Analog Device Commands | Eicon Networks DIVA T/A ISDN Modem guide

Analog Device Commands

The following table describes the analog device commands. These commands are only available on units with the optional analog device ports.

AT*An=v	Abbreviated Ring Control (North America only). Specifies whether Visual Message
	Waiting's abbreviated ring is enabled or disabled.
	n=1	Analog device port 1 (PHONE 1).
	n=2	Analog device port 2 (PHONE 2).
	v= 0	Disabled.
	v=1	Enabled (default).

AT*Bn=v	ISDN Bearer Capability. Specifies the bearer capability for ISDN calls on the analog
	device interface.
	n=1	Analog device port 1 (PHONE 1).
	n=2	Analog device port 2 (PHONE 2).
	v=0	Outgoing analog device calls use Speech encoding (default).
	v=1	Outgoing analog device calls use Audio 3.1Khz encoding. This setting is
		recommended for modem/fax calls.
	Note: This parameter does not take effect until you restart your DIV AT/A.

AT*Cn	Analog Device Caller ID Delivery. Specifies whether analog device caller ID delivery
	is enabled or disabled (North America only). When enabled telephones with Call Display
	will display incoming call information.
	n=0	Disable analog device caller ID delivery.
	n=1	Enable analog device caller ID delivery (default).
	Note: This parameter does not take effect until you restart your DIV AT/A.

AT*Dn=v	Internal Dial Access. Controls the internal dial access for supplementary services.
	n=1	Analog device port 1 (PHONE 1).
	n=2	Analog device port 2 (PHONE 2).
	v=0	Disable internal dial access. This setting is recommended for modem/fax calls.
	v=1	Enable internal dial access (default).
	Note: This parameter does not take effect until you restart your DIV AT/A.

AT*En=v	Enable/disable Incoming and Outgoing Calls. Specifies the type of calls (outgoing
	and incoming) permitted on an Analog Port. Each Analog port can be set
	independently.
	n=1	Analog device port 1 (PHONE 1).
	n=2	Analog device port 2 (PHONE 2).
	v=0	Disable port.
	v=1	Outgoing calls only.
	v=2	Incoming calls only.
	v=3	Incoming and outgoing calls (default).

DIVA T/A ISDN Modem Reference Guide ◆ Page 59

Image 59

Eicon Networks DIVA T/A ISDN Modem manual Analog Device Commands

Contents

Diva T/A Isdn Modem Reference Guide Eight Edition July 206-193-08 Contents Diva T/A Isdn Modem Reference Guide What is ISDN? What is ISDN? Channel Isdn Communication Channels Channel Basic Rate Access Connecting to Isdn BRI and PRI What is Multilink PPP? What is BACP/BOD? What is DBA? What is Always On / Dynamic Isdn AO/DI? What is Data Compression? Locating AT Commands Locating AT Commands AT Command Groups Alphabetical List of Supported AT Commands Alphabetical List of Supported AT Commands AT! Commands Alphabetical List of Supported AT Commands AT% Commands AT& Commands AT* Commands AT Commands AT@ Commands Other AT Commands Registers AT$ Utility Commands Mini-monitor Commands General AT Commands General AT Commands Values for n Isdn Configuration CommandsDefaults Isdn Configuration Commands AT!D3=n None defaultDefault1 INS-Net64, NI-1, or 5ESS, µ law will be used default AT!N3=n Default null string this is an optional valueAT!N2=n Number. Numbers are separated by a semicolon On region 255 do not attempt 56k data call retry For more details, refer to the Rvscom documentationAT!X56=n COM Port Configuration Commands Ring COM Port Configuration Commands Upon connection, the Diva T/A reports the DCE speed For example, Connect Call Control Commands ATA Call Control Commands ATH Configuration Commands Configuration Commands AT!V0=n Use the default settings Profile Commands Multilink PPP Commands Multilink PPP Commands Internet Protocol IP Endpoint Discriminator Class/AddressAT%M3=b3c665ac11 Always On / Dynamic Isdn AT Commands Always On / Dynamic Isdn AT Commands AT!X14=n AT!X13=n when Bacp is disabled, seeWill be opened after the delay specified by AT!X10 Default 1000 bytes Defined as follows Default values for each setting, and is defined as followsDefault AT!X22=n AT!X18 AT!X26=n Default CF PPP overAT!X25=n Connection numbers affects the range ofAT!X21. SeeAT!X21 Utility Commands Start or Display the Result of a PPP trace Utility CommandsInternal TA access command reserved for VU Start or display the Result of a Lapd trace Start an AO/DI X.25 Trace Enter the monitor on the next resetSoft reset the unit and enter the monitor AT? Register Commands Register Commands Analog Device Commands AT*Fn Analog Device Commands Enable using same terminal endpoint identifier as data port To be disabledDisable. Recommended for modem/fax calls Enable with default values default Mini-monitor Commands AT Command Result Codes Carrier Connect AT Command Result CodesConnect Protocol None Protocol Transparent ModeConnect 75T/1200R Connect 1200T/75R BACP/BOD Index