Fault Messages and Error Codes

D-3

 

 

Error

Advisory Message

Description

Fault

Recommended Action

Code

 

 

Classification

 

 

(Hex)

 

 

 

 

 

 

 

 

 

 

0006

MEMORY MODULE

The memory module hardware

Non-User

• Upgrade the OS to be compatible with

 

HARDWARE FAULT

faulted or the memory module is

 

 

memory module.

 

 

incompatible with OS.

 

• Obtain a new memory module.

 

 

 

 

 

0007

MEMORY MODULE

Failure during memory module

Non-User

Re-attempt the transfer. If the error persists,

 

TRANSFER ERROR

transfer.

 

replace the memory module.

 

 

 

 

 

0008

FATAL INTERNAL

An unexpected software error

Non-User

• Cycle power on your unit. Then,

 

SOFTWARE ERROR

occurred.

 

 

re-download your program and re-initialize

 

 

 

 

 

any necessary data.

 

 

 

 

• Start up your system.

 

 

 

 

• Refer to proper grounding guidelines and

 

 

 

 

 

using surge suppressors in your controller’s

 

 

 

 

 

User Manual.

 

 

 

 

• Contact your Conair Service

 

 

 

 

 

representative if the error persists.

 

 

 

 

 

0009

FATAL INTERNAL

An unexpected hardware error

Non-User

• Cycle power on your unit. Then,

 

HARDWARE ERROR

occurred.

 

 

re-download your program and re-initialize

 

 

 

 

 

any necessary data.

 

 

 

 

• Start up your system.

 

 

 

 

• Refer to proper grounding guidelines and

 

 

 

 

 

using surge suppressors in your controller’s

 

 

 

 

 

User Manual.

 

 

 

 

• Contact your Conair Service

 

 

 

 

 

representative if the error persists.

 

 

 

 

 

000A

OS MISSING OR

The operating system required for

Non-User

• Download a new OS using ControlFlash.

 

CORRUPT

the user program is corrupt or

 

•

Contact your local Rockwell Automation

 

 

missing.

 

 

representative for more information about

 

 

 

 

 

available operating systems your

 

 

 

 

 

controller.

 

 

 

 

 

 

000B

BASE HARDWARE

The base hardware faulted or is

Non-User

•

Upgrade the OS using ControlFlash.

 

FAULT

incompatible with the OS.

 

•

Replace the Controller (MicroLogix 1200

 

 

 

 

 

only).

 

 

 

 

• Replace the Base Unit (MicroLogix 1500

 

 

 

 

 

only).

 

 

 

 

• Contact your Conair Service

 

 

 

 

 

representative for more information about

 

 

 

 

 

available operating systems your

 

 

 

 

 

controller.

 

 

 

 

 

0011

EXECUTABLE FILE 2 IS

Ladder File 2 is missing from the

Non-User

• Re-compile and reload the program.

 

MISSING

program.

 

 

 

 

 

 

 

 

0012

LADDER PROGRAM

The ladder program has a memory

Non-User

• Reload the program or re-compile and

 

ERROR

integrity problem.

 

 

reload the program. If the error persists, be

 

 

 

 

 

sure to use RSI programming software to

 

 

 

 

 

develop and load the program.

 

 

 

 

• Refer to proper grounding guidelines and

 

 

 

 

 

using surge suppressors in your controller’s

 

 

 

 

 

User Manual.

 

 

 

 

 

0015

I/O CONFIGURATION

The user program I/O configuration

Non-User

Re-compile and reload the program, and enter

 

FILE ERROR

is invalid.

 

the Run mode. If the error persists, be sure to

 

 

 

 

use RSI programming software to develop

 

 

 

 

and load the program.

 

 

 

 

 

 

Basic 32 Loader Control

UGC007/0702