Fault Messages and Error Codes | |
|
|
Error | Advisory Message | Description | Fault | Recommended Action |
Code |
|
| Classification |
|
(Hex) |
|
|
|
|
|
|
|
|
|
0028 | INVALID OR | • A fault routine number was | • Either clear the fault routine file number | |
| NONEXISTENT USER | entered in the status file, number |
| (S:29) in the status file, or |
| FAULT ROUTINE | (S:29), but either the fault routine |
| • create a fault routine for the file number |
| VALUE | was not physically created, or |
| reference in the status file (S:29). The file |
|
| • the fault routine number was less |
| number must be greater than 2 and less |
|
| than 3 or greater than 255. |
| than 256. |
|
|
|
|
|
0029 | INSTRUCTION | An indirect address reference in the | Recoverable | Correct the program to ensure that there are |
| INDIRECTION | ladder program is outside of the |
| no indirect references outside data file space. |
| OUTSIDE OF DATA | entire data file space. |
| |
| SPACE |
|
| Run mode. |
|
|
|
|
|
002E | EII ERROR | An error occurred in the EII | Recoverable | See the Error Code in the EII Function File for |
|
| configuration. |
| the specific error. |
|
|
|
|
|
0030 | SUBROUTINE | The JSR instruction nesting level | Correct the user program to reduce the | |
| NESTING EXCEEDS | exceeded the controller memory |
| nesting levels used and to meet the |
| LIMIT | space. |
| restrictions for the JSR instruction. Then |
|
|
|
| reload the program and Run. |
|
|
|
|
|
0031 | UNSUPPORTED | The program contains an | • Modify the program so that all instructions | |
| INSTRUCTION | instruction(s) that is not supported |
| are supported by the controller. |
| DETECTED | by the controller. |
| • |
|
|
|
| enter the Run mode. |
|
|
|
|
|
0032 | SQO/SQC/SQL | A sequencer instruction length/ | Recoverable | • Correct the program to ensure that the |
| OUTSIDE OF DATA | position parameter references |
| length and position parameters do not |
| FILE SPACE | outside of the entire data file space. |
| point outside data file space. |
|
|
|
| • |
|
|
|
| the Run mode. |
|
|
|
|
|
0033 | BSL/BSR/FFL/FFU/LFL/ | The length/position parameter of a | Recoverable | • Correct the program to ensure that the |
| LFU CROSSED DATA | BSL, BSR, FFL, FFU, LFL, or LFU |
| length and position parameters do not |
| FILE SPACE | instruction references outside of the |
| point outside of the data space. |
|
| entire data file space. |
| • |
|
|
|
| the Run mode. |
|
|
|
|
|
0034 | NEGATIVE VALUE IN | A negative value was loaded to a | Recoverable | • If the program is moving values to the |
| TIMER PRESET OR | timer preset or accumulator. |
| accumulated or preset word of a timer, |
| ACCUMULATOR |
|
| make certain these values are not |
|
|
|
| negative. |
|
|
|
| • Reload the program and enter the Run |
|
|
|
| mode. |
|
|
|
|
|
0035 | ILLEGAL | The program contains a Temporary | • Correct the program. | |
| INSTRUCTION IN | End (TND), Refresh (REF), or Service |
| • |
| INTERRUPT FILE | Communication instruction in an |
| the Run mode. |
|
| interrupt subroutine (STI, EII, HSC) or |
|
|
|
| user fault routine. |
|
|
|
|
|
|
|
0036 | INVALID PID | An invalid value is being used for a | Recoverable | Process Control Instruction for |
| PARAMETER | PID instruction parameter. |
| more information about the PID instruction. |
|
|
|
|
|
0037 | HSC ERROR | An error occurred in the HSC | Recoverable | See the Error Code in the HSC Function File |
|
| configuration. |
| for the specific error. |
|
|
|
|
|
003B | PTO ERROR | An error occurred in the PTO | Recoverable or | See the Error Code in the PTO Function File for |
|
| instruction configuration. | the specific error. | |
|
|
|
|
|
003C | PWM ERROR | An error occurred in the PWM | Recoverable or | See the Error Code in the PWM Function File |
|
| instruction configuration. | for the specific error. | |
|
|
|
|
|
Basic 32 Loader Control | UGC007/0702 |