Meter type definitions | ClearOne comm PSR1212 manual

94

Meter type definitions

Appendices ~ Appendix E: Serial Commands

Serial command error codes

Error number	Text message	Explanation/Solution
1	Memory error	The box is out of internal memory. Power cycle the box.
2	No command found	A command was not found in the string.
3	Unknown command	A command was executed on a different device type that this box
	response	cannot display. The command dictionary needs to be updated.
4	Not implemented	The command is not implemented.
5	Argument error	The command had an argument that was out of range.
6	Unknown command	The command is unknown to this unit.
7	Bad checksum	The binary command’s checksum is wrong.
8	Preset of macro invalid	A preset or macro failed to program because it is too large or
		because its command list contained an invalid command.
10	Queue error	The internal command queue is full. Enable flow control and use
		all five pins on the serial port.
11	Command too big	The binary command is too large.
12	Unit is locked	Unlock the unit with the proper password.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 100

ClearOne comm PSR1212 Meter type definitions, Serial command error codes, Error number Text message Explanation/Solution

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No June 2002 Rev Table of Contents Advanced Configuration System Configuration Control Appendices Technical Services Group ~ 1-800-283-5936 USA ~ Introduction Product overview New Features Professional Services Group Sales and Customer ServiceTechnical Support ClearOne Communications EuMEA GmbH Controls and Connections UnpackingFront panel Rear panel Introduction ~ Controls and Connections Introduction ~ Controls and Connections Networking Expansion bus Power Equipment placementOperational Requirements Environmental Installation Hardware Setup Installation ~ Hardware Setup To connect the unit Installation ~ Networking Units Networking UnitsExpansion bus connections To create an expansion bus network Mixer mode To select a mixer modeDevice IDs To assign device IDs Installation ~ LCD Programming LCD ProgrammingLCD menu tree Pressing Esc at the top of the tree does nothing To adjust a parameter Select PresetSystem menu Run Macro RS-232 menu Enable Modem Clear PasswordMeter menu Flow Control hardware Inputs menu Outputs menu Gain Matrix Technical Services Group ~ 1-800-283-5936 USA ~ System Configuration Ware Requirements To install G-Ware Installing G-WareCreating Floppy Disk Copies Creating a new site Site SetupTo create a new site Adding a PSR1212 To auto-detect unitsTo manually add units Select the PSR1212 icon and click Add Configuring Unit Properties To configure Unit Properties System Configuration ~ Site Setup Ware Screens System Configuration ~ G-Ware ScreensFlow Screen Safety Mute Copying and pasting settingsStatus bar Matrix Screen 20. G-Ware Matrix Screen Audio Routing Expansion bus O-Z routingProcess A-H routing Cross point attenuation System Configuration ~ Audio Routing Matrix report Inputs and Outputs Inputs Pwr Phantom Power FiltersActive Filter Type Table View To configure filters GateActivation NOM count Manual Off deactivates the mic PA Adaptive Mode Chairman OverrideAdaptive Ambient Gate Ratio Decay Rate PA Adapt and AEC Reference To create a virtual reference Click Close to exit the window Gating Group Select To configure gating group settingsTo assign a gating group Click the Gating Group label to change the group names Min/Max limits Meters 38. Inputs 9-12 Configuration window 40. Gain meters Outputs NOM Optimizing output gain structure From Expansion Bus O-Z Expansion BusesTo Expansion Bus O-Z Processing Processing A-H Compressors Cmprs compressorGroup 47. Processing Filters window Phase BypassAdd Filter Remove Filter Delay Changes you make in the distance and temperature fields 50. Process Gain adjust and meter Optimizing process gain structure Creating Presets PresetsOverview Affected when the preset is run Preset Configuration panePreset password is set in the Unit Properties window see Advanced Configuration ~ Presets Assigning virtual references to the preset To create a preset Storage space Running presets Running multiple presets simultaneouslyTo run a preset using G-Ware To run a preset using front panel control All presets are ready to run again Room combining example Four macros one for each configuration are set up as follows Macros To create a macro using Macro RecorderCreating macros To create a macro using Macro Editor 16 Macro Name window To add or insert a command line Editing macrosTo edit a macro To delete a macro To run a macro using G-Ware To run a macro using front panel controlTo run a macro using the Select panel or Gpio Running macros Signal Generator UtilitiesTo use pink or white noise Select the PSR1212 Unit and Input Channel you want to use To use tone Document Compare UtilityTo compare site files Operation ~ Utilities Open window Copying settings Print Preview window Print Reports Print Reports window To upgrade firmware GFirm Firmware UtilityToolbar Button 13. Selecting baud rate Copy and paste settings Ware SwitcherTo use G-Ware Switcher Message Log Monitoring ViewsGate View Operation ~ Monitoring Views To configure Meter Views Meter Views Gpio Builder To program control/status pinsControl/Status a XAP IR Remote Remote BuilderControl ~ Remote Builder ClearOne Control Panels Select IR Remote default from the Select Remote Type listControl ~ Remote Builder To program the XAP IR Remote To program the Volume panel Control ~ Remote Builder To program the Select panel Select Panel selected in the Remote Builder Serial commands Remote Modem AccessRS-232 Port Command strings To create a command stringTo run a command string Control ~ RS-232 Port Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications All nine pins be connected to Appendix B PinoutsPin Number Pin Number Control Control/Status connectors Pin Definable Type Default DescriptionFirst 16 pins on Appendices ~ Appendix B Pinouts Control/Status B port pinout Preset select bit+5VDC, 300mA RS-485 Remote Panel a and B connectors Set connector pinoutLine connector pinout Pin Description Connecting the Control Panel Appendix C Control Panel Appendices ~ Appendix C Control Panel 800 ft/244 m Figure C.6. Volume Control Panel Assembly Appendices ~ Appendix D Accessories Appendix D AccessoriesAccessory ClearOne Part Number Appendix E Serial Commands Command structureConventions Example Appendices ~ Appendix E Serial Commands Groups and channelsType and device IDs Unit type Error number Text message Explanation/Solution Serial command error codesMeter type definitions PSR1212 Serial commands Command Function Selects/reports NOM setting on output Selects/reports off attenuation mode forSelects/reports signal generator activation Channels Aamb Adaptive Ambient Mode Amblvl Ambient Level AdjustAGC Automatic Gain Control Argument details Baud Baud Rate Chairo Chairman Override ModeCgroup Compressor Group Select Compsel Compression Select Compress Compressor AdjustGain of 3dB Decay Decay Adjust Delay Delay AdjustDelaysel Delay Select 100 Dfltm Default Meter 101Did Device ID Channel Group Filter Filter Adjust 102Examples Name Description Units FMP First Mic Priority Mode 103Filtsel Filter Select Flow Flow Control Gain Gain Adjustment 104FPP Front Panel Passcode Button assignment GHOLD- Gate Hold Time Adjust 105Gate Gate Status Example Gmode Gating Mode Gratio Gate Ratio Adjust106 Gover Gating Override Greport Gate Report Grpsel Gating Group SelectLabel Label 107 LMO Last Mic On Mode Lock Preset and Macro Lock108 LFP Lock Front Panel Lockprst Apply the lock to a preset or macro Lockpwd Set preset/macro password109 LVL Level 110 Lvlreport Level ReportLvlrrate Level Report Rate = Toggle Master Expansion Bus Master Mode MAX Maximum Gain SettingThis setting will affect all relative gain adjustments Macro Macro Execution/Reporting MIN Minimum Gain Setting Mdmode Modem Mode112 113 Minmax Minimum and Maximum Gain SettingMinit Modem Initialization String Mline Mic/Line Adjust Mpass Modem Password114 Mmax Maximum Number of Microphones 115 Mtrxlvl Matrix Attenuation AdjustmentMtrx Matrix NOM Number of Open Microphones Mode Offa Off Attenuation Mode116 Mute Mute PAA PA Adaptive Mode PP Phantom PowerPreset Preset Execution/Reporting 117 118 Prgstring Program StringSupported special characters String location Ramp Ramp Gain Adjustment 119Refsel PA/AEC Reference Select Name Description Unit Refset Reference channel setup Sermode Serial Mode120 Serecho Serial Echo Siggen Signal Generator Sftymute Safety mute121 Sigtout Signal Generator Time Out 122String String Execution Tout Time Out Select Command Value Null to return value 123UID Unit ID VER Version Appendix F Warranty 124 Appendices ~ Appendix F Warranty 125 Safety Information 126Appendix G Compliance FCC Part 15 Compliance 127 Glossary 128 Glossary 129 130 131 132 133 Signal Delay Used for 134 135 136 Index 137 Index 138 PhaseFrequency response 139