Greport Gate Report, Label Label, 107 | ClearOne comm PSR1212

Appendices ~ Appendix E: Serial Commands

GREPORT - Gate Report

This command selects/reports the gate status.

Command form: DEVICE GREPORT <Value>

Argument details

Name	Description
Device	0–7 or * to select all units
GREPORT	Command form
Value	0 = Off, 1 = On, 2 = Toggle

Example: #43 GREPORT 1 On PSR1212 unit 3 (#43), the gate reporting

(GREPORT) is set to on (1).

GRPSEL - Gating Group Select

This command selects/reports which gating group each input is assigned. There can be only one selection per input.

Command form: DEVICE GRPSEL <Channel> [Value]

Argument details

Name	Description
Device	0–7 or * to select all units
GRPSEL	Command form
Channel	1–8 (selects mic input)
Value	1–4, A–D (selects gating group), Null to return current value

Example: #44 GRPSEL 1 A On PSR1212 unit 4 (#44), mic channel 1 is assigned to gating group (GRPSEL) A.

LABEL - Label

This selects/reports the label of the specific channel identified in the unit. Command form: DEVICE LABEL <Channel><Group>[In/Out] [String]

Argument details

Name	Description
Device	0–7 or * to select all units
LABEL	Command form
Channel	See Groups and Channels, page 93
Group	I, O, M, G, P, L, E, U, W, S, C (see page 93)
In/Out	0 = Output, 1 = Input (For expansion bus groups only)
String	String of up to 20 characters representing the label text.
	Null to query and CLEAR to clear the label

Example: #47 LABEL 1 M WIRELESS On PSR1212 unit 7 (#47), the label (LABEL) for mic (M) channel 1 is WIRELESS.

✍

report

107

Gate report sends a report on every gate change. If no mics are gated on, the will be sent every 10 seconds.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 113

ClearOne comm PSR1212 operation manual Greport Gate Report, Grpsel Gating Group Select, Label Label, 107

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No June 2002 Rev Table of Contents System Configuration Advanced Configuration Appendices Control Technical Services Group ~ 1-800-283-5936 USA ~ Product overview Introduction New Features Sales and Customer Service Professional Services GroupTechnical Support ClearOne Communications EuMEA GmbH Front panel UnpackingControls and Connections Introduction ~ Controls and Connections Rear panel Introduction ~ Controls and Connections Expansion bus Networking Equipment placement PowerOperational Requirements Environmental Hardware Setup Installation To connect the unit Installation ~ Hardware Setup Networking Units Installation ~ Networking UnitsExpansion bus connections To create an expansion bus network To select a mixer mode Mixer modeDevice IDs To assign device IDs LCD Programming Installation ~ LCD ProgrammingLCD menu tree Pressing Esc at the top of the tree does nothing Select Preset To adjust a parameterSystem menu Run Macro RS-232 menu Clear Password Enable ModemMeter menu Flow Control hardware Inputs menu Gain Outputs menu Matrix Technical Services Group ~ 1-800-283-5936 USA ~ Ware Requirements System Configuration Creating Floppy Disk Copies Installing G-WareTo install G-Ware To create a new site Site SetupCreating a new site To auto-detect units Adding a PSR1212To manually add units Select the PSR1212 icon and click Add To configure Unit Properties Configuring Unit Properties System Configuration ~ Site Setup Flow Screen System Configuration ~ G-Ware ScreensWare Screens Status bar Copying and pasting settingsSafety Mute 20. G-Ware Matrix Screen Matrix Screen Expansion bus O-Z routing Audio RoutingProcess A-H routing Cross point attenuation Matrix report System Configuration ~ Audio Routing Inputs Inputs and Outputs Filters Pwr Phantom PowerActive Filter Type Table View Gate To configure filtersActivation NOM count Manual Off deactivates the mic Chairman Override PA Adaptive ModeAdaptive Ambient Gate Ratio PA Adapt and AEC Reference Decay Rate Click Close to exit the window To create a virtual reference To assign a gating group To configure gating group settingsGating Group Select Min/Max limits Click the Gating Group label to change the group names Meters 38. Inputs 9-12 Configuration window 40. Gain meters NOM Outputs Optimizing output gain structure To Expansion Bus O-Z Expansion BusesFrom Expansion Bus O-Z Processing A-H Processing Group Cmprs compressorCompressors 47. Processing Filters window Bypass PhaseAdd Filter Remove Filter Changes you make in the distance and temperature fields Delay Optimizing process gain structure 50. Process Gain adjust and meter Overview PresetsCreating Presets Preset password is set in the Unit Properties window see Preset Configuration paneAffected when the preset is run Advanced Configuration ~ Presets Assigning virtual references to the preset Storage space To create a preset Running multiple presets simultaneously Running presetsTo run a preset using G-Ware To run a preset using front panel control Room combining example All presets are ready to run again Four macros one for each configuration are set up as follows Creating macros To create a macro using Macro RecorderMacros 16 Macro Name window To create a macro using Macro Editor Editing macros To add or insert a command lineTo edit a macro To delete a macro To run a macro using front panel control To run a macro using G-WareTo run a macro using the Select panel or Gpio Running macros Utilities Signal GeneratorTo use pink or white noise Select the PSR1212 Unit and Input Channel you want to use To compare site files Document Compare UtilityTo use tone Open window Operation ~ Utilities Print Preview window Copying settings Print Reports window Print Reports GFirm Firmware Utility To upgrade firmwareToolbar Button 13. Selecting baud rate To use G-Ware Switcher Ware SwitcherCopy and paste settings Monitoring Views Message LogGate View Operation ~ Monitoring Views Meter Views To configure Meter Views Control/Status a To program control/status pinsGpio Builder Control ~ Remote Builder Remote BuilderXAP IR Remote Control ~ Remote Builder To program the XAP IR Remote Select IR Remote default from the Select Remote Type listClearOne Control Panels Control ~ Remote Builder To program the Volume panel Select Panel selected in the Remote Builder To program the Select panel RS-232 Port Remote Modem AccessSerial commands To create a command string Command stringsTo run a command string Control ~ RS-232 Port Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Appendix B Pinouts All nine pins be connected toPin Number Pin Number Control Pin Definable Type Default Description Control/Status connectorsFirst 16 pins on Appendices ~ Appendix B Pinouts +5VDC, 300mA Preset select bitControl/Status B port pinout Set connector pinout RS-485 Remote Panel a and B connectorsLine connector pinout Pin Description Appendix C Control Panel Connecting the Control Panel 800 ft/244 m Appendices ~ Appendix C Control Panel Figure C.6. Volume Control Panel Assembly Accessory ClearOne Part Number Appendix D AccessoriesAppendices ~ Appendix D Accessories Command structure Appendix E Serial CommandsConventions Example Groups and channels Appendices ~ Appendix E Serial CommandsType and device IDs Unit type Meter type definitions Serial command error codesError number Text message Explanation/Solution Command Function PSR1212 Serial commands Selects/reports off attenuation mode for Selects/reports NOM setting on outputSelects/reports signal generator activation Channels Amblvl Ambient Level Adjust Aamb Adaptive Ambient ModeAGC Automatic Gain Control Argument details Cgroup Compressor Group Select Chairo Chairman Override ModeBaud Baud Rate Gain of 3dB Compress Compressor AdjustCompsel Compression Select Delay Delay Adjust Decay Decay AdjustDelaysel Delay Select 100 101 Dfltm Default MeterDid Device ID Channel Group 102 Filter Filter AdjustExamples Name Description Units 103 FMP First Mic Priority ModeFiltsel Filter Select Flow Flow Control 104 Gain Gain AdjustmentFPP Front Panel Passcode Button assignment 105 GHOLD- Gate Hold Time AdjustGate Gate Status Example Gratio Gate Ratio Adjust Gmode Gating Mode106 Gover Gating Override Grpsel Gating Group Select Greport Gate ReportLabel Label 107 Lock Preset and Macro Lock LMO Last Mic On Mode108 LFP Lock Front Panel Lockpwd Set preset/macro password Lockprst Apply the lock to a preset or macro109 LVL Level Lvlreport Level Report 110Lvlrrate Level Report Rate = Toggle MAX Maximum Gain Setting Master Expansion Bus Master ModeThis setting will affect all relative gain adjustments Macro Macro Execution/Reporting 112 Mdmode Modem ModeMIN Minimum Gain Setting Minit Modem Initialization String Minmax Minimum and Maximum Gain Setting113 Mpass Modem Password Mline Mic/Line Adjust114 Mmax Maximum Number of Microphones Mtrx Matrix Mtrxlvl Matrix Attenuation Adjustment115 Offa Off Attenuation Mode NOM Number of Open Microphones Mode116 Mute Mute PP Phantom Power PAA PA Adaptive ModePreset Preset Execution/Reporting 117 Prgstring Program String 118Supported special characters String location 119 Ramp Ramp Gain AdjustmentRefsel PA/AEC Reference Select Name Description Unit Sermode Serial Mode Refset Reference channel setup120 Serecho Serial Echo 121 Sftymute Safety muteSiggen Signal Generator 122 Sigtout Signal Generator Time OutString String Execution Tout Time Out Select 123 Command Value Null to return valueUID Unit ID VER Version 124 Appendix F Warranty 125 Appendices ~ Appendix F Warranty 126 Safety InformationAppendix G Compliance FCC Part 15 Compliance Glossary 127 Glossary 128 129 130 131 132 133 134 Signal Delay Used for 135 Index 136 Index 137 Frequency response Phase138 139