LCD Programming, LCD menu tree | ClearOne comm PSR1212 guide

Installation ~ LCD Programming

LCD Programming

The PSR1212’s front panel is intuitive to operate, thanks to its simple interface: a 2x16 character LCD, menu buttons, and a peak-level LED bar meter. Although most of the PSR1212’s features are programmed with G-Ware software (see page 23), the front panel can be used for simple adjustments and meter monitoring.

When power is applied to the PSR1212, the LCD panel will first read INITIALIZING. If an error is displayed, contact technical support. When initialization is complete, “PSR1212” is displayed on the top line and “Unit 0” is displayed on the bottom line.

LCD menu tree

The menu tree features five main menus, each with submenus. These branches typically end when an adjustable parameter or viewable value is reached. The diagram below shows the LCD menu tree.

✍

✍

13

G-Ware software is required to complete system setup.

Pressing Esc at the top of the tree does nothing.

Figure 2.6. LCD menu tree

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 19

ClearOne comm PSR1212 LCD menu tree, Installation ~ LCD Programming, Pressing Esc at the top of the tree does nothing

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No June 2002 Rev Table of Contents System Configuration Advanced Configuration Appendices Control Technical Services Group ~ 1-800-283-5936 USA ~ Product overview Introduction New Features ClearOne Communications EuMEA GmbH Professional Services GroupSales and Customer Service Technical Support Controls and Connections UnpackingFront panel Introduction ~ Controls and Connections Rear panel Introduction ~ Controls and Connections Expansion bus Networking Environmental PowerEquipment placement Operational Requirements Hardware Setup Installation To connect the unit Installation ~ Hardware Setup To create an expansion bus network Installation ~ Networking UnitsNetworking Units Expansion bus connections To assign device IDs Mixer modeTo select a mixer mode Device IDs Pressing Esc at the top of the tree does nothing Installation ~ LCD ProgrammingLCD Programming LCD menu tree Run Macro To adjust a parameterSelect Preset System menu RS-232 menu Flow Control hardware Enable ModemClear Password Meter menu Inputs menu Gain Outputs menu Matrix Technical Services Group ~ 1-800-283-5936 USA ~ Ware Requirements System Configuration To install G-Ware Installing G-WareCreating Floppy Disk Copies Creating a new site Site SetupTo create a new site Select the PSR1212 icon and click Add Adding a PSR1212To auto-detect units To manually add units To configure Unit Properties Configuring Unit Properties System Configuration ~ Site Setup Ware Screens System Configuration ~ G-Ware ScreensFlow Screen Safety Mute Copying and pasting settingsStatus bar 20. G-Ware Matrix Screen Matrix Screen Cross point attenuation Audio RoutingExpansion bus O-Z routing Process A-H routing Matrix report System Configuration ~ Audio Routing Inputs Inputs and Outputs Type Pwr Phantom PowerFilters Active Filter Table View NOM count Manual Off deactivates the mic To configure filtersGate Activation Gate Ratio PA Adaptive ModeChairman Override Adaptive Ambient PA Adapt and AEC Reference Decay Rate Click Close to exit the window To create a virtual reference Gating Group Select To configure gating group settingsTo assign a gating group Min/Max limits Click the Gating Group label to change the group names Meters 38. Inputs 9-12 Configuration window 40. Gain meters NOM Outputs Optimizing output gain structure From Expansion Bus O-Z Expansion BusesTo Expansion Bus O-Z Processing A-H Processing Compressors Cmprs compressorGroup 47. Processing Filters window Remove Filter PhaseBypass Add Filter Changes you make in the distance and temperature fields Delay Optimizing process gain structure 50. Process Gain adjust and meter Creating Presets PresetsOverview Affected when the preset is run Preset Configuration panePreset password is set in the Unit Properties window see Advanced Configuration ~ Presets Assigning virtual references to the preset Storage space To create a preset To run a preset using front panel control Running presetsRunning multiple presets simultaneously To run a preset using G-Ware Room combining example All presets are ready to run again Four macros one for each configuration are set up as follows Macros To create a macro using Macro RecorderCreating macros 16 Macro Name window To create a macro using Macro Editor To delete a macro To add or insert a command lineEditing macros To edit a macro Running macros To run a macro using G-WareTo run a macro using front panel control To run a macro using the Select panel or Gpio Select the PSR1212 Unit and Input Channel you want to use Signal GeneratorUtilities To use pink or white noise To use tone Document Compare UtilityTo compare site files Open window Operation ~ Utilities Print Preview window Copying settings Print Reports window Print Reports Button To upgrade firmwareGFirm Firmware Utility Toolbar 13. Selecting baud rate Copy and paste settings Ware SwitcherTo use G-Ware Switcher Operation ~ Monitoring Views Message LogMonitoring Views Gate View Meter Views To configure Meter Views Gpio Builder To program control/status pinsControl/Status a XAP IR Remote Remote BuilderControl ~ Remote Builder ClearOne Control Panels Select IR Remote default from the Select Remote Type listControl ~ Remote Builder To program the XAP IR Remote Control ~ Remote Builder To program the Volume panel Select Panel selected in the Remote Builder To program the Select panel Serial commands Remote Modem AccessRS-232 Port Control ~ RS-232 Port Command stringsTo create a command string To run a command string Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Pin Number Control All nine pins be connected toAppendix B Pinouts Pin Number Appendices ~ Appendix B Pinouts Control/Status connectorsPin Definable Type Default Description First 16 pins on Control/Status B port pinout Preset select bit+5VDC, 300mA Pin Description RS-485 Remote Panel a and B connectorsSet connector pinout Line connector pinout Appendix C Control Panel Connecting the Control Panel 800 ft/244 m Appendices ~ Appendix C Control Panel Figure C.6. Volume Control Panel Assembly Appendices ~ Appendix D Accessories Appendix D AccessoriesAccessory ClearOne Part Number Example Appendix E Serial CommandsCommand structure Conventions Unit type Appendices ~ Appendix E Serial CommandsGroups and channels Type and device IDs Error number Text message Explanation/Solution Serial command error codesMeter type definitions Command Function PSR1212 Serial commands Channels Selects/reports NOM setting on outputSelects/reports off attenuation mode for Selects/reports signal generator activation Argument details Aamb Adaptive Ambient ModeAmblvl Ambient Level Adjust AGC Automatic Gain Control Baud Baud Rate Chairo Chairman Override ModeCgroup Compressor Group Select Compsel Compression Select Compress Compressor AdjustGain of 3dB 100 Decay Decay AdjustDelay Delay Adjust Delaysel Delay Select Channel Group Dfltm Default Meter101 Did Device ID Name Description Units Filter Filter Adjust102 Examples Flow Flow Control FMP First Mic Priority Mode103 Filtsel Filter Select Button assignment Gain Gain Adjustment104 FPP Front Panel Passcode Example GHOLD- Gate Hold Time Adjust105 Gate Gate Status Gover Gating Override Gmode Gating ModeGratio Gate Ratio Adjust 106 107 Greport Gate ReportGrpsel Gating Group Select Label Label LFP Lock Front Panel LMO Last Mic On ModeLock Preset and Macro Lock 108 LVL Level Lockprst Apply the lock to a preset or macroLockpwd Set preset/macro password 109 = Toggle 110Lvlreport Level Report Lvlrrate Level Report Rate Macro Macro Execution/Reporting Master Expansion Bus Master ModeMAX Maximum Gain Setting This setting will affect all relative gain adjustments MIN Minimum Gain Setting Mdmode Modem Mode112 113 Minmax Minimum and Maximum Gain SettingMinit Modem Initialization String Mmax Maximum Number of Microphones Mline Mic/Line AdjustMpass Modem Password 114 115 Mtrxlvl Matrix Attenuation AdjustmentMtrx Matrix Mute Mute NOM Number of Open Microphones ModeOffa Off Attenuation Mode 116 117 PAA PA Adaptive ModePP Phantom Power Preset Preset Execution/Reporting String location 118Prgstring Program String Supported special characters Name Description Unit Ramp Ramp Gain Adjustment119 Refsel PA/AEC Reference Select Serecho Serial Echo Refset Reference channel setupSermode Serial Mode 120 Siggen Signal Generator Sftymute Safety mute121 Tout Time Out Select Sigtout Signal Generator Time Out122 String String Execution VER Version Command Value Null to return value123 UID Unit ID 124 Appendix F Warranty 125 Appendices ~ Appendix F Warranty FCC Part 15 Compliance Safety Information126 Appendix G Compliance Glossary 127 Glossary 128 129 130 131 132 133 134 Signal Delay Used for 135 Index 136 Index 137 138 PhaseFrequency response 139