Emerson 480V, 60HZ Appendix A - Ups Status Messages, UPS status messages, UPS Status Messages

UPS Status Messages

APPENDIX A - UPS STATUS MESSAGES

Table 39 shows all event messages as they appear in the current status area of the LCD and in the history log, along with a description and recommended actions, if any. For further information on the current status area and the history log, see 2.11 UPS Status Messages.

Table 39 UPS status messages

Event Message	Description / Suggested Action (if any)
Inverter Comm. Fail	The RS-485 communication between internal monitor and inverter has failed. Contact Liebert
	Services at 800-543-2378 for assistance.
Rectifier Comm. Fail	The RS-485 communication between internal monitor and rectifier fails. Contact Liebert
	Services at 800-543-2378 for assistance.
	The CAN communication between different UPS units within a parallel system has failed.
	Check if there are some UPS units not powered on in the parallel system. If so, power on these
Parallel Comm. Fail	UPS units and check if the alarm disappears.
	Press Fault Clear push button.
	If alarm does not clear, contact Liebert Services at 800-543-2378
Battery Overtemp.	The battery temperature is over limit. Check the battery temperature and ventilation
Ambient Overtemp.	The ambient temperature is over limit. Check the ventilation of UPS room.
Replace Battery	Battery should be replaced. Contact Liebert Services at 800-543-2378 for assistance.
	Before the end of discharging, battery under-voltage pre-warning should occur. After this pre-
Battery Low Pre-warning	warning, battery should have the capacity for 3 minutes discharging with full load. The time is
	user configured from 3 to 60 minutes.
	Shut down the load in time to prevent damage to equipment and data.
Battery End of Discharge	Inverter turned off due to low battery voltage.
	Check the utility failure and try to recover it.
Mains Volt. Abnormal	Mains voltage exceeds the upper or lower limit and results in rectifier shutdown.
	Check the input line-to-line voltage amplitude of rectifier.
Mains Undervoltage	Mains voltage is undervoltage 288V~384V line to line voltage with derated load.
	Check the input line-to-line voltage amplitude of rectifier.
Mains Freq. Abnormal	Mains frequency is out of limit range and results in rectifier shutdown.
	Check the rectifier’s input voltage frequency
Rectifier Fault	Contact Liebert Services at 800-543-2378 for assistance.
	The temperature of rectifier inductor of rectifier common mode inductor is too high to keep the
Input Inductor Overtemp.	rectifier running.
	Check the ambient temperature and ventilation; contact Liebert Services at 800-543-2378 for
	assistance.
Rectifier Overtemp.	The temperature of the heat sink is too high to keep the rectifier running.
	The UPS can recover automatically. Check the environment and ventilation.
Charger Fault	The charger has a fault. Contact Liebert Services at 800-543-2378 for assistance.
Control Power 1 Fail	Control Power 1 has failed or has been lost. Contact Liebert Services at 800-543-2378 for
	assistance.
Mains Phase Reversed	Input phase sequence is inverse. Contact Liebert Services at 800-543-2378 for assistance.
Rectifier Overcurrent	The current of rectifier is over limit. Contact Liebert Services at 800-543-2378 for assistance.
Soft Start Fail	Rectifier could not start due to low DC bus voltage. Contact Liebert Services at 800-543-2378
	for assistance.
	This alarm is triggered by an inverter software routine when the amplitude or frequency of
	bypass voltage is beyond the normal range.
	The amplitude threshold is fixed for positive and negative 10% rating.
	This alarm automatically resets once the bypass voltage goes normal.
Bypass Unable to Trace	First verify that the bypass voltage and frequency displayed on the panel is within the selected
	range. Note here the rated voltage and frequency are specified by “Output voltage level” and
	“Output frequency level” respectively.
	If the displayed voltage is believed to be abnormal, then verify the bypass voltage and frequency
	presented to the UPS. Check the external supply if it is found to be faulty.
	Contact Liebert Services at 800-543-2378 for assistance.

97