Manuals / Dolby Laboratories / Home Audio / Stereo Amplifier

Dolby Laboratories manual Hum Problems, Room lighting dimmer controls SCR-TYPE, Model CP65

Models: CP65

1 82

Download 82 pages 36.23 Kb

Page 22

Model CP65

2-16

STEP 11 Turn the front pannel FADER fully down, then connect the CP65 to mains power.

Model CP65

STEP 12 With the NORMAL/BYPASS switch (accessible with the front door open) in the NORMAL position, verify that all three LEDs on the Cat. No. 249 Power Supply Module are lit. Close the front door and verify that format 04 Dolby stereo optical with surround, local active, and proj 1 or proj 2 LEDs are on (unless a different wake-up format was selected on the Cat. No. 443).

STEP 13 Select each format in turn, using the buttons on the front panel and check that the associated LED lights.

STEP 14 Press the MUTE pushbutton switch; the LED on the switch should blink. Press the MUTE pushbutton switch again; the LED on the switch should be off.

STEP 15 Set the NORMAL/BYPASS switch to the BYPASS position. The bypass LED on the front panel should blink and all other LEDs should be off.

STEP 16 Return the NORMAL/BYPASS switch back to the NORMAL position and apply power to the other projection room equipment.

HUM PROBLEMS

If you hear undesirable hum from the speakers when you apply power to the CP65 and other projection room equipment, check the following list for possible causes:

1.Ground loops caused by audio signal wiring, especially to power amplifiers. Only one end of an audio shield wire should be connected. See Pages 2- 3 and 2-4. Be sure to check the booth monitor installation.

The CP65 backplane contains a link which connects frame ground to signal/power ground (TB2 terminals 8 and 9). If you have checked items 1 through 7 and hum is still present, removing this link may fix the problem.

2.Projector power wiring. All mains wiring should be properly grounded.

3.Room lighting dimmer controls (SCR-TYPE).

Image 22

Dolby Laboratories manual Hum Problems, Room lighting dimmer controls SCR-TYPE, Model CP65

Contents

Installation and Alignment Instructions Model CP65 Cinema ProcessorDolby Laboratories Inc Dolby Laboratories Inc U.S. HeadquartersU.K. European Office 100 Potrero Avenue San Francisco, CA TelephoneINTRODUCTION Table of ContentsINITIAL SET-UPAND INSTALLATION EQUIPMENT REQUIREDAPPENDIX C APPENDIX AAPPENDIX B APPENDIX D04 Dolby Stereo A-type 05 Dolby Stereo SR INTRODUCTIONCP65 60 Non-syncPage 1 Dolby Tone and Pink Noise - Cat. No SECTION EQUIPMENT REQUIRED2 1kHz, 100% Modulation, Left/Right - Cat. No 4Stereo Optical Surround Level - Cat. No TEST FILM3SMPTE Buzz Track JIFFYSECTION INITIAL SET-UPAND INSTALLATION Acceptable SettingVoltage Voltage RangeCat. No Cat. No. 242, B-ChainCard Cat. No. 249, Power Supply ModuleJ5 J6 J7 J8 Cat. No. 443, Control Logic Card J3 INCP65 Backplane Standard CP65 or CP65AIn a CP65-300when Cat. No. 300 modules are fitted in place of the normal Cat. No. 350 modules J16 and J18 should be rotated so that the words “Format 42” appears the right way up. With J24 in the “NR” position input signals will be A-typedecoded when the Mag/Aux format is selected. With J24 in the “NO NR” position signals pass through the noise reduction modules but the processing will be turned off. If both of these processing options are required frequently an external switch may be connected to J24 CP65-300J1 Optical Bass Extension output level sets the output level range for the subwoofer channel. In the HIGH position J1 is set at the factory for a power amplifier input sensitivity of between 90 mV and 1.23 V. If the power amplifiers used in the installation are very sensitive 10 mV to 100 mV input sensitivity, it may be necessary to set J1 to the LOW position. If you are unsure of the sensitivity of your power amplifiers set J1 to the LOW position initially. If the high output position is required this will be determined during OBE alignment Slot selected projector. Electronic switches selectCard Descriptions Card2 4 Channel Decoder Two-channelNoiseReduction Module 7,8,9Function SlotCard Cat. NoFuse Voltage SettingInternational TypeIMPORTANT SAFETY NOTICE IEC NOTICESGB F D I E S NL IMPORTANT - NOTE DE SECURITE3.Room lighting dimmer controls SCR-TYPE HUM PROBLEMSModel CP65 With CP65 FADER turned up and format 04 selected 1. Aligning the A-Chain SECTION AN OVERVIEW OF THE ALIGNMENT PROCEDURE2. Aligning the B-Chain and with a broad range of speakers. Accurate equalization requires the use of standardized acoustic measurement procedures Many loudspeakers used in theatres are far from ideal and require boosting of the low- and high-frequencyextremes in order to produce an approximation of the standard reference response curve. Bass and treble controls-centeredon the turnover points of typical loudspeakers-liftthe ends of the spectrum without the need for large amounts of narrow- band boost from the third-octavecontrols in the Cat. No. 64 cards. The third-octavecontrols are used for minor adjustments that are required to smooth the frequency response curve SECTION A-CHAINALIGNMENT Action a. Preliminary Proceduresa. Preliminary Procedures Notes Indicationa. Preliminary Procedures Notes A-ChainAlignment Proceduresa. Preliminary Procedures ActionAction b. Optical Preamplifier Adjustmentsb. Optical Preamplifier Adjustments Notes Indicationb. Optical Preamplifier Adjustments Notes A-ChainAlignment Proceduresb. Optical Preamplifier Adjustments Actionb. Optical Preamplifier Adjustments L L R R L L R RCAT NO b. Optical Preamplifier Adjustments NotesCAT. NO. 97 TEST FILM ActionIndicationn REPEATA-ChainAlignment Procedures OSCILLOSCOPE TRACESRTA DISPLAY b. Optical Preamplifier AdjustmentsA-ChainAlignment Procedures 12 ANDREPEAT b. Optical Preamplifier Adjustmentsb. Optical Preamplifier Adjustments CAT NOFOR PROJECTOR NO. REPEAT 1 → b. Optical Preamplifier Adjustments Notesc. Magnetic Preamplifier Adjustments Magnetic Alignmentc. Magnetic Preamplifier Adjustments A-ChainAlignment ProceduresMagnetic Alignment SECTION B-CHAINALIGNMENT bypass a. Setting Room Equalizationa. Setting Room Equalization Notes Actiona. Setting Room Equalization Notes Loudspeakers and Crossoversa. Setting Room Equalization ActionGeneral bypassAmplifiers a. Setting Room EqualizationAction B-ChainAlignment Proceduresa. Setting Room Equalization Notes Indicationa. Setting Room Equalization Notes REPEATa. Setting Room Equalization Actiona. Setting Room Equalization Notes B-ChainAlignment Proceduresa. Setting Room Equalization Actiona. Setting Room Equalization Notes Do not adjusta. Setting Room Equalization ActionAction a. Setting Room Equalizationa. Setting Room Equalization Notes IndicationL 14 → 21 R 14 → b. Adjusting L,C,R Gainb.Adjusting L,C,R Gain 22REPEAT79 dBC c. Setting Mono Gainc. Setting Mono Gain Notes ActionB-ChainAlignment Procedures d. Subwoofer Alignment Cat. Nod. Subwoofer Alignment Cat. No. Notes Actiond. Subwoofer Alignment Cat. No 90 dBCB-ChainAlignment Procedures Actiond. Subwoofer Alignment Cat. No FROMd. Subwoofer Alignment Cat. No ActionAction Select format 04 Dolby Stereo A-Typed. Subwoofer Alignment Cat. No REPEATd. Subwoofer Alignment Cat. No SAME ASd. Subwoofer Alignment Cat. No Actione. Surround Equalization Alignment Cat. No Re Se. Surround Equalization Alignment Cat. No Actione. Surround Equalization Alignment Cat. No ActionAction e. Surround Equalization Alignment Cat. NoREPEAT e. Surround Equalization Alignment Cat. No 88 dBCAction Action B-ChainAlignment Procedurese. Surround Equalization Alignment Cat. No Indicationmsec f. Adjustment of Surround DelayThumbwheel Switch Settingxx dBC g. Adjustment of Bypass Gaing. Adjustment of Bypass Gain Notes B-ChainAlignment Proceduresg. Adjustment of Bypass Gain FROM xx dBC -3dB yy dBCB-ChainAlignment Procedures g. Adjustment of Bypass Gain NotesPress the format 60 non sync switch h. Adjustment of Non-syncGainh. Adjustment of Non-syncGain Notes ActionAction h. Adjustment of Non-syncGainh. Adjustment of Non-syncGain Notes Indication5REPEAT PAGE 5-20STEP i. Adjustment of Mono Gain and Equalizationi.Adjustment of Mono Gain and Equalization Notes B-ChainAlignment Proceduresj. Final Checks Press the format 04 Dolby Stereo A-type switchJIFFY TEST FILM j. Final Checks NotesSECTION REFERENCE DIAGRAMS Cat. No. 222 Dual Noise Reduction Module INPUTS OUTPUTSPage Cat. No. 242 B-ChainFacilities Card Cat. No. 249 Power Supply Card Cat. No. 259 Transformer Module INPUTS OUTPUTSCat. No. 443 Control Logic Card +24V CP65 POWER DISTRIBUTION TABLECat. No +15VAPPENDIX A CHECKING PHASING OF SPEAKERS 10,000 Frequency in Hz5,000 20,0001.Operation APPENDIX C CP65M MONO INSTRUCTIONS2.Cat. No. 327A Circuit Description C.2 Schematic Cat. No. 327A A3C2984 revTerminal Block TB1 APPENDIX D BACKPLANE CONNECTIONS LISTCP65 Backplane Connections Terminal Block TB2D connector J18