AT Command Result Codes | Eicon Networks DIVA T/A ISDN Modem

AT Command Result Codes

DCE Speed means different things for different applications. For Digital calls, it is the bitrate obtained by summing all ISDN B-channels available to the protocol. For a V.110 call, it is the V.110 user rate and not the intermediate rate of the B-channel. For Modem over ISDN, it is the speed of the V.34 carrier.

DTE Speed is the speed used between the PC and the T/A (default configured or last speed detected by the auto-bauding process). Some non-standard speeds (e.g. using certain divisors on a PC 8250 or 16550 UART) are not detected by the DIVA T/A and will not be correctly reported.

Code	Word Message
1	CONNECT

5CONNECT 1200

10 CONNECT 2400

11 CONNECT 4800

12 CONNECT 9600

13 CONNECT 7200

14 CONNECT 12000

15 CONNECT 14400

16 CONNECT 19200

17 CONNECT 38400

18 CONNECT 57600

19 CONNECT 64000

20 CONNECT 115200

21 CONNECT 230400

23 CONNECT 512000

40	CARRIER 300	CONNECT 300

41	CARRIER 600	CONNECT 600

46	CARRIER 1200	CONNECT 1200

47	CARRIER 2400	CONNECT 2400

48	CARRIER 4800	CONNECT 4800

49	CARRIER 7200	CONNECT 7200

50	CARRIER 9600	CONNECT 9600

51	CARRIER 12000	CONNECT 12000

52	CARRIER 14400	CONNECT 14400

53	CARRIER 16800	CONNECT 16800

DIVA T/A ISDN Modem Reference Guide ◆ Page 64

Image 64

Eicon Networks DIVA T/A ISDN Modem manual AT Command Result Codes, Carrier Connect

Contents

Diva T/A Isdn Modem Reference Guide Eight Edition July 206-193-08 Contents What is ISDN? Diva T/A Isdn Modem Reference Guide What is ISDN? Isdn Communication Channels Channel Channel Connecting to Isdn BRI and PRI Basic Rate Access What is Multilink PPP? What is BACP/BOD? What is DBA? What is Always On / Dynamic Isdn AO/DI? What is Data Compression? Locating AT Commands Locating AT Commands AT Command Groups Alphabetical List of Supported AT Commands AT! Commands Alphabetical List of Supported AT Commands Alphabetical List of Supported AT Commands AT% Commands AT& Commands AT* Commands AT Commands AT@ Commands Other AT Commands Registers AT$ Utility Commands Mini-monitor Commands General AT Commands General AT Commands Defaults Isdn Configuration CommandsValues for n Isdn Configuration Commands None default Default1INS-Net64, NI-1, or 5ESS, µ law will be used default AT!D3=n Default null string this is an optional value AT!N2=nNumber. Numbers are separated by a semicolon AT!N3=n AT!X56=n For more details, refer to the Rvscom documentationOn region 255 do not attempt 56k data call retry COM Port Configuration Commands COM Port Configuration Commands Ring For example, Connect Upon connection, the Diva T/A reports the DCE speed Call Control Commands Call Control Commands ATA ATH Configuration Commands Configuration Commands Use the default settings AT!V0=n Profile Commands Multilink PPP Commands Multilink PPP Commands AT%M3=b3c665ac11 Endpoint Discriminator Class/AddressInternet Protocol IP Always On / Dynamic Isdn AT Commands Always On / Dynamic Isdn AT Commands AT!X13=n when Bacp is disabled, see Will be opened after the delay specified by AT!X10Default 1000 bytes AT!X14=n Default values for each setting, and is defined as follows Default AT!X22=nAT!X18 Defined as follows Default CF PPP over AT!X25=nConnection numbers affects the range ofAT!X21. SeeAT!X21 AT!X26=n Utility Commands Utility Commands Internal TA access command reserved for VUStart or display the Result of a Lapd trace Start or Display the Result of a PPP trace Soft reset the unit and enter the monitor Enter the monitor on the next resetStart an AO/DI X.25 Trace Register Commands AT? Register Commands Analog Device Commands Analog Device Commands AT*Fn To be disabled Disable. Recommended for modem/fax callsEnable with default values default Enable using same terminal endpoint identifier as data port Mini-monitor Commands AT Command Result Codes Connect AT Command Result CodesCarrier Connect Protocol Transparent Mode Connect 75T/1200RConnect 1200T/75R Protocol None Index BACP/BOD