WSW03 (PABX* mode setting)
Selector | Function |
|
| Setting and Specifications | ||||
No. |
|
| ||||||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| CNG detection when sharing a |
|
|
|
|
|
|
|
1 | modular wall socket with a |
| 0: | A |
|
| 1: | B |
| telephone |
|
|
|
|
|
|
|
|
| No. | 2 | 3 | 4 |
|
|
|
|
|
| 0 | 0 | 0 | : | 50 ms | |
|
|
| 0 | 0 | 1 | : | 210 ms | |
2 | Min. detection time length of |
| 0 | 1 | 0 | : | 500 ms | |
PABX* dial tone, required for |
| 0 | 1 | 1 | : | 800 ms | ||
4 | starting dialing |
| 1 | 0 | 0 | : | 900 ms | |
|
|
| 1 | 0 | 1 | : | 1.5 sec. | |
|
|
| 1 | 1 | 0 | : | 2.0 sec. | |
|
|
| 1 | 1 | 1 | : | 2.5 sec. | |
|
|
|
|
|
|
|
|
|
| CNG detection when sharing a |
|
|
|
|
|
|
|
5 | modular wall socket with a |
| 0: | A |
|
| 1: | B |
| telephone |
|
|
|
|
|
|
|
|
| No. | 6 | 7 |
|
|
|
|
|
|
| 0 | 0 |
| : No detection | ||
|
|
|
|
|
|
| (3.5 sec. WAIT) | |
6 |
|
| 0 | 1 |
| : No detection | ||
| Dial tone detection in PABX* |
|
|
|
|
| (5 sec. WAIT) | |
7 |
|
| 1 | 0 |
| : No detection | ||
|
|
|
|
|
|
| (7 sec. WAIT) | |
|
|
| 1 | 1 |
| : Detection | ||
|
|
|
|
|
|
| (Frequency only) | |
8 | “R” key function | 0: 1st dial tone |
|
| 1: No 1st dial | |||
detection add |
| tone detection | ||||||
|
|
| ||||||
|
|
|
|
|
|
|
|
|
* PABX: Private automatic branch exchange
NOTE: Selectors 2 through 4 and 6 through 8 are not applicable where no PABX is installed.
•Selectors 1 and 5: CNG detection when sharing a modular wall socket with a telephone
These selectors determine whether or not the equipment detects a CNG signal when a line is connected to a telephone sharing a modular wall socket with the equipment. Upon detection of CNG signals by the number of cycles specified by these selectors, the equipment interprets CNG as an effective signal and then starts FAX reception.
Selector | Cycle | ||
No. 1 | No. 5 | ||
| |||
|
|
| |
0 (A) | 0 (A) | 0.5 cycle | |
0 (A) | 1 (B) | 1.0 cycle | |
1 (B) | 0 (A) | 1.5 cycles | |
1 (B) | 1 (B) | 2.0 cycles | |
|
|
|
•Selectors 2 through 4: Min. detection time length of PABX dial tone, required for starting dialing
Upon detection of the PABX dial tone for the time length set by these selectors, the equipment starts dialing.
These selectors are effective only when both selectors 6 and 7 are set to “1” (Detection).
V - 13