Manuals / Emerson / Computer Equipment / Power Supply

Emerson Series 610 manual History Status, History status report screens

Models: Series 610

1 120

Download 120 pages 16.72 Kb

Page 46

History Status

Operation

History Status

The History Status screen displays 64 frames, of 4 milliseconds each, from the Present Status screen. Note that the values for output volts and amps are updated once each millisecond. Alarms are listed in the sequence they occurred, within 1 millisecond resolution. The frames are stored in a buffer (a computer information storage technique). The buffer stores the frames in a first in, first out sequence. As a new frame enters the buffer the oldest one is released.

When a designated fault occurs (see list below), the buffer stores information for the next 24 frames and then freezes (stops gathering information). At that time, the History Status screen contains

40 frames before the fault, the frame when the fault occurred and 23 frames after the fault. This

64-page report is a very useful diagnostic tool for the operator or Liebert Global Services. Use the Up and Down pads to view the screens.

Figure 25 History status report screens

	HISTORY STATUS				MODULE-0 04/10/97						16:49:21		FRAME 36
	ORDER - 000000			SITE ID - 00000			SITE TAG - 0000000
** ACTIVE ALARMS **					Output Ov-volts
					A	B	C	DC		LOAD		HERTZ TIME
OUTPUT VOLTS					480	480	480
OUTPUT AMPS					420	420	420
OUTPUT FREQUENCY									349			60.0
LOAD KVA					480	480	480		349
BYPASS VOLTS					480	480	480

											UP	: NEXT FRAME

											DOWN : PREVIOUS FRAME

										SELECT : EXIT




HISTORYSTATUS				MODULE-0-0 04/10/97/17/98					16:49:2111:21:59			FRAME36100
ORDER - 000000 SITE ID - 00000						SITE TAG - 0000000
** ACTIVE ALARMS **				BattOutputDischargingOv-volts			Low Batt Warning
				A	B	C	DC	LOAD			HERTZ		TIME
OUTPUT VOLTS				4380	4380	4380
OUTPUT AMPS				325530	325530	325530
OUTPUT FREQUENCY											650.0
OUTPUTLOAD KVAVOLTS				480	480	480		349
OUTPUTBYPASS VOLTSAMPS				32580	32580	32580	390
BATTERY VOLTS							390						0:01
OUTPUT VOLTS				480	480	480
OUPUT AMPS				325	325	325	-645
BATTERY AMPS							-645
INPUT VOLTS				0	0	0
INPUT AMPS				0	0	0					UP : NEXT FRAME
OUPUT VOLTS				480	480	480
OUPUT VOLTS				480	480	480					DOWN : PREVIOUS FRAME
OUTPUT AMPS				325	325	325					DOWN : PREVIOUS FRAME
LOAD KVA								270
LOAD KVA								270			SELECT : EXIT

40

Image 46

Emerson Series 610 manual History Status, History status report screens

Contents

AC Power Liebert Series 610 UPSFor Business-Critical Continuity BATTERY CABINET PRECAUTIONS CONTACTING LIEBERT FOR SUPPORTTABLE OF CONTENTS 4.0 MAINTENANCE 5.0 SPECIFICATIONSFIGURES TABLES IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS1.0 INTRODUCTION 1.1 System DescriptionFigure 1 Multi-Module UPS, 100-500kVA Figure 2 Multi-Module UPS, 500-750kVA Designed for Success 1.2 ReliabilityTypes of System Control Cabinets SCCs Figure 3 System Control Cabinets1.4 Modes of Operation 1.3 Safety Precautions1.4.2 Input Power Failure Other Factors to Consider1.4.3 Recharge 1.4.7 Maintenance Bypass1.4.8 Off-Battery 1.4.4 OverloadIntroduction 1. Battery 1.6 Options2. Battery Racks or Cabinets 2.0 THEORY OF OPERATION 2.1 General Component Descriptions2.1.1 System Control Cabinet Figure 6 UPS module block diagram 2.1.3 Battery Plant2.1.2 UPS Module 2.2.1 Controls Hardware 2.2 Detailed Component DescriptionsSoftware Operation Input Power Factor2.2.2 Rectifier/Charger Input Circuit BreakerBattery Charge Current Limiting 2.2.3 Battery Charging CircuitBattery Disconnect Battery Equalize Charge Circuit2.2.4 Inverter Non-Linear Load CharacteristicsUnbalanced Load Characteristics OperationFuse Protection Figure 7 System Control Cabinet block diagram2.2.5 Static Bypass Shorted SCR MonitoringPulsed Parallel Operation Static Switch IsolationLoad Transfers 2. Manual Transfers Transfer and Retransfer Conditions1. Automatic Transfers to Bypass 3. Transfer Inhibited2.2.6 Redundant Mode 6. Retransfer Inhibited3.1 Display Screen and Operator Controls Features3.0 OPERATION Operation Figure 8 Typical operator controlsTypical operator controls 500kVATypical SCCT System Control Cabinet operator controls Figure 9 Operator controls, typical SCCT System Control CabinetOperation Liebert Series 610 UPS and SCC operator control panels Figure 10 Liebert Series 610 UPS and SCC operator control panelsOperation Liebert Series 610 UPS and SCC operator control panels Figure 11 Switches behind SCC control panel doorOperation 3.2 Menu Tree Navigation Figure 12 Menu tree3.2.1 Master Menu Screen Figure 13 SCC and module master menu screensFrom any primary screen accessed directly from the Master Menu, pushing the Select pad once will return you to the Master Menu. From any secondary screen, pushing the Select pad twice will return you to the Master Menu Output Metering Displays 3.2.2 SCC Monitor/Mimic Display ScreenInput Metering Displays Figure 14 SCC Monitor/Mimic display screenItem 5 - Module Status Messages Status/Alarm Message AreasItem 7 - Alarm Messages Item 6 - System Status MessagesInput Metering Displays BATTERY VOLTS AMPS 15 CHARG3.2.3 Module Monitor/Mimic Display Screen Output Metering DisplaysAlarm Messages Item 5 - Alarm MessagesSCC Display Figure 16 Monitor/Mimic display example Normal power flowOperation Module DisplayFigure 17 Monitor/Mimic display example Utility fail Operation270 kVA / 217 kW Operation325A 325A 325A A B C 953A3780A 953A3780A 953A378A0A OperationMOD 1 ON LINE MVODLTS2 OFF540 LINE SUM ALM MODAMPS3 75ON15 CHARGLINE 50.0Hz 5060..00HzOperation MODAMPS3 75OFFCHARGLINE SUM ALM3.2.4 Walk-In Display Screen Figure 21 Walk-in display screen during start-upEach of the four Status Reports can be displayed on a remote terminal 3.2.5 Status Reports ScreensPresent Status Refer to 3.2.15 - Communication InterfacesFigure 24 Event history report screen Event HistoryFigure 23 Present status report screens, SCC above and module OperationHistory Status Figure 25 History status report screensAlarm in SCC Table 5 Alarm conditions that freeze history data gatheringAlarm in Module Figure 26 Battery cycle monitor screen System StatusEvent Figure 27 Battery cycle monitoring summary screenBattery Cycle Monitoring Summary Date3.2.6 System Configuration Screens Figure 29 SCC system configuration screenDate Figure 30 Date screenTime Figure 31 Time screenFigure 32 Auto dial setting screen Auto DialFigure 33 Modem baud rate Modem Baud RateMaximum Auto-Retransfer Attempts Figure 34 Maximum auto-retransfer attempts screenSystem Options System Current RatingLanguage Selection Figure 35 SCC system options screenFigure 38 Battery test results screen Figure 37 Battery test screen-MMU onlyContinuous Duty Static Switch Optional Remote Monitor Figure 39 Monitor/Mimic display example Continuous Duty Static SwitchSCC and module remote monitor indications 3.2.7 Alarm Limit Settings Screen Figure 40 Module alarm limit settings screenBattery Float Voltage Temperature Limit Setting Optional3.2.8 Load Transfer Procedures Screen Figure 41 Load transfer procedures screen3.2.9 Start-Up Procedures Screen Figure 42 SCC start- up procedures screen3.2.10 Shutdown Procedures Screen Figure 43 Module start- up procedures screensFigure 44 SCC shutdown procedures screen Figure 45 Module shutdown procedures screen3.2.11 Battery Time Screen Module Only Figure 46 Battery time screen 15 minute dischargeRemaining Figure 47 Battery time screen 45-minute dischargeFigure 48 Accuracy range of values for calculated battery times TimeDirty battery jar covers Battery age Excessive battery discharge/recharge cyclesLoose electrical connections Ambient temperature extremes Bad or weak cells Low acid levels in flooded cells3.2.12 Meter Calibration Screen Figure 49 Meter calibration screen3.2.13 Battery Equalize Screen Figure 50 Battery equalize screenFigure 51 SCC status and alarm message areas 3.2.14 Alarm and Status Messages Module Status MessagesSystem Status Messages Table 8 Abbreviations used in alarm messages Alarm MessagesLoad Block Messages Alarm messages - meaning and corrective action OperationAlarm messages - meaning and corrective action continued OperationRefer to 3.2.14 - Alarm and Status Messages Alarm messages - meaning and corrective action continuedOperation Operation Alarm messages - meaning and corrective action continuedDetermine the cause of the emergency condition and correct it if possible Operation Table 10 Alarm messages - summaryAlarm Message Special FunctionsAuto-Dial 3.2.15 Communication InterfacesWorldwide Reporting Requesting InformationLocal Reporting to a Monitor Local Reporting to a TerminalSite Reporting SiteScan or SNMP Remote Monitor Panel Table 11 Liebert Series 610 terminal commandsSeparate / Simultaneous Outputs Abbreviation 3.3 Modes of OperationTable 12 Circuit breaker abbreviations Circuit BreakerSCCT 3.3.1 Load on Bypass3.3.2 OK to Transfer Figure 52 Load on bypass, UPS not availableFigure 53 Load on bypass, UPS available SCCTSCCT Figure 54 Load on UPS, bypass available3.3.3 Momentary Overloads Figure 55 Momentary overload, pulsed static bypass switchSCCT SCCTFigure 56 Input power fail-load on battery 3.3.4 Input Power Failure-Load on BatterySCCT SCCT 3.3.5 One Module Off-LineFigure 57 One module off-line, load on UPS Figure 58 Load on UPS-battery not available 3.3.6 Off BatterySCCT SCCT 3.3.7 Emergency Modules OffFigure 59 Emergency modules off Figure 60 Emergency power off 3.3.8 Remote Emergency Power OffSCCT SCCT 3.3.10 Maintenance Bypass3.3.9 System Shutdown Figure 61 System shutdownSCCT Figure 62 Load on maintenance bypass, two breakersFigure 63 Load on maintenance bypass, three breakers SCCT3.4 Manual Procedures 3.4.1 SCC Start-Up ProcedureStep 1. Before you apply power to the UPS modules, determine the position of the following circuit breakers and switches 5. Set the Static Switch Disconnects to ON closed Figure 64 SCC start-up procedures screen 3.4.2 UPS Module Start-Up Figure 65 Module start-up procedures screen The Battery block in the Monitor/Mimic Display indicates the battery voltage and charge current 3.4.3 Load Transfer Procedures Figure 66 Load transfer procedures screenIf the load is on Maintenance Bypass 3.4.4 Maintenance Bypass Load TransfersIf the load is on the UPS System Bypass 3.4.5 Shutdown Procedures System Shutdown Procedure Figure 67 SCC shutdown procedures screenModule Shutdown Procedure Figure 68 Module shutdown procedures screen3.5 Automatic Operations Remote Emergency Power Off REPOLocal Emergency Modules Off LEMO 3.5.2 Automatic Transfers to Bypass 3.5.1 Overloads Without TransferFigure 69 Current-versus-time curves of module overload capacity 3.5.4 Automatic Module Off-Line 3.5.3 Automatic Retransfers to UPS3.5.5 Automatic Emergency Modules Off 4.1 Safety Precautions 4.0 MAINTENANCEProfessional Start-Up 4.2 Liebert Global ServicesMaintenance Agreements The Signature Program Training4.3.1 Record Log 4.3 Routine Maintenance4.3.2 Air Filters 4.3.3 Limited Life Components 4.4 Battery Maintenance 4.4.1 Battery Safety PrecautionsInstructions Importantes Concernant La Sécurité Battery Safety Precautions In French Per CSA RequirementsAVERTISSEMENT Conserver Ces InstructionsNumber of Cells Matching Battery Cabinets OptionalBattery Voltage VDC NominalTable 14 Battery voltage record Table 13 Battery retorque valuesRack-Mounted Batteries 4.5 Detection of Trouble Table 15 Torque specifications unless otherwise labeled4.4.2 Torque Requirements 4.7 Corrective Actions 4.6 Reporting a Problem4.9 Upstream Feeder Circuit Breaker Setting Inspections 4.8 Recommended Test EquipmentFigure 70 Output power envelope for 0.8 and 0.9 pf rated units 5.0 SPECIFICATIONS5.1 Rating Specifications Table 17 Specifications applicable to environment5.2 Environmental Conditions 5.3 Adjustments 5.4 Battery OperationSpecifications 5.5 Electrical SpecificationsSystem overload capacity depends on Specifications Page Technical Support / Service Ensuring The High AvailabilityOf Mission-Critical Data And Applications reduced capital equipment and operating costs