I-2 SmartCell 6A000/ZX-250 Reference Manual
Index
C
CACParams switch attribute..... 2-20 to 2-21
CACStat switch attribute...........2-22 to 2-23
cause codes
AAL parameters cannot be
supported...........................................B-2
Access information discarded...........B-2
Bearer capability not authorized.......B-2
Bearer capability not implemented... B-2
Bearer capability not presently
available............................................ B-2
Call control block not found............. B-3
Call rejected...................................... B-1
Calling party number not set.............B-3
Destination out of order.................... B-1
Identified channel does not exist...... B-2
Incompatible destination...................B-2
Incorrect message length.................. B-2
Information element non-existent
or not implemented.........................B-2
Internal resource error.......................B-3
Invalid call reference value...............B-2
Invalid endpoint reference................ B-2
Invalid information element contentsB-2
Invalid number format...................... B-1
Invalid transit network selection.......B-2
Link not active.................................. B-3
Link not found.................................. B-3
Mandatory information element is
missing.............................................. B-2
Message not compatible with call
state................................................... B-2
Message type non-existent or not
implemented ..................................... B-2
Network out of order........................ B-2
No response from network................B-2
No response to connect.....................B-2
No response to out-going call processB-2
No response to restart request...........B-3
No route to destination......................B-1
No route to specified transit networkB-1
No user responding........................... B-1
No VPI/VCI available.......................B-2
Normal cell clearing......................... B-1
Normal, unspecified..........................B-1
Number changed............................... B-1
Protocol error, unspecified................B-2
Quality of Service unavailable.......... B-2
Recovery on timer expire..................B-2
Requested VPI/VCI not available.....B-1
Resource unavailable, unspecified....B-2
Response to STATUS ENQUIRY.... B-1
SAP not active ..................................B-3
Service or option not available,
unspecified........................................B-2
Temporary failure............................. B-2
Too many pending add party requestsB-2
Unassigned number...........................B-1
Unsupported combination of traffic
parameters......................................... B-2
User busy .......................................... B-1
User cell rate not available................B-1
User cell rate unavailable..................B-2
User rejects all calls with calling
line identification.............................. B-1
VPI/VCI assignment failure..............B-1
VPI/VCI pair is unacceptable........... B-1
CCTm...................................................2-175
Cell Memory Size.................................2-185
change default boot load image................3-3
changing switch start-up behavior............3-1
changing the boot load default.................3-1
Chnl DVT.............................................2-164
chpi...........................................................3-3
clear
config...............................................2-39
clear flash file system...............................3-4
clear switch configuration........................3-4
clfs............................................................3-4
Client Address........................................2-24
Client State.............................................2-24
Client Type.............................................2-30
ClientNumber............2-24, 2-28, 2-30, 2-35,
.......................... 2-56, 2-58, 2-61, 2-64, 2-66
command defined.....................................1-1
Common DRAM.................................. 2-185
Community Name .................................. 2-37
Config.....................................................2-39
Configuration Errors...............................2-79
Configured VCI Bits ............................2-133
Configured VPI Bits.............................2-133
Conn SubId............................... 2-149, 2-177
ConnectionCompeteTime.......................2-84
ConnectMethod................... 2-13, 2-41, 2-94
ConnId...................................... 2-149, 2-177
ConnType................................. 2-148, 2-178