Signal | Return |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Pin | Pin | Signal | Direction | Description | ||||||||||||||
14 |
|
|
|
|
|
|
|
|
|
|
|
| IN | When this signal is LOW, the | ||||
|
|
|
|
| AUTO |
|
| |||||||||||
|
|
|
|
|
|
| FEED |
|
| paper | is | automatically fed | ||||||
|
|
|
|
|
|
|
|
| XT |
|
|
|
| one line after printing. | ||||
15 |
|
|
|
|
|
| NC |
| Not used |
| ||||||||
16 |
|
|
|
|
|
| O V |
| Logic ground level | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
17 |
|
|
|
|
|
|
| FG |
| Printer's chassis ground, | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| which is isolated from the | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| logic ground | ||
18 |
|
|
|
|
|
| +5V |
| Pulled up to +5V through | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3.3 | resistance. | |
|
|
|
|
| GND |
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ground level | ||
31 |
|
|
|
|
|
|
| IN | When this level becomes | |||||||||
|
|
|
|
|
|
| INIT |
| ||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| LOW, the printer controller is | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| reset to its state when the | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| power is first turned on and | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| the print buffer is cleared. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This level is normally HIGH; its | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| pulse width must be more | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| than 50 | at the receiving | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| terminal. |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
32 |
|
|
|
|
|
|
|
| OUT | This level becomes LOW | ||||||||
|
|
| ERROR | |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| when the printer is: | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1) In a | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| jam state | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2) When the PAUSE button is | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| pressed | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3) In an error state | ||
33 |
|
|
|
|
| GND |
| Signal | ground | |||||||||
3 4 |
|
|
|
|
|
| N C |
| Not used |
| ||||||||
35 |
|
|
|
|
|
| +5V | OUT | Pulled up to +5V through | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3.3 | resistance | |
36 |
|
|
|
| SLCTIN | IN | The DC1/DC3 codes are | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| valid only after this signal is | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| HIGH when the printer is | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| turned on. |