UpSpindle Page Media Loading Page Page Page Removing Used Ribbon Initial Printer Power Up Page Operation Page Page Page CANCEL Notes: Page Page Page Whenever the printer is reset to factory defaults, a Media Calibration procedure must be performedimmediately Label Format Qty Speed Page Configuration and Calibration Interconnections Page Configuration Mode IMPORTANT: Page Page Interconnections RS-232Serial Data Port Hardware Control Signal Descriptions RS-232Cabling Requirements To minimize electrical noise pickup in the cable: 1.Keep data cables as short as possible 2.Do not bundle the data cables tightly with power cords Page Data Signal Voltage Level Signal Descriptions Preventive Maintenance Page Page Page Toggle Positioning Printhead Pressure Adjustment Black-MarkMedia Sensor Position Adjustment Transmissive Media Sensor Position Adjustment Page Page 260M only: Page Media and Ribbon Sensor Sensitivity Adjustment Page Troubleshooting Page Page Page ^CC, ^CT, and ^CD Page Options Examples of these Optional Fonts can be found in Appendix D 220-240VAC Factory Setup Memory Options 6-Dot/mmPrinthead (200M Only) Page Page Appendix B - ASCII Code Chart Page Appendix C - Adjusting Bar Code Darkness Too Dark Slightly Dark Slightly Light Too Light In-Spec” Page Page Appendix D - Optional Printer Fonts Page Page Page Appendix E - Support Services Before you call Be prepared W.H. BRADY CO Customer Service Form Complete this form before requesting technical assistance Model # (Be specific: include ALL letters and numbers)