Switch Installation | Cisco Systems Cisco ME 3400E specification

Chapter 2 Switch Installation

Warnings

Warning The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device. Statement 1019

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection. 10/100/1000 Ethernet Statement 1044

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning No user-serviceable parts inside. Do not open. Statement 1073

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

Caution To comply with the Telcordia GR-1089 Network Equipment Building Systems (NEBS) standard for electromagnetic compatibility and safety, connect the Ethernet cables only to intrabuilding or nonexposed wiring or cabling.

Note The grounding architecture of this product is DC-isolated (DC-I).

You can use the grounding lug to attach a wrist strap for ESD protection during servicing.

Cisco ME 3400E Ethernet Access Switch Hardware Installation Guide

	OL-16447-01	2-3

Image 27

Cisco Systems Cisco ME 3400E manual Switch Installation

Contents

Text Part Number OL-16447-01 Americas HeadquartersPage N T E N T S Installing the Switch Rack-Mounting Link Status IP Settings C-2 Purpose Audience Viii Related Publications Obtaining Documentation and Submitting a Service Request OL-16447-01 Switch Models Setting Up the Switch Front Panel Switch Model Description Cisco ME 3400EG-12CS-M Front Panel Alarm Input Port AC- and DC-Power Input Connectors SFP Modules Management Port10/100 Fast Ethernet Ports Dual-Purpose Ports Part Number Description SFP Module Patch Cable LEDs UNIs, NNIs, and ENIs Color System Status Switch LED Panels Switch Power-Supply LEDs Power-Supply Module LEDs Ethernet Management Port LED LED Color Meaning Alarm LEDsPort LEDs Dual-Purpose Port LEDs Rear Panel Power-supply slot Ground connection 11 Cisco ME 3400EG-2CS-A Rear Panel Power Supply Features Management Options Network Configurations Switch Installation Switch Installation Switch Installation Installation Guidelines Verifying Switch Operation Installing the SwitchPowering Off the Switch Rack-Mounting Removing Screws from the Switch Rack-Mounting Brackets Attaching Brackets to the Switch Attaching Brackets for 19-Inch Racks Attaching Brackets for 19-Inch, 23-Inch, and 24-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for 24-Inch Racks Attaching Brackets for Etsi Racks Mounting in a Rack Mounting in a Rack Attaching Brackets for Wall-Mounting Wall-Mounting Mounting the Switch on a Wall Cisco ME 3400EG-12CS-M Cisco ME 3400E-24TS-M Cisco ME 3400EG-2CS-A Installing and Removing SFP Modules Installing SFP ModulesTable- or Shelf-Mounting 16 SFP Module with a Bale-Clasp Latch Removing SFP Modules Inserting and Removing the SFP Module Patch Cable Removing the SFP Module Patch Cable Connecting to the 10/100 and 10/100/1000 Ports 21 Connecting to an Ethernet Port 22 Connecting to a Fiber-Optic SFP Module Port Connecting to Fiber-Optic SFP Modules 23 Connecting to a 1000BASE-T SFP Module Connecting to 1000BASE-T SFP Modules Where to Go Next Connecting to Dual-Purpose Ports Power-Supply Module Description Product OverviewModel number Description PSU OK LED Handle-Side Description PSU OK DC-Power-Supply Module Power-Supply Module InstallationConnector-Side Description AC-Power-Supply Module Tools and Equipment Installation Guidelines AC-1 PSU-1 AC-2 PSU-2 Installing an AC-Power-Supply Module AC-Power Supply and Power-Cord Retainer in a Switch Removing AC-Power-Supply Modules Installing a DC-Power-Supply Module Grounding the Switch Preparing for Installation Remove the ground screw from the switch rear panel 12 Attaching the Ground Lug and Wire Assembly Installing the DC-Power-Supply Module in the Switch Statement Wiring the DC-Input Power Source 15 Terminal Block Plug 18 Inserting Wires in the Terminal Block Plug 21 Inserting the Terminal Block in the Block Header 22 DC-Power Terminal Block With Two Feeds Removing the DC-Power-Supply Module Power Supply Settings OL-16447-01 Switch Post Results Diagnosing Problems Ethernet and Fiber Cables Switch LEDsSwitch Connections Bad or Damaged Cable Spanning Tree Loops SFP Module Port IssuesPort and Interface Settings Ping the End Device Autonegotiation and NICs Clearing the Switch IP Address and ConfigurationSwitch Performance Speed, Duplex, and Autonegotiation Serial Number Location on the Cisco ME 3400E-24TS-M Finding the Switch Serial Number OL-16447-01 SFP Module 32 to 131F 0 to 55C 32 to 140F 0 to 60C Environmental Ranges 32 to 149F 0 to 65C With 1 Power-Supply With 2 Power-Supply SFP Module Modules 32 to 149 F 0 to 65C Physical Dimensions AC-Power RequirementsDC-Power Requirements Physical Dimensions Power Specifications Physical Specifications Power Specifications OL-16447-01 10/100 Connector Specifications Figure B-2 Fiber-Optic SFP Module LC Connector SFP Module Connectors Figure B-3 10/100/1000 Port Pinouts 10/100 Ethernet Management Port Bandwidth SFP Module Wavelength nanometers Fiber Type Cables and AdaptersSFP Module Cables Core Modal 1000BASE-SX Figure B-6 Cable Pinouts DSR DTR CTS RTS Console Port Adapter Pinouts Switch Console RJ-45-to-DB-25 Port DTE Starting the Terminal-Emulation Software Accessing the CLI Through the Console Port Entering the Initial Configuration Information IP SettingsCompleting the Setup Program Enter an enable secret password, and press Return These choices appear Numerics IN-2 IN-3 IN-4 IN-5 IN-6