Copying and pasting settings, Safety Mute | ClearOne comm PSR1212

28	System Configuration ~ G-Ware Screens

Figure 3.17. Unit shortcut menu

Figure 3.18. Inputs 1–8 shortcut menu

Figure 3.19.

Safety Mute

Copying and pasting settings

G-Ware has shortcut menus which appear when you right-click a selection or program window in G-Ware. These shortcut menus provide quick access to options such as Print, Copy, and Paste that pertain only to that selection or screen region. Using the Copy and Paste commands, you can copy and paste unit data such as a single setting or the entire unit’s settings depending on which window you are in. For example, if you are in the Inputs 1–8 window, using the shortcut menu will allow you to copy and paste all of the input settings to other inputs. You can also use keyboard shortcuts (Ctrl+C and Ctrl+V) to copy and paste settings. If you want to apply all settings of a selected input to the rest of the inputs, select Apply to All.

Safety Mute

The Safety Mute feature in G-Ware enables you to mute all outputs if feedback or audio problems occur during the configuration process. To use Safety Mute, click the Safety Mute button on the G-Ware toolbar. Then find and correct the cause of the problem. Click the Safety Mute button again to unmute the outputs.

Status bar

There are two status lights at the bottom of the G-Ware window representing the unit and the site. The lights illuminate in various colors to indicate current status.

•Solid green. The item being configured is synchronized with the hardware.

•Solid red. The information being configured is saved in the software offline.

•Flashing red. The information is not saved or there is no hardware connection.

•Solid yellow. Communications are pending.

•Flashing yellow. There is a communication error. In this instance, you should disconnect from the unit and reconnect. The Message Log will indicate the error that occurred. See page 73 for more information.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 34

ClearOne comm PSR1212 operation manual Copying and pasting settings, Safety Mute, Status bar

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No June 2002 Rev Table of Contents Advanced Configuration System Configuration Control Appendices Technical Services Group ~ 1-800-283-5936 USA ~ Introduction Product overview New Features Technical Support Professional Services GroupSales and Customer Service ClearOne Communications EuMEA GmbH Controls and Connections UnpackingFront panel Rear panel Introduction ~ Controls and Connections Introduction ~ Controls and Connections Networking Expansion bus Operational Requirements PowerEquipment placement Environmental Installation Hardware Setup Installation ~ Hardware Setup To connect the unit Expansion bus connections Installation ~ Networking UnitsNetworking Units To create an expansion bus network Device IDs Mixer modeTo select a mixer mode To assign device IDs LCD menu tree Installation ~ LCD ProgrammingLCD Programming Pressing Esc at the top of the tree does nothing System menu To adjust a parameterSelect Preset Run Macro RS-232 menu Meter menu Enable ModemClear Password Flow Control hardware Inputs menu Outputs menu Gain Matrix Technical Services Group ~ 1-800-283-5936 USA ~ System Configuration Ware Requirements To install G-Ware Installing G-WareCreating Floppy Disk Copies Creating a new site Site SetupTo create a new site To manually add units Adding a PSR1212To auto-detect units Select the PSR1212 icon and click Add Configuring Unit Properties To configure Unit Properties System Configuration ~ Site Setup Ware Screens System Configuration ~ G-Ware ScreensFlow Screen Safety Mute Copying and pasting settingsStatus bar Matrix Screen 20. G-Ware Matrix Screen Process A-H routing Audio RoutingExpansion bus O-Z routing Cross point attenuation System Configuration ~ Audio Routing Matrix report Inputs and Outputs Inputs Active Filter Pwr Phantom PowerFilters Type Table View Activation To configure filtersGate NOM count Manual Off deactivates the mic Adaptive Ambient PA Adaptive ModeChairman Override Gate Ratio Decay Rate PA Adapt and AEC Reference To create a virtual reference Click Close to exit the window Gating Group Select To configure gating group settingsTo assign a gating group Click the Gating Group label to change the group names Min/Max limits Meters 38. Inputs 9-12 Configuration window 40. Gain meters Outputs NOM Optimizing output gain structure From Expansion Bus O-Z Expansion BusesTo Expansion Bus O-Z Processing Processing A-H Compressors Cmprs compressorGroup 47. Processing Filters window Add Filter PhaseBypass Remove Filter Delay Changes you make in the distance and temperature fields 50. Process Gain adjust and meter Optimizing process gain structure Creating Presets PresetsOverview Affected when the preset is run Preset Configuration panePreset password is set in the Unit Properties window see Advanced Configuration ~ Presets Assigning virtual references to the preset To create a preset Storage space To run a preset using G-Ware Running presetsRunning multiple presets simultaneously To run a preset using front panel control All presets are ready to run again Room combining example Four macros one for each configuration are set up as follows Macros To create a macro using Macro RecorderCreating macros To create a macro using Macro Editor 16 Macro Name window To edit a macro To add or insert a command lineEditing macros To delete a macro To run a macro using the Select panel or Gpio To run a macro using G-WareTo run a macro using front panel control Running macros To use pink or white noise Signal GeneratorUtilities Select the PSR1212 Unit and Input Channel you want to use To use tone Document Compare UtilityTo compare site files Operation ~ Utilities Open window Copying settings Print Preview window Print Reports Print Reports window Toolbar To upgrade firmwareGFirm Firmware Utility Button 13. Selecting baud rate Copy and paste settings Ware SwitcherTo use G-Ware Switcher Gate View Message LogMonitoring Views Operation ~ Monitoring Views To configure Meter Views Meter Views Gpio Builder To program control/status pinsControl/Status a XAP IR Remote Remote BuilderControl ~ Remote Builder ClearOne Control Panels Select IR Remote default from the Select Remote Type listControl ~ Remote Builder To program the XAP IR Remote To program the Volume panel Control ~ Remote Builder To program the Select panel Select Panel selected in the Remote Builder Serial commands Remote Modem AccessRS-232 Port To run a command string Command stringsTo create a command string Control ~ RS-232 Port Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Pin Number All nine pins be connected toAppendix B Pinouts Pin Number Control First 16 pins on Control/Status connectorsPin Definable Type Default Description Appendices ~ Appendix B Pinouts Control/Status B port pinout Preset select bit+5VDC, 300mA Line connector pinout RS-485 Remote Panel a and B connectorsSet connector pinout Pin Description Connecting the Control Panel Appendix C Control Panel Appendices ~ Appendix C Control Panel 800 ft/244 m Figure C.6. Volume Control Panel Assembly Appendices ~ Appendix D Accessories Appendix D AccessoriesAccessory ClearOne Part Number Conventions Appendix E Serial CommandsCommand structure Example Type and device IDs Appendices ~ Appendix E Serial CommandsGroups and channels Unit type Error number Text message Explanation/Solution Serial command error codesMeter type definitions PSR1212 Serial commands Command Function Selects/reports signal generator activation Selects/reports NOM setting on outputSelects/reports off attenuation mode for Channels AGC Automatic Gain Control Aamb Adaptive Ambient ModeAmblvl Ambient Level Adjust Argument details Baud Baud Rate Chairo Chairman Override ModeCgroup Compressor Group Select Compsel Compression Select Compress Compressor AdjustGain of 3dB Delaysel Delay Select Decay Decay AdjustDelay Delay Adjust 100 Did Device ID Dfltm Default Meter101 Channel Group Examples Filter Filter Adjust102 Name Description Units Filtsel Filter Select FMP First Mic Priority Mode103 Flow Flow Control FPP Front Panel Passcode Gain Gain Adjustment104 Button assignment Gate Gate Status GHOLD- Gate Hold Time Adjust105 Example 106 Gmode Gating ModeGratio Gate Ratio Adjust Gover Gating Override Label Label Greport Gate ReportGrpsel Gating Group Select 107 108 LMO Last Mic On ModeLock Preset and Macro Lock LFP Lock Front Panel 109 Lockprst Apply the lock to a preset or macroLockpwd Set preset/macro password LVL Level Lvlrrate Level Report Rate 110Lvlreport Level Report = Toggle This setting will affect all relative gain adjustments Master Expansion Bus Master ModeMAX Maximum Gain Setting Macro Macro Execution/Reporting MIN Minimum Gain Setting Mdmode Modem Mode112 113 Minmax Minimum and Maximum Gain SettingMinit Modem Initialization String 114 Mline Mic/Line AdjustMpass Modem Password Mmax Maximum Number of Microphones 115 Mtrxlvl Matrix Attenuation AdjustmentMtrx Matrix 116 NOM Number of Open Microphones ModeOffa Off Attenuation Mode Mute Mute Preset Preset Execution/Reporting PAA PA Adaptive ModePP Phantom Power 117 Supported special characters 118Prgstring Program String String location Refsel PA/AEC Reference Select Ramp Ramp Gain Adjustment119 Name Description Unit 120 Refset Reference channel setupSermode Serial Mode Serecho Serial Echo Siggen Signal Generator Sftymute Safety mute121 String String Execution Sigtout Signal Generator Time Out122 Tout Time Out Select UID Unit ID Command Value Null to return value123 VER Version Appendix F Warranty 124 Appendices ~ Appendix F Warranty 125 Appendix G Compliance Safety Information126 FCC Part 15 Compliance 127 Glossary 128 Glossary 129 130 131 132 133 Signal Delay Used for 134 135 136 Index 137 Index 138 PhaseFrequency response 139