Line 1

Line 2

Causes

Corrective Actions

Message

Message

 

 

 

 

 

 

 

SYSTEM

SYSTEM NAME

SYSTEM ID is a unique name, five

This message is for information only.

ID

 

characters or less, defined by the user.

 

 

 

 

 

You can change the system ID and name in the System Setup program (see "Using

 

 

SYSTEM NAME is a unique name, 16

the System Setup Program").

 

 

characters or less, defined by the user.

 

 

 

The system ID and name display under

 

 

 

the following conditions:

 

 

 

The system is powered on.

 

 

 

The power is off and active POST

 

 

 

 

errors are displayed.

 

 

 

 

 

E0000

OVRFLW CHECK

LCD overflow message.

Check the SEL for details on the events.

 

LOG

 

 

 

 

 

A maximum of three error messages can

 

 

 

display sequentially on the LCD. The

 

 

 

fourth message displays as the standard

 

 

 

overflow message.

 

 

 

 

 

E0119

TEMP AMBIENT

Ambient system temperature is out of

Ensure that the system cooling fans are properly installed. If the problem persists,

 

 

acceptable range.

replace the faulty fan(s) (see "System Fans").

E0119

TEMP BP

Backplane board is out of acceptable

Ensure that the system cooling fans are properly installed. If the problem persists,

 

 

temperature range.

replace the faulty fan(s) (see "System Fans"). If the problem persists, replace the

 

 

 

 

backplane board (see "SCSI Backplane Board").

 

 

 

 

E0119

TEMP CPU n

Specified microprocessor is out of

Ensure that the system cooling fans are properly installed. If the problem persists,

 

 

acceptable temperature range.

replace the faulty fan(s) (see "System Fans"). If the problem persists, ensure that the

 

 

 

 

specified microprocessor's heat sink is properly installed. If the problem persists,

 

 

 

 

replace the faulty microprocessor (see "Microprocessors").

 

 

 

 

E0119

TEMP SYSTEM

System board is out of acceptable

Ensure that the system cooling fans are properly installed. If the problem persists,

 

 

temperature range.

replace the faulty fan(s) (see "System Fans"). If the problem persists, replace the

 

 

 

 

system board (see "System Board").

 

 

 

 

E0212

VOLT 3.3

System power supply is out of acceptable

Ensure that the power supplies are properly installed. If the problem persists, replace

 

 

voltage range; faulty or improperly

the faulty power supply(s) (see "Power Supplies").

E0212

VOLT 5

installed power supply.

 

E0212

VOLT 12

 

 

 

 

 

 

 

E0212

VOLT BATT

Faulty battery; faulty system board.

Ensure that the system battery is properly installed. If the problem persists, replace

 

 

 

 

the battery (see "System Battery"). If the problem persists, replace the system board

 

 

 

 

(see "System Board").

 

 

 

 

E0212

VOLT BP 12

Backplane board is out of acceptable

Ensure that the power cables are securely connected to the backplane board (see

 

 

voltage range.

"SCSI Backplane Board"). Ensure that the power supplies are properly installed. If the

E0212

VOLT BP 3.3

 

 

problem persists, replace the faulty power supply(s) (see "Power Supplies").

E0212

VOLT BP 5

 

 

 

 

 

 

 

E0212

VOLT CPU VRM

Microprocessor VRM voltage is out of

Ensure that supported VRMs of the same type are properly installed. If the problem

 

 

acceptable range; faulty or improperly

persists, replace the VRMs (see Figure 4-29). If the problem persists, replace the

 

 

installed microprocessor VRM; faulty

system board (see "System Board").

 

 

system board.

 

 

 

 

 

E0212

VOLT NIC

Integrated NIC voltage is out of

Ensure that the power supplies are properly installed. If the problem persists, replace

 

1.8V

acceptable range; faulty or improperly

the faulty power supply(s) (see "Power Supplies"). If the problem persists, replace

 

 

installed power supply; faulty system

the system board (see "System Board").

 

 

E0212

VOLT NIC

board.

 

 

2.5V

 

 

 

 

 

 

 

E0212

VOLT PLANAR

System board is out of acceptable voltage

 

 

REG

range; faulty or improperly installed

 

 

 

system board.

 

 

 

 

 

E0276

CPU VRM n

Specified microprocessor VRM is faulty,

Ensure that supported VRMs of the same type are properly installed. If the problem

 

 

unsupported, improperly installed, or

persists, replace the VRM (see Figure 4-29).

 

 

E0276

MISMATCH VRM

missing.

 

 

n

 

 

 

 

 

 

 

 

E0280

MISSING VRM

 

 

 

 

n

 

 

 

 

 

 

 

E0319

PCI OVER

Faulty or improperly installed expansion

Ensure that the expansion cards are properly installed. If the problem persists,

 

CURRENT

card.

 

replace the faulty expansion card(s) (see "Expansion Cards").

 

 

 

 

E0412

RPM FAN n

Specified cooling fan is faulty, improperly

Ensure that the system cooling fans are properly installed. If the problem persists,

 

 

installed, or missing.

replace the faulty fan(s) (see "System Fans").

 

 

 

 

E0780

MISSING CPU

Microprocessor is not installed in the

A microprocessor must be installed in socket 1, and a VRM must be installed for each

 

n

specified socket.

installed microprocessor. Install a microprocessor in the specified socket or remove

 

 

 

 

the VRM for the specified microprocessor if that microprocessor is not installed (see

 

 

 

 

"Microprocessors"). To identify the microprocessors and VRMs, see Figure 5-3.

 

 

 

 

E07F0

CPU IERR

Faulty or improperly installed

Ensure that the microprocessors are properly installed. If the problem persists,

 

 

microprocessor.

replace the faulty microprocessor(s) (see "Microprocessors").

E07F1

TEMP CPU n

Specified microprocessor is out of

Ensure that the system cooling fans are properly installed. If the problem persists,

 

HOT

acceptable temperature range and has

replace the faulty fan(s) (see "System Fans"). If the problem persists, ensure that the

 

 

halted operation.

microprocessor heat sinks are properly installed. If the problem persists, replace the

 

 

 

 

faulty microprocessor (see "Microprocessors").

 

 

 

 

E07F4

POST CACHE

Faulty or improperly installed

Ensure that the microprocessors are properly installed. If the problem persists,

 

 

microprocessor.

replace the faulty microprocessor(s) (see "Microprocessors").

E07F4

POST CPU REG

 

 

 

 

 

 

 

E07F4

POST CPU SMI

SMI handler failed to initialize; faulty

Replace the system board (see "System Board").

 

 

system board.

 

 

 

 

 

 

Page 11
Image 11
Dell 2650 manual Line Causes Corrective Actions Message, System Setup Program