Manuals / ClearOne comm / Musical Instruments & Equipment / Music Mixer

ClearOne comm PSR1212 operation manual 130

Models: PSR1212

1 145

Download 145 pages 59.91 Kb

Page 136

130

Glossary

the designated frequency occurs at a fixed 6dB/octave rate. The gain or loss below the corner frequency is adjustable to +/- 15dB.

Filter Display A group of nodes plotted on a logarithmic scale. The

PSR1212’s filter display can be accessed through the Inputs 1-8, From Processing, or To Processing windows.

First Mic Priority Increases the audio level required to gate on additional microphones after the first mic is on. This helps ensure that only one mic gates on when a person speaks.

Flow control The regulation of the transmission and reception of data.

Flow Screen The Flow Screen is the main access window for G-Ware features and unit configuration. It also shows a detailed block diagram of the audio signal— presenting a graphical explanation of each stage in the signal path.

Gain The amount a signal is increased over a given reference, typically 0. Normally specified in dB (decibels). On the PSR1212, gain is adjustable from -65 to 20dB (85dB range) in .5dB increments.

Gain Structure The configuration of parameters which define gain adjustment of a signal. The optimal input gain setting is one which provides both an adequate signal- to-noise ratio and reasonable headroom.

Gate The activation and deactivation of microphones.

•Auto The microphone will gate on according to the input level, assigned gating parameters, and gating group.

•Manual On The microphone will gate on unless it exceeds the NOM requirements of the gating group.

•Manual Off The microphone is deactivated.

Gate Ratio Specifies how much louder the microphone audio level must be above the ambient sound level before a microphone gates on.

Gating controls The gating parameters that are assigned to a gating group: Maximum Number of Mics, First Mic Priority, and Last Mic Mode.

Gating groups A set of gating parameters which can be applied to local microphones (Internal 1–4) or to microphones connected to other units on the network (Global A–D). Gating groups provide greater flexibility and control of mics.

Global gating bus Part of the expansion bus, these four mix-minus buses pass mic status and gate parameter information such as First Mic Priority and Max NOM.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 136

ClearOne comm PSR1212 operation manual 130

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No June 2002 Rev Table of Contents Advanced Configuration System ConfigurationControl AppendicesTechnical Services Group ~ 1-800-283-5936 USA ~ Introduction Product overviewNew Features Professional Services Group Sales and Customer ServiceTechnical Support ClearOne Communications EuMEA GmbHControls and Connections UnpackingFront panel Rear panel Introduction ~ Controls and ConnectionsIntroduction ~ Controls and Connections Networking Expansion busPower Equipment placementOperational Requirements EnvironmentalInstallation Hardware SetupInstallation ~ Hardware Setup To connect the unitInstallation ~ Networking Units Networking UnitsExpansion bus connections To create an expansion bus networkMixer mode To select a mixer modeDevice IDs To assign device IDsInstallation ~ LCD Programming LCD ProgrammingLCD menu tree Pressing Esc at the top of the tree does nothingTo adjust a parameter Select PresetSystem menu Run MacroRS-232 menu Enable Modem Clear PasswordMeter menu Flow Control hardwareInputs menu Outputs menu GainReference Point Control LogicTechnical Services Group ~ 1-800-283-5936 USA ~ System Configuration Ware RequirementsTo install G-Ware Installing G-WareCreating Floppy Disk Copies Creating a new site Site SetupTo create a new site Adding a PSR1212 To auto-detect unitsTo manually add units Select the PSR1212 icon and click AddConfiguring Unit Properties To configure Unit PropertiesSystem Configuration ~ Site Setup Ware Screens System Configuration ~ G-Ware ScreensFlow Screen Safety Mute Copying and pasting settingsStatus bar Matrix Screen 20. G-Ware Matrix ScreenAudio Routing Expansion bus O-Z routingProcess A-H routing Cross point attenuationSystem Configuration ~ Audio Routing Matrix reportInputs and Outputs InputsPwr Phantom Power FiltersActive Filter TypeTable View To configure filters GateActivation NOM count Manual Off deactivates the micPA Adaptive Mode Chairman OverrideAdaptive Ambient Gate RatioDecay Rate PA Adapt and AEC ReferenceTo create a virtual reference Click Close to exit the windowGating Group Select To configure gating group settingsTo assign a gating group Click the Gating Group label to change the group names Min/Max limitsMeters 38. Inputs 9-12 Configuration window 40. Gain meters Outputs NOMOptimizing output gain structure From Expansion Bus O-Z Expansion BusesTo Expansion Bus O-Z Processing Processing A-HCmprs compressor Group47. Processing Filters window Phase BypassAdd Filter Remove FilterDelay Changes you make in the distance and temperature fields50. Process Gain adjust and meter Optimizing process gain structureCreating Presets PresetsOverview Affected when the preset is run Preset Configuration panePreset password is set in the Unit Properties window see Advanced Configuration ~ Presets Assigning virtual references to the preset To create a preset Storage spaceRunning presets Running multiple presets simultaneouslyTo run a preset using G-Ware To run a preset using front panel controlAll presets are ready to run again Room combining exampleFour macros one for each configuration are set up as follows Macros To create a macro using Macro RecorderCreating macros To create a macro using Macro Editor 16 Macro Name windowTo add or insert a command line Editing macrosTo edit a macro To delete a macroTo run a macro using G-Ware To run a macro using front panel controlTo run a macro using the Select panel or Gpio Running macrosSignal Generator UtilitiesTo use pink or white noise Select the PSR1212 Unit and Input Channel you want to useTo use tone Document Compare UtilityTo compare site files Operation ~ Utilities Open windowCopying settings Print Preview windowPrint Reports Print Reports windowGFirm Firmware Utility To upgrade firmwareToolbar 13. Selecting baud rate Copy and paste settings Ware SwitcherTo use G-Ware Switcher Message Log Monitoring ViewsGate View Operation ~ Monitoring ViewsTo configure Meter Views Meter ViewsGpio Builder To program control/status pinsControl/Status a XAP IR Remote Remote BuilderControl ~ Remote Builder ClearOne Control Panels Select IR Remote default from the Select Remote Type listControl ~ Remote Builder To program the XAP IR Remote To program the Volume panel Control ~ Remote BuilderTo program the Select panel Select Panel selected in the Remote BuilderSerial commands Remote Modem AccessRS-232 Port Command strings To create a command stringTo run a command string Control ~ RS-232 PortTechnical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications All nine pins be connected to Appendix B PinoutsPin Number Pin Number ControlControl/Status connectors Pin Definable Type Default DescriptionFirst 16 pins on Appendices ~ Appendix B PinoutsControl/Status B port pinout Preset select bit+5VDC, 300mA RS-485 Remote Panel a and B connectors Set connector pinoutLine connector pinout Pin DescriptionConnecting the Control Panel Appendix C Control PanelAppendices ~ Appendix C Control Panel 800 ft/244 mVolume Control Panel Appendices ~ Appendix D Accessories Appendix D AccessoriesAccessory ClearOne Part Number Appendix E Serial Commands Command structureConventions ExampleAppendices ~ Appendix E Serial Commands Groups and channelsType and device IDs Unit typeError number Text message Explanation/Solution Serial command error codesMeter type definitions PSR1212 Serial commands Command FunctionSelects/reports NOM setting on output Selects/reports off attenuation mode forSelects/reports signal generator activation ChannelsAamb Adaptive Ambient Mode Amblvl Ambient Level AdjustAGC Automatic Gain Control Argument detailsBaud Baud Rate Chairo Chairman Override ModeCgroup Compressor Group Select Compsel Compression Select Compress Compressor AdjustGain of 3dB Decay Decay Adjust Delay Delay AdjustDelaysel Delay Select 100Dfltm Default Meter 101Did Device ID Channel GroupFilter Filter Adjust 102Examples Name Description UnitsFMP First Mic Priority Mode 103Filtsel Filter Select Flow Flow ControlGain Gain Adjustment 104FPP Front Panel Passcode Button assignmentGHOLD- Gate Hold Time Adjust 105Gate Gate Status ExampleGmode Gating Mode Gratio Gate Ratio Adjust106 Gover Gating OverrideGreport Gate Report Grpsel Gating Group SelectLabel Label 107LMO Last Mic On Mode Lock Preset and Macro Lock108 LFP Lock Front PanelLockprst Apply the lock to a preset or macro Lockpwd Set preset/macro password109 LVL Level110 Lvlreport Level ReportLvlrrate Level Report Rate = ToggleMaster Expansion Bus Master Mode MAX Maximum Gain SettingThis setting will affect all relative gain adjustments Macro Macro Execution/ReportingMIN Minimum Gain Setting Mdmode Modem Mode112 113 Minmax Minimum and Maximum Gain SettingMinit Modem Initialization String Mline Mic/Line Adjust Mpass Modem Password114 Mmax Maximum Number of Microphones115 Mtrxlvl Matrix Attenuation AdjustmentMtrx Matrix NOM Number of Open Microphones Mode Offa Off Attenuation Mode116 Mute MutePAA PA Adaptive Mode PP Phantom PowerPreset Preset Execution/Reporting 117118 Prgstring Program StringSupported special characters String locationRamp Ramp Gain Adjustment 119Refsel PA/AEC Reference Select Name Description UnitRefset Reference channel setup Sermode Serial Mode120 Serecho Serial EchoSiggen Signal Generator Sftymute Safety mute121 Sigtout Signal Generator Time Out 122String String Execution Tout Time Out SelectCommand Value Null to return value 123UID Unit ID VER VersionAppendix F Warranty 124Appendices ~ Appendix F Warranty 125Safety Information 126Appendix G Compliance FCC Part 15 Compliance127 Glossary128 Glossary129 130 131 132 133 Signal Delay Used for 134135 136 Index137 Index138 PhaseFrequency response 139