Mini-monitor Commands | Eicon Networks DIVA T/A ISDN Modem specification

Mini-monitor Commands

The following commands relate to the Mini-monitor. They are all case sensitive.

Your Eicon Technology Customer Services representative may ask you to use these commands.

at@dump	Dump Memory. Produces a memory dump using XMODEM.
	Note: This command needs a terminal emulation program that supports XMODEM.

at@d1	DRAM test.

at@d2	Flash test.

at@d3	ISDN internal loop back test.

at@d4	ISDN external loop back test.

at@fail	Simulate a fault.

at@load	Load New Firmware.
	Note: This command needs a terminal emulation program that supports XMODEM or
	1K-XMODEM.

at@md arg	Display memory (arg= “address:size”).

at@msg	Display cause for entering the monitor.

at@quit	Exit the Mini-monitor.

at>F	Restore All Profiles to Original Factory Settings. Reverts the powerup profile to
	number 0.
	Warning: All previous user-defined settings are lost.

DIVA T/A ISDN Modem Reference Guide ◆ Page 62

Image 62

Eicon Networks DIVA T/A ISDN Modem manual Mini-monitor Commands

Contents

Diva T/A Isdn Modem Reference Guide Eight Edition July 206-193-08 Contents What is ISDN? Diva T/A Isdn Modem Reference Guide What is ISDN? Isdn Communication Channels Channel Channel Connecting to Isdn BRI and PRI Basic Rate Access What is Multilink PPP? What is BACP/BOD? What is DBA? What is Always On / Dynamic Isdn AO/DI? What is Data Compression? Locating AT Commands Locating AT Commands AT Command Groups Alphabetical List of Supported AT Commands AT! Commands Alphabetical List of Supported AT Commands Alphabetical List of Supported AT Commands AT% Commands AT& Commands AT* Commands AT Commands AT@ Commands Other AT Commands Registers AT$ Utility Commands Mini-monitor Commands General AT Commands General AT Commands Values for n Isdn Configuration CommandsDefaults Isdn Configuration Commands INS-Net64, NI-1, or 5ESS, µ law will be used default None defaultDefault1 AT!D3=n Number. Numbers are separated by a semicolon Default null string this is an optional valueAT!N2=n AT!N3=n On region 255 do not attempt 56k data call retry For more details, refer to the Rvscom documentationAT!X56=n COM Port Configuration Commands COM Port Configuration Commands Ring For example, Connect Upon connection, the Diva T/A reports the DCE speed Call Control Commands Call Control Commands ATA ATH Configuration Commands Configuration Commands Use the default settings AT!V0=n Profile Commands Multilink PPP Commands Multilink PPP Commands Internet Protocol IP Endpoint Discriminator Class/AddressAT%M3=b3c665ac11 Always On / Dynamic Isdn AT Commands Always On / Dynamic Isdn AT Commands Default 1000 bytes AT!X13=n when Bacp is disabled, seeWill be opened after the delay specified by AT!X10 AT!X14=n AT!X18 Default values for each setting, and is defined as followsDefault AT!X22=n Defined as follows Connection numbers affects the range ofAT!X21. SeeAT!X21 Default CF PPP overAT!X25=n AT!X26=n Utility Commands Start or display the Result of a Lapd trace Utility CommandsInternal TA access command reserved for VU Start or Display the Result of a PPP trace Start an AO/DI X.25 Trace Enter the monitor on the next resetSoft reset the unit and enter the monitor Register Commands AT? Register Commands Analog Device Commands Analog Device Commands AT*Fn Enable with default values default To be disabledDisable. Recommended for modem/fax calls Enable using same terminal endpoint identifier as data port Mini-monitor Commands AT Command Result Codes Carrier Connect AT Command Result CodesConnect Connect 1200T/75R Protocol Transparent ModeConnect 75T/1200R Protocol None Index BACP/BOD