Manuals / Emerson / Computer Equipment / Power Supply

Emerson Series 610 Rating, Specifications, Output power envelope for 0.8 and 0.9 pf rated units

Models: Series 610

1 120

Download 120 pages 16.72 Kb

Page 114

5.0SPECIFICATIONS

Specifications

5.0SPECIFICATIONS

5.1Rating

The kVA and kW ratings and the nominal voltages and currents for continuous operation are listed on the unit nameplates (inside Operator Control Panel door) and on the System One-Line Diagram. The rated output power envelope of the UPS is illustrated in Figure 70. The UPS is rated to deliver rated kVA and rated kW at 0.8 lagging power factor (pf), or 0.9 lagging pf for some models. However, the UPS will operate connected loads with power factors ranging from 0.7 lagging through 1.0 (unity).

Connected load kW and kVA are both displayed on the LCD screen when the UPS is powering the load. The approximate connected load power factor may be easily calculated by kW ÷ kVA = pf.

For load power factors between 0.7 lagging and the rated power factor (usually 0.8 or 0.9), the full kVA rating of the unit is available. However, above the rated pf the kW rating will become the limit- ing factor. Note that some models are specifically rated for a 0.9 lagging output power factor.

For loads with power factors below 0.7 lagging or with leading power factors, the UPS output is kVA limited and the UPS System may not meet all of its output performance specifications. Contact Lie- bert Global Services at 1-800-LIEBERT to request assistance for these applications.

Figure 70 Output power envelope for 0.8 and 0.9 pf rated units

	kW
	1.0
	0.9
	0.9 x kVA
LEADING	0.8	LAGGING
power factor (pf)	0.8 x kVA	power factor (pf)
	0.7 x kVA	0.7
	0.7 x kVA

Contact Liebert for	Contact Liebert for
load operation in this	load operation in this
area	area

Rated kVA

108

Image 114

Emerson Series 610 manual Rating, Specifications, Output power envelope for 0.8 and 0.9 pf rated units

Contents

Liebert Series 610 UPS AC PowerFor Business-Critical Continuity BATTERY CABINET PRECAUTIONS CONTACTING LIEBERT FOR SUPPORTTABLE OF CONTENTS 4.0 MAINTENANCE 5.0 SPECIFICATIONSFIGURES TABLES IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS1.1 System Description 1.0 INTRODUCTIONFigure 1 Multi-Module UPS, 100-500kVA Figure 2 Multi-Module UPS, 500-750kVA Designed for Success 1.2 ReliabilityTypes of System Control Cabinets SCCs Figure 3 System Control Cabinets1.4 Modes of Operation 1.3 Safety Precautions1.4.2 Input Power Failure Other Factors to Consider1.4.3 Recharge 1.4.7 Maintenance Bypass1.4.8 Off-Battery 1.4.4 OverloadIntroduction 1. Battery 1.6 Options2. Battery Racks or Cabinets 2.1 General Component Descriptions 2.0 THEORY OF OPERATION2.1.1 System Control Cabinet 2.1.3 Battery Plant Figure 6 UPS module block diagram2.1.2 UPS Module 2.2 Detailed Component Descriptions 2.2.1 Controls HardwareSoftware Operation Input Power Factor2.2.2 Rectifier/Charger Input Circuit BreakerBattery Charge Current Limiting 2.2.3 Battery Charging CircuitBattery Disconnect Battery Equalize Charge Circuit2.2.4 Inverter Non-Linear Load CharacteristicsUnbalanced Load Characteristics OperationFuse Protection Figure 7 System Control Cabinet block diagram2.2.5 Static Bypass Shorted SCR MonitoringStatic Switch Isolation Pulsed Parallel OperationLoad Transfers 2. Manual Transfers Transfer and Retransfer Conditions1. Automatic Transfers to Bypass 3. Transfer Inhibited2.2.6 Redundant Mode 6. Retransfer InhibitedFeatures 3.1 Display Screen and Operator Controls3.0 OPERATION Operation Figure 8 Typical operator controlsTypical operator controls 500kVAFigure 9 Operator controls, typical SCCT System Control Cabinet Typical SCCT System Control Cabinet operator controlsOperation Figure 10 Liebert Series 610 UPS and SCC operator control panels Liebert Series 610 UPS and SCC operator control panelsOperation Figure 11 Switches behind SCC control panel door Liebert Series 610 UPS and SCC operator control panelsOperation 3.2 Menu Tree Navigation Figure 12 Menu tree3.2.1 Master Menu Screen Figure 13 SCC and module master menu screensFrom any primary screen accessed directly from the Master Menu, pushing the Select pad once will return you to the Master Menu. From any secondary screen, pushing the Select pad twice will return you to the Master Menu Output Metering Displays 3.2.2 SCC Monitor/Mimic Display ScreenInput Metering Displays Figure 14 SCC Monitor/Mimic display screenItem 5 - Module Status Messages Status/Alarm Message AreasItem 7 - Alarm Messages Item 6 - System Status MessagesInput Metering Displays BATTERY VOLTS AMPS 15 CHARG3.2.3 Module Monitor/Mimic Display Screen Output Metering DisplaysAlarm Messages Item 5 - Alarm MessagesSCC Display Figure 16 Monitor/Mimic display example Normal power flowOperation Module DisplayFigure 17 Monitor/Mimic display example Utility fail OperationOperation 270 kVA / 217 kW325A 325A 325A A B C 953A3780A 953A3780A 953A378A0A OperationMOD 1 ON LINE MVODLTS2 OFF540 LINE SUM ALM MODAMPS3 75ON15 CHARGLINE 50.0Hz 5060..00HzOperation MODAMPS3 75OFFCHARGLINE SUM ALM3.2.4 Walk-In Display Screen Figure 21 Walk-in display screen during start-upEach of the four Status Reports can be displayed on a remote terminal 3.2.5 Status Reports ScreensPresent Status Refer to 3.2.15 - Communication InterfacesFigure 24 Event history report screen Event HistoryFigure 23 Present status report screens, SCC above and module OperationHistory Status Figure 25 History status report screensTable 5 Alarm conditions that freeze history data gathering Alarm in SCCAlarm in Module Figure 26 Battery cycle monitor screen System StatusEvent Figure 27 Battery cycle monitoring summary screenBattery Cycle Monitoring Summary Date3.2.6 System Configuration Screens Figure 29 SCC system configuration screenDate Figure 30 Date screenTime Figure 31 Time screenFigure 32 Auto dial setting screen Auto DialFigure 33 Modem baud rate Modem Baud RateMaximum Auto-Retransfer Attempts Figure 34 Maximum auto-retransfer attempts screenSystem Options System Current RatingLanguage Selection Figure 35 SCC system options screenFigure 37 Battery test screen-MMU only Figure 38 Battery test results screenContinuous Duty Static Switch Optional Figure 39 Monitor/Mimic display example Continuous Duty Static Switch Remote MonitorSCC and module remote monitor indications 3.2.7 Alarm Limit Settings Screen Figure 40 Module alarm limit settings screenBattery Float Voltage Temperature Limit Setting Optional3.2.8 Load Transfer Procedures Screen Figure 41 Load transfer procedures screen3.2.9 Start-Up Procedures Screen Figure 42 SCC start- up procedures screen3.2.10 Shutdown Procedures Screen Figure 43 Module start- up procedures screensFigure 44 SCC shutdown procedures screen Figure 45 Module shutdown procedures screen3.2.11 Battery Time Screen Module Only Figure 46 Battery time screen 15 minute dischargeRemaining Figure 47 Battery time screen 45-minute dischargeFigure 48 Accuracy range of values for calculated battery times TimeDirty battery jar covers Battery age Excessive battery discharge/recharge cyclesLoose electrical connections Ambient temperature extremes Bad or weak cells Low acid levels in flooded cells3.2.12 Meter Calibration Screen Figure 49 Meter calibration screen3.2.13 Battery Equalize Screen Figure 50 Battery equalize screen3.2.14 Alarm and Status Messages Module Status Messages Figure 51 SCC status and alarm message areasSystem Status Messages Alarm Messages Table 8 Abbreviations used in alarm messagesLoad Block Messages Alarm messages - meaning and corrective action OperationAlarm messages - meaning and corrective action continued OperationAlarm messages - meaning and corrective action continued Refer to 3.2.14 - Alarm and Status MessagesOperation Alarm messages - meaning and corrective action continued OperationDetermine the cause of the emergency condition and correct it if possible Operation Table 10 Alarm messages - summaryAlarm Message Special FunctionsAuto-Dial 3.2.15 Communication InterfacesWorldwide Reporting Requesting InformationLocal Reporting to a Terminal Local Reporting to a MonitorSite Reporting SiteScan or SNMP Table 11 Liebert Series 610 terminal commands Remote Monitor PanelSeparate / Simultaneous Outputs Abbreviation 3.3 Modes of OperationTable 12 Circuit breaker abbreviations Circuit BreakerSCCT 3.3.1 Load on Bypass3.3.2 OK to Transfer Figure 52 Load on bypass, UPS not availableFigure 53 Load on bypass, UPS available SCCTSCCT Figure 54 Load on UPS, bypass available3.3.3 Momentary Overloads Figure 55 Momentary overload, pulsed static bypass switchSCCT SCCT3.3.4 Input Power Failure-Load on Battery Figure 56 Input power fail-load on batterySCCT 3.3.5 One Module Off-Line SCCTFigure 57 One module off-line, load on UPS 3.3.6 Off Battery Figure 58 Load on UPS-battery not availableSCCT 3.3.7 Emergency Modules Off SCCTFigure 59 Emergency modules off 3.3.8 Remote Emergency Power Off Figure 60 Emergency power offSCCT SCCT 3.3.10 Maintenance Bypass3.3.9 System Shutdown Figure 61 System shutdownSCCT Figure 62 Load on maintenance bypass, two breakersFigure 63 Load on maintenance bypass, three breakers SCCT3.4 Manual Procedures 3.4.1 SCC Start-Up ProcedureStep 1. Before you apply power to the UPS modules, determine the position of the following circuit breakers and switches 5. Set the Static Switch Disconnects to ON closed Figure 64 SCC start-up procedures screen 3.4.2 UPS Module Start-Up Figure 65 Module start-up procedures screen The Battery block in the Monitor/Mimic Display indicates the battery voltage and charge current 3.4.3 Load Transfer Procedures Figure 66 Load transfer procedures screen3.4.4 Maintenance Bypass Load Transfers If the load is on Maintenance BypassIf the load is on the UPS System Bypass 3.4.5 Shutdown Procedures System Shutdown Procedure Figure 67 SCC shutdown procedures screenModule Shutdown Procedure Figure 68 Module shutdown procedures screenRemote Emergency Power Off REPO 3.5 Automatic OperationsLocal Emergency Modules Off LEMO 3.5.1 Overloads Without Transfer 3.5.2 Automatic Transfers to BypassFigure 69 Current-versus-time curves of module overload capacity 3.5.3 Automatic Retransfers to UPS 3.5.4 Automatic Module Off-Line3.5.5 Automatic Emergency Modules Off 4.1 Safety Precautions 4.0 MAINTENANCEProfessional Start-Up 4.2 Liebert Global ServicesMaintenance Agreements The Signature Program Training4.3 Routine Maintenance 4.3.1 Record Log4.3.2 Air Filters 4.3.3 Limited Life Components 4.4 Battery Maintenance 4.4.1 Battery Safety PrecautionsInstructions Importantes Concernant La Sécurité Battery Safety Precautions In French Per CSA RequirementsAVERTISSEMENT Conserver Ces InstructionsNumber of Cells Matching Battery Cabinets OptionalBattery Voltage VDC NominalTable 13 Battery retorque values Table 14 Battery voltage recordRack-Mounted Batteries Table 15 Torque specifications unless otherwise labeled 4.5 Detection of Trouble4.4.2 Torque Requirements 4.7 Corrective Actions 4.6 Reporting a Problem4.9 Upstream Feeder Circuit Breaker Setting Inspections 4.8 Recommended Test Equipment5.0 SPECIFICATIONS Figure 70 Output power envelope for 0.8 and 0.9 pf rated units5.1 Rating Table 17 Specifications applicable to environment Specifications5.2 Environmental Conditions 5.3 Adjustments 5.4 Battery Operation5.5 Electrical Specifications SpecificationsSystem overload capacity depends on Specifications Page Technical Support / Service Ensuring The High AvailabilityOf Mission-Critical Data And Applications reduced capital equipment and operating costs