RS-485 Remote Panel a and B connectors

Appendices ~ Appendix B: Pinouts

RS-485 Remote Panel A and B connectors

Pin	Description
1	+15VDC, 300mA (over-current protected)
2	Data +
3	Data –
4	Ground

Set connector pinout

	Pin	Description	Pin	Description
1		To pin 6 of SET RJ-11C	4	Tip
2		To pin 5 of SET	5	To pin 2 of LINE
3		Ring	6	To pin 1 of LINE RJ-11C

Line connector pinout

Pin	Description	Pin	Description
1	To pin 6 of LINE RJ-11C	4	Ring
2	To pin 5 of LINE	5	To pin 2 of SET
3	Tip	6	To pin 1 of SET RJ-11C

Figure B.7. RS-485 Remote Control Ports

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Page 93

Image 93

ClearOne comm PSR1212 RS-485 Remote Panel a and B connectors, Set connector pinout, Line connector pinout, Pin Description

Contents

PSR1212 Digital Matrix Mixer PSR1212 Installation ClearOne Part No June 2002 Rev Table of Contents System Configuration Advanced Configuration Appendices Control Technical Services Group ~ 1-800-283-5936 USA ~ Product overview Introduction New Features Sales and Customer Service Professional Services GroupTechnical Support ClearOne Communications EuMEA GmbH Unpacking Controls and ConnectionsFront panel Introduction ~ Controls and Connections Rear panel Introduction ~ Controls and Connections Expansion bus Networking Equipment placement PowerOperational Requirements Environmental Hardware Setup Installation To connect the unit Installation ~ Hardware Setup Networking Units Installation ~ Networking UnitsExpansion bus connections To create an expansion bus network To select a mixer mode Mixer modeDevice IDs To assign device IDs LCD Programming Installation ~ LCD ProgrammingLCD menu tree Pressing Esc at the top of the tree does nothing Select Preset To adjust a parameterSystem menu Run Macro RS-232 menu Clear Password Enable ModemMeter menu Flow Control hardware Inputs menu Gain Outputs menu Matrix Technical Services Group ~ 1-800-283-5936 USA ~ Ware Requirements System Configuration Installing G-Ware To install G-WareCreating Floppy Disk Copies Site Setup Creating a new siteTo create a new site To auto-detect units Adding a PSR1212To manually add units Select the PSR1212 icon and click Add To configure Unit Properties Configuring Unit Properties System Configuration ~ Site Setup System Configuration ~ G-Ware Screens Ware ScreensFlow Screen Copying and pasting settings Safety MuteStatus bar 20. G-Ware Matrix Screen Matrix Screen Expansion bus O-Z routing Audio RoutingProcess A-H routing Cross point attenuation Matrix report System Configuration ~ Audio Routing Inputs Inputs and Outputs Filters Pwr Phantom PowerActive Filter Type Table View Gate To configure filtersActivation NOM count Manual Off deactivates the mic Chairman Override PA Adaptive ModeAdaptive Ambient Gate Ratio PA Adapt and AEC Reference Decay Rate Click Close to exit the window To create a virtual reference To configure gating group settings Gating Group SelectTo assign a gating group Min/Max limits Click the Gating Group label to change the group names Meters 38. Inputs 9-12 Configuration window 40. Gain meters NOM Outputs Optimizing output gain structure Expansion Buses From Expansion Bus O-ZTo Expansion Bus O-Z Processing A-H Processing Cmprs compressor CompressorsGroup 47. Processing Filters window Bypass PhaseAdd Filter Remove Filter Changes you make in the distance and temperature fields Delay Optimizing process gain structure 50. Process Gain adjust and meter Presets Creating PresetsOverview Preset Configuration pane Affected when the preset is runPreset password is set in the Unit Properties window see Advanced Configuration ~ Presets Assigning virtual references to the preset Storage space To create a preset Running multiple presets simultaneously Running presetsTo run a preset using G-Ware To run a preset using front panel control Room combining example All presets are ready to run again Four macros one for each configuration are set up as follows To create a macro using Macro Recorder MacrosCreating macros 16 Macro Name window To create a macro using Macro Editor Editing macros To add or insert a command lineTo edit a macro To delete a macro To run a macro using front panel control To run a macro using G-WareTo run a macro using the Select panel or Gpio Running macros Utilities Signal GeneratorTo use pink or white noise Select the PSR1212 Unit and Input Channel you want to use Document Compare Utility To use toneTo compare site files Open window Operation ~ Utilities Print Preview window Copying settings Print Reports window Print Reports GFirm Firmware Utility To upgrade firmwareToolbar Button 13. Selecting baud rate Ware Switcher Copy and paste settingsTo use G-Ware Switcher Monitoring Views Message LogGate View Operation ~ Monitoring Views Meter Views To configure Meter Views To program control/status pins Gpio BuilderControl/Status a Remote Builder XAP IR RemoteControl ~ Remote Builder Select IR Remote default from the Select Remote Type list ClearOne Control PanelsControl ~ Remote Builder To program the XAP IR Remote Control ~ Remote Builder To program the Volume panel Select Panel selected in the Remote Builder To program the Select panel Remote Modem Access Serial commandsRS-232 Port To create a command string Command stringsTo run a command string Control ~ RS-232 Port Technical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Appendix B Pinouts All nine pins be connected toPin Number Pin Number Control Pin Definable Type Default Description Control/Status connectorsFirst 16 pins on Appendices ~ Appendix B Pinouts Preset select bit Control/Status B port pinout+5VDC, 300mA Set connector pinout RS-485 Remote Panel a and B connectorsLine connector pinout Pin Description Appendix C Control Panel Connecting the Control Panel 800 ft/244 m Appendices ~ Appendix C Control Panel Figure C.6. Volume Control Panel Assembly Appendix D Accessories Appendices ~ Appendix D AccessoriesAccessory ClearOne Part Number Command structure Appendix E Serial CommandsConventions Example Groups and channels Appendices ~ Appendix E Serial CommandsType and device IDs Unit type Serial command error codes Error number Text message Explanation/SolutionMeter type definitions Command Function PSR1212 Serial commands Selects/reports off attenuation mode for Selects/reports NOM setting on outputSelects/reports signal generator activation Channels Amblvl Ambient Level Adjust Aamb Adaptive Ambient ModeAGC Automatic Gain Control Argument details Chairo Chairman Override Mode Baud Baud RateCgroup Compressor Group Select Compress Compressor Adjust Compsel Compression SelectGain of 3dB Delay Delay Adjust Decay Decay AdjustDelaysel Delay Select 100 101 Dfltm Default MeterDid Device ID Channel Group 102 Filter Filter AdjustExamples Name Description Units 103 FMP First Mic Priority ModeFiltsel Filter Select Flow Flow Control 104 Gain Gain AdjustmentFPP Front Panel Passcode Button assignment 105 GHOLD- Gate Hold Time AdjustGate Gate Status Example Gratio Gate Ratio Adjust Gmode Gating Mode106 Gover Gating Override Grpsel Gating Group Select Greport Gate ReportLabel Label 107 Lock Preset and Macro Lock LMO Last Mic On Mode108 LFP Lock Front Panel Lockpwd Set preset/macro password Lockprst Apply the lock to a preset or macro109 LVL Level Lvlreport Level Report 110Lvlrrate Level Report Rate = Toggle MAX Maximum Gain Setting Master Expansion Bus Master ModeThis setting will affect all relative gain adjustments Macro Macro Execution/Reporting Mdmode Modem Mode MIN Minimum Gain Setting112 Minmax Minimum and Maximum Gain Setting 113Minit Modem Initialization String Mpass Modem Password Mline Mic/Line Adjust114 Mmax Maximum Number of Microphones Mtrxlvl Matrix Attenuation Adjustment 115Mtrx Matrix Offa Off Attenuation Mode NOM Number of Open Microphones Mode116 Mute Mute PP Phantom Power PAA PA Adaptive ModePreset Preset Execution/Reporting 117 Prgstring Program String 118Supported special characters String location 119 Ramp Ramp Gain AdjustmentRefsel PA/AEC Reference Select Name Description Unit Sermode Serial Mode Refset Reference channel setup120 Serecho Serial Echo Sftymute Safety mute Siggen Signal Generator121 122 Sigtout Signal Generator Time OutString String Execution Tout Time Out Select 123 Command Value Null to return valueUID Unit ID VER Version 124 Appendix F Warranty 125 Appendices ~ Appendix F Warranty 126 Safety InformationAppendix G Compliance FCC Part 15 Compliance Glossary 127 Glossary 128 129 130 131 132 133 134 Signal Delay Used for 135 Index 136 Index 137 Phase 138Frequency response 139