Editing the Dual WAN and Multi-WAN Settings | Cisco Systems RV016

5

Editing the Dual WAN and Multi-WAN Settings

The Dual WAN Settings page (Multi-WAN Settings on RV016) appears after you click the Edit icon for a WAN interface on the Dual WAN (or Multi-WAN) page. Enter the interface settings, as needed.

NOTE Before navigating away from this page, click Save to save your settings, or click Cancel to undo them. Any unsaved changes are abandoned.

Max Bandwidth Provided by ISP:

In this section, enter the maximum bandwidth settings as specified by your Internet Service Provider. If the bandwidth exceeds the specified number, then the router uses another WAN interface for the next connection.

•Upstream: Enter the maximum upstream bandwidth provided by your ISP. The default is 512 kbit/sec.

•Downstream: Enter the maximum downstream bandwidth provided by your ISP. The default is 512 kbit/sec.

Network Service Detection:

Optionally, check the box to allow the router to detect network connectivity by pinging specified devices. Then enter the settings below. Uncheck the box to disable this feature.

•Retry count: Enter the number of times to ping a device. The default is 5.

•Retry timeout: Enter the number of seconds to wait between pings. The default is 30 seconds.

•When Fail: Choose the action that will be taken if a ping test fails. If you choose Generate the Error Condition in the System Log, the router

Cisco Small Business RV0xx Series Routers Administration Guide

77

Image 77

Cisco Systems RV016 Editing the Dual WAN and Multi-WAN Settings, Max Bandwidth Provided by ISP, Network Service Detection

Contents

Administration Guide Cisco Systems, Inc. All rights reserved 78-19576-01 B0 Other Hardware Features Viewing System Summary Information SetupPlacement Tips Introduction System Management DhcpPort Management Firewall Logging System Statistics 153 VPN 122 Appendix H Where to Go From Here 199 Appendix G Specifications 189Appendix E IPSec NAT Traversal 183 Appendix F Bandwidth Management 186 Model RV0xx Series Router FeaturesPorts RV042 and RV042G RV082 RV016 RV042 and RV042G Ports IntroductionRV042 and RV042G Status Lights RV082 Ports and Status Lights Port Description Ports Light Description Status Lights Feature Description Other Hardware Features Placement Tips Default SettingsDesktop Placement Parameter Default Value RV042 and RV042G 58 mm apart RV082 and RV016 94 mm apart Wall Mounting Rack Mounting RV082 or RV016 RV042 and RV042G Internet Port Connecting the EquipmentRV082 Internet Port RV016 Internet 1 Port Getting Started with the Configuration Troubleshooting Tips Navigation Features of the User Interface Saving the Settings Setup WizardsPop-Up Windows Help Viewing System Summary Information Viewing System Summary Information System InformationCisco ProtectLink Web Port Information Window ConfigurationPort Statistics Viewing System Summary Information WAN information WAN Status VPN Setting Status Firewall Setting StatusLog Setting Status DMZ information Setup Host Name and Domain Name Setting Up the NetworkSetup Changing the device IP address IP ModeLAN Setting device IP address and subnets Enabling multiple subnets IPv4 only Setup WAN Setting Internet connection DMZ Setting Setup Editing a WAN Connection Page Page Page IPv4 IPv6 Editing a DMZ ConnectionPage Changing the Administrator Username and Password Setup To open this page Click Setup Time in the navigation tree Setting the System Time Setting Up a DMZ Host Port Range Forwarding, Port Triggering, Setting Up Port Forwarding and Port TriggeringPort Range Forwarding Setup Adding a service Port Triggering To open this page Click Setup UPnP in the navigation tree Setting Up Universal Plug and Play UPnP Setup Adding a service Setting Up One-to-One NAT Setup Cloning a MAC Address for the Router Editing the MAC Address Clone Settings Assigning a Dynamic DNS Host Name to a WAN Interface Editing the Dynamic DNS Setup Configuring Dynamic Routing, Configuring Static Routing, Setting Up Advanced Routing Data None, RIPv1, RIPv2 Broadcast, or RIPv2 Multicast Configuring Dynamic RoutingDynamic Routing for IPv4 Prefix Length Pv6 only Enter the prefix length Configuring Static RoutingDynamic Routing for IPv6 Setting Up Advanced Routing IPv6 Transition To Go From Here Dhcp Setting Up the Dhcp Server or Dhcp Relay Dhcp Wins used for Dhcp Server, IPv4 Only Dynamic IP used for Dhcp Server onlyDNS used for Dhcp Server only Assigning static IP addresses by adding devices from a list About Static IP Addresses for IPv4 Only Assigning static IP addresses by entering devices manually Using the Static IP List to Block Devices DNS Local Database Client Table Viewing the Dhcp Status InformationDhcp Server Router Advertisement IPv6 Dhcp System Management Setting Up Dual WAN and Multi-WAN Connections System Management Mode Cisco RV042, RV042G, and RV082 Mode Cisco RV016 Interface Setting Max Bandwidth Provided by ISP Editing the Dual WAN and Multi-WAN SettingsNetwork Service Detection Page Adding a service Page Max Bandwidth Provided by ISP Managing the Bandwidth SettingsBandwidth Management Type Appendix F, Bandwidth Management Managing the Bandwidth Settings Adding a service Setting Up Snmp Enabling Device Discovery with Bonjour Enabling Device Discovery with Bonjour DNS Name Lookup Using Built-In Diagnostic ToolsTo open this page Click System Management Diagnostic Ping Restoring the Factory Default Settings Upgrading the Firmware Restarting the Router Restoring the Settings from a Configuration File Backing Up and Restoring the Settings Copying a Startup File or Mirror File Backing Up Configuration Files and Mirror Files Backing Up and Restoring the Settings Port Management Configuring the Port Settings Port Management Summary Viewing the Status Information for a Port Statistics Firewall Configuring the General Firewall Settings Firewall Restrict Web Features Firewall About Access Rules Configuring Firewall Access Rules Managing Access Rules To delete all custom rules Click Restore to Default Rules Services IPv4 and IPv6 Configuring Access Rules Schedule IPv4 Only Adding a service Page Forbidden Domains, Website Blocking by Keywords, Schedule, Using Content Filters to Control Internet Access Website Blocking by Keywords Forbidden Domains Schedule Getting Started with Cisco ProtectLink Web Cisco ProtectLink Web Cisco ProtectLink Web Specifying the Global Settings for Approved URLs and Clients Approved Clients Configuration Approved URL ConfigurationApproved URLs and Approved Clients To delete an entry Click the Delete icon Web Protection Enabling Web Protection for URL Filtering URL Filtering Web Reputation Business Hour Setting URL Overflow Control Updating the ProtectLink License License Information License Introduction to VPNs VPN Configuration tasks Remote Access Client To GatewaySite to Site VPN Gateway To Gateway Gateway-to-Gateway VPN Tunnel Between RV0xx Series Routers Router QuickVPN, page125 and Remote Access with PPTP, page125 Remote Access with Pptp Remote Access with Cisco QuickVPN To open this page Click VPN Summary in the navigation tree Viewing the Summary Information for VPN Tunnel Status GroupVPN Status Up a Remote Access Tunnel for VPN Clients Client To Gateway, VPN Clients Status Setting Up a Gateway to Gateway Site to Site VPN Add a New Tunnel Local Group Setup and Remote Group Setup VPN IPSec Setup Required fields for Manual mode Preshared Key, page 135 and Advanced settings for IKE with Required fields for IKE with Preshared Key Advanced settings for IKE with Preshared Key VPN VPN RV0xx Local Group Setup Remote Client Setup for Single User Tunnel Type VPN IPSec Setup Required fields for IKE with Preshared Key Advanced settings for IKE with Preshared Key VPN Users, Certificate Management, page148 Managing VPN Users and Certificates Certificate Management Users Setting Up VPN Passthrough Setting Up Pptp Server Pptp Server IP Address Range Connection List Syslog section, Mail section, Setting Up the System Log and Alerts Syslog section Log Setting, Buttons,Mail section Logging System Statistics Log Setting Buttons Viewing the System Log Logging System Statistics Wizard Basic Setup, Access Rule Setup, page160 Wizard Basic SetupAccess Rule Setup Beacon interval Term DefinitionDtim Delivery Traffic Indication Message Glossary Term Definition Advertisement Daemon Radvd RouterRequest to Send RTS Threshold Vlan Virtual LAN RIPng RIP next generationStatic routing Your computer cannot connect to the Internet Firmware upgrade has failed Router does not have a coaxial port for the cable connection Troubleshooting Introduction Cisco QuickVPN for Windows Cisco QuickVPN for Windows Cisco QuickVPN Client Installation and ConfigurationUsing the Cisco QuickVPN Software Using the Cisco QuickVPN Software Topology Options Hub and Spoke VPN Hub and Spoke Topology Mesh VPN Mesh Topology Other Design Considerations WAN Setup Gateway To Gateway Tunnel with a Dynamic IP Address LAN Setup Configuring a VPN Tunnel on a Cisco RV0xx Series Router Field Value Settings on the Site a RouterExample Sites with Static WAN IP Addresses MD5 Encryption Phase Encryption Field Values Example Site with a Dynamic WAN IP Address Authentication Field Value IPSec Setup Keying Mode IKE with Preshared Key Phase Overview IPSec NAT Traversal IPSec NAT Traversal Configuration of Router a Configuration of Router B Click Add to List Creation of New ServicesClick the System Management tab Bandwidth Management Creation of New Bandwidth Management Rules Click Save RV042 SpecificationsPerformance Security QoS SpecificationsNetwork Environmental RV042GManagement Operating System Linux VPN Cisco RV082 IKE Cisco RV016 Dhcp DNS NAT DMZ Built-in Pptp server supporting 10 Pptp clients Cisco Small Business SupportProduct Documentation