Attaching the Cables to the Switch | Cisco Systems 3560-C instruction

Chapter 2 Switch Installation

Installing the Cable Guard (Optional)

Figure 2-31 Attaching the Cables to the Switch

2

SYST

STAT

DPLX

1

MODE

SPD

2

3

Catalyst

2960-C

PoE

4

5

Series

PD

CONSOLE

PD

6

7

8

PO

WER

OVER

ETHERNET

1

2

1

208918

1

Cable guard

2

Pivot direction for cable guard pivots

Step 4 Guide the connected cables through the slots in the front of the cable guard. Slide the cable guide in as shown in Figure 2-33. Tighten the screws.

Figure 2-32 Guiding the Cables through the Guard

330040

	Catalyst 3560-C and 2960-C Switch Hardware Installation Guide
2-30	OL-23803-02

Image 56

Cisco Systems 3560-C manual Attaching the Cables to the Switch

Contents

Americas Headquarters Text Part Number OL-23803-02Page N T E N T S Switch Installation Switch LEDs OL-23803-02 Preface Obtaining Documentation and Submitting a Service Request Related Publications Switch Models Switch Model Description Front Panel 3 4 Catalyst 3560CPD-8PT-S Front Panel View PoE Ports Switches with PoE Ports 10/100 and 10/100/1000 Fast Ethernet Downlink Ports PoE Pass-Through PoE Pass-Through PoE Budgeting for the Catalyst 2960CPD-8PT-L USB Type a Port Dual-Purpose PortsSFP Modules GLC-FE-100FX= GLC-FE-100LX= GLC-FE-100BX-D= Management Ports USB Mini-Type B Port Switch Panel LEDs LEDs System LED Console LEDsColor System Status Color Description Port Mode Description Port status Port status. This is the default modeModes for Port LEDs Port LEDs Color Meaning PoE LEDDual-Purpose Port LEDs Security slot Power adapter connector Reset button Rear Panel Auxiliary power adapter Internal Power SupplyAuxiliary Power Adapter Security Slots Reset ButtonManagement Options Network Configurations Cisco IOS CLI Switch Installation Preparing for Installation Statement Installation Guidelines Equipment That You Supply Powering the SwitchBox Contents Verifying Switch Operation Mounting the Switch Desk- or Shelf-Mounting On a Desk or Shelf without Mounting ScrewsDesk, Shelf, or Wall with Mounting Screws Installing the Mounting Screws on Top of a Desk or a Shelf Mounting the Switch on Top of a Desk or Shelf Under the Desk- or Shelf-Mounting Installing the Mounting Screws Under a Desk or Shelf Desk or shelf Screws Screw template Adhesive Wall-Mounting Desk or shelf Slides on this way 77 in .49 cm 72 in .44 cm 46. 62 in .19 cm Switch Location of the Mounting Holes on the Switch Installing the Mounting Screws on the Wall With a Mounting Tray Mounting Tray with Screws Switch Mounting tray Sliding direction Desk Installing the Switch on the Mounting Tray Switch Number-10 Phillips pan-head screws Mounting Tray with a Magnet Place the switch on the mounting tray. See Figure 11 Placing the Switch on the Mounting Tray 13 Wall-Mounting with a Magnet Phillips flat-head screw Attaching Brackets to the SwitchA Rack Mounting the Switch in a Rack 15 Attaching the 23-inch Brackets for Rack-Mounting Attaching the DIN-Mount Tray to the Switch Place the switch on the DIN rail mount. See FigureSwitch DIN rail mount On a DIN Rail Mounting the Switch on a DIN Rail 18 Securing the DIN-Mount Tray to the Switch 19 Mounting the Switch on a DIN Rail Removing the Switch from a DIN Rail Installing a Cover for the Reset Button Optional Switch Reset button cover Installing the Power Cord Retainer Optional 23 Inserting the Retainer through the Lanced Loop AC power cord Latches Sleeve for thin power cords Slide the retainer through the first latch. See Figure 26 Sleeve Around the Power Cord Installing the Cable Guard Optional Washer 29 Attaching the Cable Guard to the Switch 31 Attaching the Cables to the Switch Number-8 Phillips wood screws Desk or shelf After Installing the SwitchInstalling SFP Modules Removing SFP Modules TX and which is receive RXInsert a dust plug into the optical ports of the SFP module Grasp the SFP module, and carefully remove it from the slot Bale clasp Connecting Devices to the Ethernet PortsConnecting to the 10/100 and 10/100/1000 Ports Connecting to the PoE Ports Device Crossover Cable Where to Go Next OL-23803-02 Diagnosing Problems Switch Post Results Switch LEDs Switch ConnectionsBad or Damaged Cable Ethernet and Fiber-Optic Cables Interface Settings 10/100 and 10/100/1000 Port Connections10/100 PoE or PoE+ Port Connections SFP Module Switch Performance Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface Cards Resetting the Switch Finding the Switch Serial Number Serial Number Location for the Catalyst 3560CPD-8PT-S Switch 330039 OL-23803-02 Technical Specifications Environmental Ranges Environmental Ranges Physical Specifications Power Requirements Table A-2 Catalyst 3560-C and 2960-C Switch Specifications Switch Available PoE OL-23803-02 Connector Specifications 10/100 and 10/100/1000 Ports SFP Module Connectors Figure B-2 10/100/1000 Port Pinouts Core Modal Wavelength Cables and AdaptersSFP Module Cables Cable Pinouts TP3 Device Switch Console RJ-45-to-DB-9 Port DTEConsole Port Adapter Pinouts RxD TxD Switch Console RJ-45-to-DB-25 Port DTE Adapter DeviceTxD RxD Accessing the CLI Through the Console Port RJ-45 Console Port Figure C-1 Connecting the Console Cable Figure C-2 Connecting the USB-Mini Console Cable USB Mini-Type B Console Port Installing the Cisco Microsoft Windows USB Device Drivers Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Using the Add or Remove Programs Utility Completing the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable secret password, and press Return Enter an enable password, and press ReturnEnter a virtual terminal Telnet password, and press Return Switch or as a standalone switch These choices appear OL-23803-02