113, Minit Modem Initialization String | ClearOne comm PSR1212

Appendices ~ Appendix E: Serial Commands

113

MINIT - Modem Initialization String

This command sets/reports the modem initialization string of the serial port when in modem mode.

Command form: DEVICE MINIT [String]

Argument details

Name	Description
Device	0–7 or * to select all units
MINIT	Command form
String	1-80 characters (select string characters to be sent to the modem
	when the unit is initialized
	CLEAR = clears the modem initialization string
	Null = Current string

Example: #46 MINIT ATZ On PSR1212 unit 6 (#46), the modem initialization

string (MINIT) is ATZ.

MINMAX - Minimum and Maximum Gain Setting

This command changes or reports back the minimum and maximum gain setting for an input, output or assignable processing block.

Command form: DEVICE MINMAX <Channel> <Group> [Minimum] [Maximum]

Argument details

Name	Description
Device	0–7 or * to select all units
MINMAX	Command form
Channel	See Groups and Channels
Group	I, O, M, P, L
Minimum	-65.00 to 20.00, Null to return current settings
Maximum	-65.00 – 20.00

Example: #45 MINMAX 2 M -12 10 On PSR1212 unit 5 (#45), the minimum and maximum (MINMAX) relative gain settings for mic (M) channel 2 are -12dB

and 10dB respectively.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 119

ClearOne comm PSR1212 operation manual 113, Minit Modem Initialization String, Minmax Minimum and Maximum Gain Setting

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No June 2002 Rev Table of Contents System Configuration Advanced Configuration Appendices Control Technical Services Group ~ 1-800-283-5936 USA ~ Product overview Introduction New Features ClearOne Communications EuMEA GmbH Professional Services GroupSales and Customer Service Technical Support Front panel UnpackingControls and Connections Introduction ~ Controls and Connections Rear panel Introduction ~ Controls and Connections Expansion bus Networking Environmental PowerEquipment placement Operational Requirements Hardware Setup Installation To connect the unit Installation ~ Hardware Setup To create an expansion bus network Installation ~ Networking UnitsNetworking Units Expansion bus connections To assign device IDs Mixer modeTo select a mixer mode Device IDs Pressing Esc at the top of the tree does nothing Installation ~ LCD ProgrammingLCD Programming LCD menu tree Run Macro To adjust a parameterSelect Preset System menu RS-232 menu Flow Control hardware Enable ModemClear Password Meter menu Inputs menu Gain Outputs menu Matrix Technical Services Group ~ 1-800-283-5936 USA ~ Ware Requirements System Configuration Creating Floppy Disk Copies Installing G-WareTo install G-Ware To create a new site Site SetupCreating a new site Select the PSR1212 icon and click Add Adding a PSR1212To auto-detect units To manually add units To configure Unit Properties Configuring Unit Properties System Configuration ~ Site Setup Flow Screen System Configuration ~ G-Ware ScreensWare Screens Status bar Copying and pasting settingsSafety Mute 20. G-Ware Matrix Screen Matrix Screen Cross point attenuation Audio RoutingExpansion bus O-Z routing Process A-H routing Matrix report System Configuration ~ Audio Routing Inputs Inputs and Outputs Type Pwr Phantom PowerFilters Active Filter Table View NOM count Manual Off deactivates the mic To configure filtersGate Activation Gate Ratio PA Adaptive ModeChairman Override Adaptive Ambient PA Adapt and AEC Reference Decay Rate Click Close to exit the window To create a virtual reference To assign a gating group To configure gating group settingsGating Group Select Min/Max limits Click the Gating Group label to change the group names Meters 38. Inputs 9-12 Configuration window 40. Gain meters NOM Outputs Optimizing output gain structure To Expansion Bus O-Z Expansion BusesFrom Expansion Bus O-Z Processing A-H Processing Group Cmprs compressorCompressors 47. Processing Filters window Remove Filter PhaseBypass Add Filter Changes you make in the distance and temperature fields Delay Optimizing process gain structure 50. Process Gain adjust and meter Overview PresetsCreating Presets Preset password is set in the Unit Properties window see Preset Configuration paneAffected when the preset is run Advanced Configuration ~ Presets Assigning virtual references to the preset Storage space To create a preset To run a preset using front panel control Running presetsRunning multiple presets simultaneously To run a preset using G-Ware Room combining example All presets are ready to run again Four macros one for each configuration are set up as follows Creating macros To create a macro using Macro RecorderMacros 16 Macro Name window To create a macro using Macro Editor To delete a macro To add or insert a command lineEditing macros To edit a macro Running macros To run a macro using G-WareTo run a macro using front panel control To run a macro using the Select panel or Gpio Select the PSR1212 Unit and Input Channel you want to use Signal GeneratorUtilities To use pink or white noise To compare site files Document Compare UtilityTo use tone Open window Operation ~ Utilities Print Preview window Copying settings Print Reports window Print Reports Button To upgrade firmwareGFirm Firmware Utility Toolbar 13. Selecting baud rate To use G-Ware Switcher Ware SwitcherCopy and paste settings Operation ~ Monitoring Views Message LogMonitoring Views Gate View Meter Views To configure Meter Views Control/Status a To program control/status pinsGpio Builder Control ~ Remote Builder Remote BuilderXAP IR Remote Control ~ Remote Builder To program the XAP IR Remote Select IR Remote default from the Select Remote Type listClearOne Control Panels Control ~ Remote Builder To program the Volume panel Select Panel selected in the Remote Builder To program the Select panel RS-232 Port Remote Modem AccessSerial commands Control ~ RS-232 Port Command stringsTo create a command string To run a command string Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Pin Number Control All nine pins be connected toAppendix B Pinouts Pin Number Appendices ~ Appendix B Pinouts Control/Status connectorsPin Definable Type Default Description First 16 pins on +5VDC, 300mA Preset select bitControl/Status B port pinout Pin Description RS-485 Remote Panel a and B connectorsSet connector pinout Line connector pinout Appendix C Control Panel Connecting the Control Panel 800 ft/244 m Appendices ~ Appendix C Control Panel Figure C.6. Volume Control Panel Assembly Accessory ClearOne Part Number Appendix D AccessoriesAppendices ~ Appendix D Accessories Example Appendix E Serial CommandsCommand structure Conventions Unit type Appendices ~ Appendix E Serial CommandsGroups and channels Type and device IDs Meter type definitions Serial command error codesError number Text message Explanation/Solution Command Function PSR1212 Serial commands Channels Selects/reports NOM setting on outputSelects/reports off attenuation mode for Selects/reports signal generator activation Argument details Aamb Adaptive Ambient ModeAmblvl Ambient Level Adjust AGC Automatic Gain Control Cgroup Compressor Group Select Chairo Chairman Override ModeBaud Baud Rate Gain of 3dB Compress Compressor AdjustCompsel Compression Select 100 Decay Decay AdjustDelay Delay Adjust Delaysel Delay Select Channel Group Dfltm Default Meter101 Did Device ID Name Description Units Filter Filter Adjust102 Examples Flow Flow Control FMP First Mic Priority Mode103 Filtsel Filter Select Button assignment Gain Gain Adjustment104 FPP Front Panel Passcode Example GHOLD- Gate Hold Time Adjust105 Gate Gate Status Gover Gating Override Gmode Gating ModeGratio Gate Ratio Adjust 106 107 Greport Gate ReportGrpsel Gating Group Select Label Label LFP Lock Front Panel LMO Last Mic On ModeLock Preset and Macro Lock 108 LVL Level Lockprst Apply the lock to a preset or macroLockpwd Set preset/macro password 109 = Toggle 110Lvlreport Level Report Lvlrrate Level Report Rate Macro Macro Execution/Reporting Master Expansion Bus Master ModeMAX Maximum Gain Setting This setting will affect all relative gain adjustments 112 Mdmode Modem ModeMIN Minimum Gain Setting Minit Modem Initialization String Minmax Minimum and Maximum Gain Setting113 Mmax Maximum Number of Microphones Mline Mic/Line AdjustMpass Modem Password 114 Mtrx Matrix Mtrxlvl Matrix Attenuation Adjustment115 Mute Mute NOM Number of Open Microphones ModeOffa Off Attenuation Mode 116 117 PAA PA Adaptive ModePP Phantom Power Preset Preset Execution/Reporting String location 118Prgstring Program String Supported special characters Name Description Unit Ramp Ramp Gain Adjustment119 Refsel PA/AEC Reference Select Serecho Serial Echo Refset Reference channel setupSermode Serial Mode 120 121 Sftymute Safety muteSiggen Signal Generator Tout Time Out Select Sigtout Signal Generator Time Out122 String String Execution VER Version Command Value Null to return value123 UID Unit ID 124 Appendix F Warranty 125 Appendices ~ Appendix F Warranty FCC Part 15 Compliance Safety Information126 Appendix G Compliance Glossary 127 Glossary 128 129 130 131 132 133 134 Signal Delay Used for 135 Index 136 Index 137 Frequency response Phase138 139