![](/images/new-backgrounds/1225070/225070153x1.webp)
|
|
| Troubleshooting Tables | ||
|
|
|
|
|
|
| What’s Happening | What’s Wrong | What You Can Do |
|
|
|
|
|
|
|
|
| When you run Check Switch, you see | • The DishPro Twin LNBF is | • If the check switch summary screen |
|
|
| "Twin" identified as the Device/LNB but | connected but the dish may not be | shows "119 W" on Dish Input 2, you |
|
|
| you only have signal confirmed from one | pointed to receive signal from both | need to point you dish 9 degrees to the |
|
|
| satellite. | 110 and 119 satellites. | east and repeak your dish. Rerun |
|
|
|
|
| check switch. |
|
|
|
|
| If the check switch summary screen |
|
|
|
|
| shows "110 W" on Dish Input 1, you |
|
|
|
|
| need to point you dish 9 degrees to the |
|
|
|
|
| west and repeak your dish. Rerun |
|
|
|
|
| check switch. |
|
|
|
|
| Make sure the skew setting is correct |
|
|
|
|
| for a Dish 500 installation at your zip |
|
|
|
|
| code. Rerun check switch. |
|
|
|
|
|
|
|
|
| When you run Check Switch, you see | • Cables may not be rated for 2150 | • Make sure cable is rated for 2150 |
|
|
| "Twin" identified as a Device or LNB, | MHz. | MHz and all accessory devices are |
|
|
| but only odd transponders are detected. |
| compatible. Rerun check switch. |
|
|
|
|
|
|
|
|
| Getting receiver messages that signal is | • Check the weather conditions to see if | • Wait for weather to clear up and |
|
|
| lost or being acquired | heavy rain or snow could be | restore signal. |
|
|
|
| temporarily block the signal. |
|
|
|
|
| • Check for any obstructions in way of | • Clear obstructions from the signal |
|
|
|
| the dish like new growth on trees | path. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*Compatible accessory devices must pass 2150 MHz signals, 22 KHz signals both directions (per DiSEqC 2.0 specifications), and pass DC power.
USING THE REMOTE CONTROL
|
|
|
|
|
| What Is | Possible Reason | What to Do |
|
| Happening |
| ||
|
|
|
| |
|
|
|
|
|
| You cannot find the | N/A | Use the receiver front panel Control Buttons to control the |
|
| remote control. |
| receiver until you find the remote. If the remote control is |
|
|
|
| permanently lost or too damaged to use, call the Service Center to |
|
|
|
| order a replacement. |
|
|
|
|
|
|
| When you press a button | The remote control may be missing | If the batteries are missing or dead, insert fresh |
|
| on the remote control, the | batteries, the batteries may be | If the remote has fresh batteries, check whether they are placed |
|
| receiver does not do what | incorrectly placed in the remote, or | according to the label diagram. If not, remove them and place |
|
| you expect. | the batteries may be weak or dead. | correctly. |
|
|
|
|
|
|
| When you press the | Other lights are too bright. | Try other remote control buttons to see if the receiver is responding. |
|
| remote control Power | Remote control not operating | Replace the remote batteries with fresh ones. |
|
| button to turn the receiver |
|
| |
| properly or the batteries are weak or |
|
| |
| ON, the receiver front | Check that the receiver power cord is not damaged, and that the |
| |
| dead. |
| ||
| panel Power light does |
| ||
| The receiver power cord not plugged | plug is inserted correctly into the outlet. |
| |
| not light up. |
| ||
| into a power outlet, or there may be |
|
| |
|
|
|
| |
|
| a problem with the power. |
|
|
|
|
|
|
|
| You use a pyramid type IR | The IR sensor on the extender that | Make sure that the extender that receives the signal from the remote |
|
| extender (not a “mouse | receives the remote control signals | control is facing the right way, so that the IR sensor can receive the |
|
| tail”), and it does not seem | may not be facing the remote | remote control signals. |
|
| to work. | control. | Make sure that the IR cable on the extender that sends the signal to |
|
|
| The IR cable on the extender that | the receiver is right in front of the IR sensor on the receiver front |
|
|
| sends the signal to the receiver may | panel, so that the receiver IR sensor can receive the signals. |
|
|
| not be right in front of the IR sensor | If doing the above does not solve the problem, contact the |
|
|
| on the receiver front panel. | manufacturer of the extenders for assistance. |
|
|
|
|
|
|
|
|
|
|
|
Page 85